Aisidra AD-BA010 Wireless 2-In-1 Adaptor User Guide
- June 10, 2024
- Aisidra
Table of Contents
Aisidra AD-BA010 Wireless 2-In-1 Adaptor
Product Contents
-
Wireless 2-in-1 Adapter (Model:AD-BA010)
-
3.5mm Audio Cable
-
3.5mm Female to
2 RCA Male Cable -
USB Charging Cable
Product Diagram
- LED Indicator
- Power Button
- Transmitter Mode
- Mode Switch
- Receiver Mode
- 3.5mm Audio Port
- Micro USB Charging Port
Specification
Bluetooth® Profile | A2DP/ AVRCP |
---|---|
Bluetooth Specification | Bluetooth 5.0 |
Audio Codec | TX: ap tXTM lowlatency, aptXr”‘, SBC |
RX: aptXT” lowlatency, aptXTM, SBC, AAC
Range| 33 ft/ 10 m
Battery Capacity| 160 mAh
Charging Power| 5VDC
Working Hours| 8-10hours
Charging Time| 2hours
Operating temperature| -10 to 55 C
Dimension (L x W x H)| 1.88 X 1.39 X 0.43 in/
4.80 x 3.55 x 1.10 cm
Weight| 0.53 oz/ 15 g
Use The Transmitter
Function | Operation |
---|---|
Power On | When off, press and hold the Power Button for 3 seconds |
PowerOff | When on, press and hold the Power Button for 3 seconds |
Pairing | When powered on, press the Power Button twice to start pairing |
Mode Switch | Slide the Mode Switch to and from TX and RX |
Reconnect To All Connected Devices | Short Press Power button to reconnect to |
all connected device; if no connected after 12 seconds will auto in paring
mode
Clear Pair List| When off, switch from TX mode to RX mode, then turn it on,
and the pairing list will be cleared.
Reset| When on, press power button and
plug it into power source at the same time.
Auto Power Off| Device will auto power off if battery lower than 3.1V
Low Battery Alarm| Device will have low battery alarm every 3 minutesif
battery lower than 3.3V
LED Indicators| Status
---|---
Solid Red LED| Charging
LED Off| Fully charged
Flashing Red and Blue| Pairing
Flashing Red| Low battery
Solid Blue LED| Successfully paired
Flashing Blue| Powered on but not paired with Bluetooth® devices
Use as Receiver
Function | Operation |
---|---|
PowerOn | When off, press and hold the Power Button for 3 seconds |
Power Off | When on, press and hold the Power Button for 3 seconds |
Pairing | When powered on, press the Power Button twice to start pairing |
Mode Switch | Slide the Mode Switch to and from TX and RX |
Play / Pause | In RX m ode, press the Power Button once to play / pause music |
Reconnect To All Connected Devices | Short Press Power button to reconnect to |
all connected device: if no con nected after 12 seconds will auto in paring
mode
Auto Power Off| Device will auto power off if battery lower than 3.1V
Low Battery Alarm| Device will have low battery alarm every 3 minutes if
battery lower than 3.3V
LED Indicators| Status
---|---
Solid Red LED| Charging
LED Off| Fully charged
Flashing Red and Blue| Pairing
Flashing Red| Low battery
Solid Blue LED| Successfully paired
Flashing Blue| Powered on but not paired with Bluetooth® devices
Flashing Blue twice| Unpaired and Standby
How to Use
Charging
- Connect the micro-USB end of the cable to the charging port of the Bluetooth
- Plug the USB end of the charging cable to a USB charging port or any active USB port.
- LED indicator will turn red when charging and will automatically turn off when fully
Note:
- You can use the adapter while it is
- We recommend charging the unit for at least 2 hours before using it for the first
How to Pair
Pair in TX mode
- Set Aisidra AD-BA010 to TX mode and connect it to the AUDIO OUTPUT jack of your non-Bluetooth devices such as TV/PC/MP3 player.
- Place your Bluetooth audio receiving device such as Bluetooth headphones/speaker within 3 feet I 1 meter and set it to pairing mode.
- Press and hold the Power Button for 5 seconds and tap twice to enter pairing mode (blinking red and blue). Within a few seconds, both devices will pair to each other and the transmitter will stay solid
How to pair with Airpods in TX mode?
- Make sure the adapter is set into TX mode, both devices are within 3ft to each other;
- Find the circular button on the rear side of the charging case of your Airpods;
- 0pen the lid of your Airpods, charging case (do not remove Airpods from the case)
- Tap and hold the circular button until the light inside the case blinks white;
- Turn on the adapter and it will automatically enter pairing mode (blinking red and blue);
- Both devices will search for each other and connect to each other within seconds. The transmitter will stay solid blue while the Airpods charging case will turn into green light once connected.
Pair in RX Mode
Press and hold the Power Button of the adapter for 3 seconds, it will start pairing.
-
Activate the Bluetooth function on your phone and search for the nearby Bluetooth devices:
● For iOS: Settings> Bluetooth > On
● For Android: Settings > Wireless & Networks >Bluetooth: On > Scan for devices -
Find “AD-BA01o” in the search results and tap on it to connect. Once connected, the LED indicator will turn solid blue.
Note:
- The adapter enters pairing mode automatically when powered on for the first
- The original paring memory in TX mode will be cleared after a mode switch, but in RX mode will not. It will automatically start pairing each time when powered on.
- If a PIN code is required for pairing, try 0000,8888,1111 or 1234.
- The adapter can remember two recently paired devices and will attempt to pair with devices automatically, without going into pairing mode.
- Please do not turn on the adapter right after it is turned off, otherwise, the adapter might crash and the battery will be damaged.
- If the adapter fails to pair with your devices, please kindly clear the pairing history of both devices and try to re-pair them following the pairing
- Bluetooth headphones / speakers are also required to support AptX Low Latency Codec to run low latency mode, otherwise, the receiving devic.e might use other codec (e.g. SBC, aptX), which might result in a 70-200ms audio delay that might be noticeable to some users.
Pair with two devices at the same time In TX mode
The adapter is able to pair witlh two Bluetooth® stereo earphones/speakers at the same time.
- Follow the previous instructions in the “Pairing” section to pair the AD-BA01o with your first
- Turn off the Bluetooth® function on your first device, tap the Power Button twice to pair and connect to your Second device.
- Turn on the Bluetooth® function on your first In approximately 12 seconds, the first device will automatically connect in.
Note:
- When you pair with two devices, both can play music at the same
- The adapter will automatically re-pair when powered on
In RX mode
The adapter is able to pair with two Bluetooth® devices at the same time
Turn on the Bluetooth® function on your first device. In approximately 12
seconds, the first device will automatically connect in.
In RX mode
The adapter is able to pair with two Bluetooth® devices at the same time.
- Follow previous instructions in the “Pairing” section to pair the AD-BA01o with your first device. Disable the Bluetooth® function on your first device. Tap the Power Button twice to pair with the second device.
- Turn on the Bluetooth® of the first device, now AD-BA01o adapter is successfully paired with both two devices.
Note:
-
Only one device can play music at any time.
You have to stop the music on one device to play on the other. -
The adapter will automatically re-pair when powered
Care and Maintenance
- Keep the adapter away from1 heat and
- Do not expose the adapter to direct sunlight or extreme heat.
- Do not try to take the adapter It may cause serious damage.
- Do not drop or knock the adapter on hard surfaces as it damages the interior circuit.
- Do not use chemicals or detergents to clean the
- Do not scrape the surface with sharp
Warranty and Service
This product is covered with Aisidra product and labor warranty for 12 months from the date of its original purchase.
Any questions? Contact:
Manufacturer
Shenzhen Zhonghantong Technology Co., Ltd Address: Rm 1521, Ocean Bldg,1050 Dongmen North Rd Mutoulong Community, Cuizhu Street, Luohu Dist, Shenzhen CHINA 518000
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>