Shen Zhen Gtl Technology G601 3 In 1 Fast Wireless Charger Instruction Manual

June 5, 2024
Shen Zhen Gtl Technology

Gtl Technology G601 3 In 1 Fast Wireless Charger
Instruction Manual

Product Introduction

  1. 15W wireless charging area for phone
  2. 5W wireless chargining area for earphone
  3. 3W wireless chargining area for watch
  4. Green indicator light
  5. Power supply interface Type-C

Steps for Usage
Just put your phone/watch/earphone in the wireless charging module and start charging.

Connect the external power supply to power on
2.1 Use an adapter that supports QC3.0, and connect the Type-C power cord to the G601 wireless charging socket interface.

2.2 Please fully insert the type-C power plug into the port, to avoid poor contact resulting in product power supply failure.
2.3 After the power is turned on, the LED indicator in the wireless charging area of the mobile phone is blue, and the LED indicator in the wireless charging area of the headset is green. The indicator lights flash three times and then go out, and enter the standby state.

Charging description

3.1 The mobile phone is placed vertically or horizontally in the 15W wireless charging area, symmetrically placed in the middle. and the green indicator light is always on, indicating that the charging is normal.
3.2 The earphone is placed in the 5W wireless charging area in a white bracket. Earp When the hone indicator light is always on, it means that the charging is normal.
3.3 Place the watch on the installed wireless charging module of the watch, and the watch will be fixed by magnetic suction. When the charging icon is displayed on the watch screen, it indicates that it is charging normally.
3.4 It is forbidden to paste metal sheets or metal protective cases on the back of the mobile phone, which will lead to the failure of charging.
3.5 When using a 5V/1A/2A adapter for wireless charging and power supply, due to the low input power, suggest using a single device for charging. When the input power is insufficient, charging multiple devices will cause the device to be disconnected or not charging.
Introduction to indicator lights
4.1 Equipped with blue and green LED indicators to show the charging status of the phone.
4.2 After the power is turned on, the blue and green LED indicators to flash three times and then go out, and enter the standby state.
4.3 The blue LED is always on when the mobile phone is charging, the green LED is always on when the headset is charging, it shows cyan when charging both at the same time.
4.4 When the mobile phone and earphone are charged in the wireless charging area, the blue, green, and cyan alternately flash to remind us when the charging is abnormal. Such as metal foreign body alarm.
4.5 When the mobile phone wireless charging area is charging normally, and the headset wireless charging area is charging abnormally, the blue and cyan colors alternately flash to remind.
4.6 The headset wireless charging area is charging normally, and the mobile phone wireless charging area is charging abnormally, the green and cyan colors alternately flash to remind.

Nance Wireless charger Model G601
Product size 185x146x14min Power supply port ‘5mm
nowt 9V—3A
12V—2A Output Phone: 15W Max

Watch: 3W Max
Earphone: SW Max

FCC WARNING STATEMENT

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.lf this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This equipment must be installed and operated in accordance with provided instructions and the antenna(s)used for this transmitter must be installed to provide a separation distance of at least 15cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals