Aisidra AD-BA030 Bluetooth 5.0 Transmitter Receiver User Guide

Aisidra AD-BA030 Bluetooth 5.0 Transmitter Receiver User Guide

Package Contents

1. 1 x Wireless Adapter (TT-BA09 Pro)
2. 1 x 3.5mm Audio Cable
3. 1 x 3.5mm Female to RCA Male Cable
4. 1 x Optical Cable
5. 1 x USB-C Charging Cable
6. 1 x User Guide

Product Diagram

1. A for 1st Device
2. B for 2nd Device
3. Codec Indicators
4. Transmitter (TX) / Receiver (RX) Mode Switch
5. Power ON/OFF/Pairing
6. Power Indicator

BUTTON CONTROL

tndie to,

| Power ON| Flashing twice
Power OFF| Flashing twice
Standby Mode| Flashing every 5 seconds
Battery Low| Solid on
Charging| Solid on
Fully Charged| Off
A| Pairing| Flashing quickly
Connected| Solid on
Re-connect| Flashing slowly
B| Pairing| Flashing quickly
Connected| Solid on
SBC| Connected using the ABC codec| Solid on
APTX| Connected using the Apt-X^ codec| Solid on
LL| Connected using theApt-X Low Latency^ codec| Solid on

• SBC: SBC codec, supported by most Bluetooth® devices
• APTX: Apt-X® codec, the Bluetooth® device shall support Apt-X® codec. Prior than SBC.
• LL: Apt-X Low Latency® codec, the Bluetooth® device shall support Apt-X low latency®. Prior than SBC and Apt-X®.

HOW TO USE
Charging

1. Connect the charging port with any USB charging adapter or active computer USB port.
2. The Power indicator will stay solid on during charging. Once fully charged, it will turn off.

Note :

• You can use the adapter during charging, however, there might be background buzz noise.
• We recommend charging the unit for at least 2 hours before using it for the first time.

USE IN TX MODE

Note:

• If you want to experience LIP SYNC, make sure your Bluetooth® device supports apt-X Low Latency® codec. After connected, the Codec indicator “LL” will light up to indicate the low latency streaming codec.
• The default input mode is SPDIF. When the AUX cable is plugged in, it will switch to AUX mode automatically.
• Please do not connect TT-BA09 Pro to an amplifier output in TX mode, which may cause over-voltage and damage the adapter.

PAIRING WITH BLUETOOTH DEVICE

Note:

• After connecting with two Bluetoothe devices, the Codec indicator for the highest codec supported by both devices will light up (e.g., if device “A” supports SBC and Apt-X codec, while device “B” supports SBC codec, then Codec indicator “SBC” will light up).
• After disconnecting with one of the devices, the Codec indicator for the highest codec supported by the remaining device will stay on.

Use in TX Mode I Automatic Re-connect
TT-BA09 Pro can remember the devices paired previously, and will attempt to pair with the last connected devices (up to 2 devices) automatically once it is turned on.

Use in TX Mode I Clear Pairing History
When the adapter is off, clear the pairing history by sliding the Mode switch to “RX”, then power it on.

USE IN TX MODE

1. Ensure your TV speaker is set to “External Speaker”.
2. Ensure TV audio format is set to “PCM” or “Dolby/DTS” is OFF (This is IMPORTANT). 3) Ensure the optical audio cable is plugged in “SPDIF IN” port on TT-BA09 Pro.

Note:
Setting menu may be different depending on different TV brands and models.

TV WITH AUX 3.5mm AUDIO OUT

USE IN TX MODE

1. Set as default “Playback device” on PC/laptop – Right-click the speaker icon in the bottom-right of the taskbar and select “Playback devices”.
2. Set the “TT-BA09 Pro” as the “Default Device”.

Use in RX Mode I Initial Pairing

Pair with the 1st Bluetooth® Device

1. Slide the Mode switch to “RX” mode.
2. Press and hold the Power button for 3 seconds to turn on the adapter.
3. For the first use, TT-BA09 Pro will enter pairing mode automatically with indicator “A” flashing quickly.
4. Activate the Bluetooth® function on your phone/tablet, find “TaoTronics TT-BA09 Pro” in the search results and tap to connect. Once connected, the indicator “A” will turn solid on.

Pair with the 2nd Bluetooth® Device

1. After connecting with the 1st Bluetooth® device, press the Power button twice, the indicator “B” will flash quickly.
2. Place your 2nd Bluetooth® device close to the adapter (within 3 feet / 1 meter). Activate the Bluetooth® function on your phone/ tablet, find “TaoTronics TT-BA09 Pro” in the search results and tap to connect. Once connected, the indicator “B” will turn solid on.

Use in RX Mode I Automatic Re-connect
TT-BA09 Pro can remember the devices paired previously, and will attempt to pair with the last connected devices (up to 2 devices) automatically once it is turned on.

Use in RX Mode I Clear Pairing History
When the adapter is off, clear the pairing history by sliding the Mode switch to “TX”, then power it on.

TORUBLESHOOTING

connections and settings on TV/PC/Laptop.

Audio delay

| Make sure your Bluetooth ^ device suppOrts apt-X Low Latency° codec. AHer connected, the Codec indicator “LL” will light up to indicate the low latency streaming codec.
Pair with a new Bluetooth ^ device| When TT-BA09 Pro is powered on, press the Power button twice to enter pairing mode before reconnecting to the paired device.
Can’t reconnect with the last connected device| Each time you switch the modes, the pairing history will be cleared. Please re-pair with your Bluetooth^ device as instructed.

WARRANTY AND SERVICE

Thank you for choosing the TT-BA09 Pro Wireless Adapter. If any problems occur, please contact the TaoTronics Customer Care Centre in your country via the contact information listed in this User Guide.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>