Suntech ST4345GPS Enabled LTE CAT-M1 AVL Device User Manual

June 5, 2024
SUNTECH

Suntech ST4345GPS Enabled LTE CAT-M1 AVL Device

Introduction

This document describes features, protocols and detail operation of ST4345.

If there is another operation description document for special buyer to customize or model and the contents of the document is different with this, customizing document should be applied for special buyer.

Overview

Device consists of LTE-M1, GPS and event parts. The main purpose of device reports getting GPS position and other informs of vehicle to server periodically. Device can control or check connected lines and support additional functions.

Operation Mode

The device has 3 operation modes, driving, parking and emergency.
Driving : Driving status when ignition is on.
Parking : Parking status that starts if ignition is off during more than T1.
Emergency** : Once panic button is On or any other status as per designed.
The device sends emergency reports until A1 times or receiving server acknowledge.

Report

AVL reports GPS and some information at predefined interval, depending on the current modes. Also, AVL sends some alerts, for example, movement at the parking condition, changing of connected input line and so on.
Device distinguishes all reports with 6 types, Status report, emergency, event, alert, alive and command response.
Device can store reports when reporting route (For example, LTE-M1 condition) is not successful. Storage capacity is up to 2,000 status reports, 50 emergency reports, 50 alert reports (include event reports) and 1500 bytes as command response. In case of status reports, oldest report is erased and new report is buffered when the buffer is full and new status report enters (FIFO). When reporting condition is recovered, device starts sending all buffered reports. Also, this capacity can increase if it is needed.
Each type of reports has priority, and priority is as below.
Emergency ➔ Command Response ➔ Alert ➔ Status Report➔ Alive (Lowest)
Emergency is the first to be sent after recovering LTE-M1 condition.

Setting Parameter

Parameters of device can be changed by LTE-M1 or SMS, and some control can be realized also in the same way.
Detail protocols are described in Chapter 4.

Features

Key features are described here;

– Power Down
Device can process two steps of power-down, Sleep and Deep Sleep, for reducing power consumption when the vehicle is parked.

– LED Indicator
LED indicates LTE-M1 and GPS states. It’s helpful to check error cause.

– Events
Device has 2 output lines, 3 input lines and ignition line.

– Update Firmware by Over The Air (FOTA)
When Firmware of device has some error or has to be changed for a new service to be implemented, device can update internal ROM file by over the air (FOTA), remotely via LTE-M1. Customers do not need to visit every vehicle to download the new firmware. Method of FOTA describes at “SunTech_OTA_UA_Protocol” document in detail.

– Parking Lock
Device can check whether the vehicle moves off the preset parking boundary or starts driving without ignition on. In the case that it notes the unauthorized moving or driving, it sends emergency report immediately.

– Over speed
Device can check speed of vehicle and send alert of over-speed to server.

– GPS Antenna Checking
Device can alert when GPS antenna is disconnected. It’s applicable only for models that have external antenna.

– Main Power Checking
The device can recognize the main power and inform to server when main power line is disconnected or main power drops below preset value. It’s applicable only for battery model.

– Battery Error Alert
Device can alert about battery error related on charging. It’s applicable only for battery model.

Protocol Construction

All command and reports are string and follows below format.
Every filed is distinguished by semi colon.
All report string from device is ended by `r’ (0x0D).
Command message format (from server to device)

HDR| DEV_ID| VER| Field 1| Field 2| | Field n
---|---|---|---|---|---|---
Field| Definitions| Remark
---|---|---
HDR| String| “ST4345” + Command type
DEV_ID| 6 char.| Device ID of AVL
VER| “02”| Protocol Version. This is fixed with “02”.
Field 1 ~ n| String| Contents

Device ID is unique number of each device that consists of 6digits.
If the command has invalid value or DEV_ID of the command that is sent by LTE-M1 or SMS is not matched with DEV_ID of the unit.

Report message format (from device to server)

HDR| DEV_ID| SW_VER| Field 1| Field 2| | Field n
---|---|---|---|---|---|---
Field| Definitions| Remark
---|---|---
HDR| String| “ST4345” + Report type
DEV_ID| 6 char.| Device ID of AVL
VER| “001”| Software version that the device has.
Field 1 ~ n| String| Contents

Commands

When the device is received a command, it responds with response string and changes some parameters or acts related operation.

Network Parameters Setting
HDR DEV_ID VER AUTH APN USER_ID USER_PWD SEVER_IP SEVER_PORT
B_SEVER_IP B_SEVER_IP SMS_NO PIN_NO

● Definition : Set network parameters and PIN number.

Field Definitions Unit Remark
HDR “ST4345NTW” Command type
DEV_ID 6 char. Device ID
VER “02” Protocol Version
AUTH ‘0’ /‘1’/’A’ LTE-M1 authentication

0  : PAP(‘NO’ in Synctrack)
1  : CHAP(‘YES’ in Synctrack) A : Automatic LTE-M1 set.
In this case, parameters in APN, USER_ID and USER_PWD field should be empty.

APN| String| | Access Point Name
USER_ID| String| | ID for LTE-M1 Access
USER_PWD| String| | Password for LTE-M1 Access
SEVER_IP| String| | Server IP Address
SEVER_PORT| String| | Server Port
B_SEVER_IP| String| | Backup Server IP Address
B_SEVER_PORT| String| | Backup Server Port
SMS_NO| String| | Phone number what the device sends SMS report to.
This can be used for backup in the area that if LTE-M1 condition is not good. Or, it can be used main report method when IP and Port are empty.For no use, it should be empty.
PIN_NO| String| | PIN Number to release PIN lock if it is enabled

[command] ST4345NTW;850000;02;0;internet;;;111.111.111.111;8600;;;; [response] ST4345NTW;Res;850000;010;0;internet;;; 111.111.111.111;8600;;;; ST4345NTW;Res;850000;010;A1;tim.br;tim;tim; 111.111.111.111;8600;;;; ** If network does not require User ID and Password, these fields should be empty. _Automatic LTE-M1 Set _ It the device is set to ‘Automatic LTE-M1 Set’, the device set LTE-M1 parameters automatically depending on inserted SIM. For example, if Airtel SIM is inserted, the device set AUTH to 0, APN to “aitelLTE-M1.com”, USER_ID and USER_PASS to empty. And the device reports response string after adding real LTE-M1 parameters when automatic LTE-M1 set is selected.
Report Parameter Setting

● Definition : Set parameters related on report interval.

Field Definitions Unit Remark
HDR “ST4345RPT” Command type
DEV_ID 6 char. Device ID
VER “02” Protocol Version
T1 String Sec Interval for sending status report in parking mode Range : 0

~ 86400

If 0, report in parking will be sent only one time when

vehicle starts parking.

T2| String| Sec| Interval for sending status report in driving mode Range : 0 ~ 60000

If 0, report in driving will be sent only one time when vehicle starts driving.

T3| String| Sec| Interval for sending status report in emergency mode Range : 0 ~ 9999

If 0, emergency report will be sent only one time when emergency state occurs.

A1| String| | Number of attempts for emergency report until the device gets acknowledge from server If 0, no emergency report will be sent.
SND_DIST| String| Meter| Distance interval for sending status report. Range : 0 ~ 60000 (60km)

If 0, status report related on moving distance is disabled.

If not 0, stats report is send when traveled distance reaches predefined SND_DIST.

T4| String| Sec| Interval for sending keep alive string
SMS_T1| String| Min| Interval for sending status report in parking mode
SMS_T2| String| Min| Interval for sending status report in driving mode
SMS_PACK_NO| String| | Report No in one SMS message
ANGLE_RPT| String| Degree| Report STT message if it’s greater than ANGLE_RPT. 0 : Disable

Range : 1 ~ 179

RPT_TYPE| String| | Set the type of reporting. 0: FIFO : First in First Out.

1: LIFO : Last In First Out.

[command] ST4345RPT;850000;02;180;120;60;3;0;0;0;0;0;0;0 [response] ST4345RPT;Res;850000;010;180;120;60;3;0;0;0;0;0;0;0

** If report interval is set big number, network may disconnect LTE-M1 connection because LTE-M1 communication is not progressed for a long time. So, unit may not receive command by LTE-M1. T4 is for protecting against this disconnection by sending short data with short term.

** Alive report can be sent only when the device has no data to send during T4 interval.

Event Parameter Setting
HDR DEV_ID VER IGNITION T1 T2
IN1_TYPE IN2_TYPE IN3_TYPE IN1_CHAT IN2_CHAT IN3_CHAT
OUT1_TYPE OUT2_TYPE OUT1_ACTIVE OUT2_ACTIVE
PULSE1_NO PULSE1_ON PULSE1_OFF PULSE2_NO PULSE2_ON PULSE2_OFF
IN4_TYPE IN5_TYPE IN4_CHAT IN5_CHAT BAUD

● Definition : Set parameter related event.

Field Definitions Unit Remark
HDR “ST4345EVT” Command type
DEV_ID 6 char. Device ID
VER “02” Protocol Version
T1 String Sec Delay for entering idle mode after ignition goes to off
T2 String Sec Delay for entering active mode after ignition goes to on
IN1_TYPE ‘0’ ~ ‘7’ 0 = Falling Edge 1 = Rising Edge

2 = Both Edge (Falling & Rising) 3 = Panic Button
4 = Call1 Button 5 = Call 2 Button
6 = Reserved
7 = Anti-Theft Button
13 = Disable Immobilizer if it’s activated by jammer detector.
Default = ‘3’.Only the device that included voice option (audio circuit) can be set to ‘Call1 Button’ or ‘Call2 Button’.
IN1_CHAT| String| 100ms| Input1 chattering time. Range : 0 ~ 9999 Default = 3 sec.
If 0, input1 is not checked.
OUT1_TYPE| ‘0’ ~ ‘5’| | 0 = GPIO
1 = immobilizer
2 = Immobilizer & Auto active
Auto   active    means   immobilizer    is activated automatically when the vehicle starts parking.
3 = Pulse
4 = LED Out for indicating call status. Refer 7-2-3. 5 = Buzzer
OUT1_ACTIVE| ‘0’ or ‘1’| | 0 = Open when out1 is active
1 = GND when out1 is active
PULSE1_NO| String| | Pulse number when out1 type set to pulse. Range : 0 ~ 9999
If pulse no is 9999, pulsing runs permanently.
PULSE1_ON| String| 100ms| Active time of pulse1 Range : 0 ~ 9999
It should be set with even number.
PULSE1_OFF| String| 100ms| Inactive time of pulse1 Range : 0 ~ 9999
It should be set with even number.
BAUD| ‘0’ ~ ‘4’| | It’s available when extra events support RS232. Baud-rate
0 = No use 1 = 4800bps
2 = 9600bps
3 = 19200bps
4 = 38400bps
5 = 115200bps
If the device does not support RS232, it should be 0.

[command] ST4345EVT;850000;02;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0 [response] ST4345EVT;Res;850000;010;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0

If IGNITION is set to ‘0’, device doesn’t check driving or parking state of the vehicle. It reports status string with idle mode always, and cannot support parking lock and the service that enters sleep or deep sleep automatically when the vehicle is parked.
If IGNITION is set to ‘2’, the device checks driving or parking state of the vehicle with voltage range of vehicle’s battery. We named it as ‘Virtual Ignition’. Virtual ignition can operate when the device installed  into real vehicle and it may be need adjustment of voltage range for special vehicle. For setting method, please refer 6.3.
In case of pulse,   pulse time may have tolerance about dozens of ms.
Immobilizer, LED Blink line and Buzzer type cannot set both OUT1 and OUT2 simultaneously.
In case that a event is set to “door sensor”, active state means door is opened.
If device has the Handsfree kit, each time the volume up button is pressed once, the speaker volume is turned up as below.
0 -> 1 -> 2 -> 3 -> 4 ->5 ->0 -> 1 -> 2 ->3 -> 4 -> 5 – > 0 -> 1 -> ….
(0 : Volume mute, 5 :Max Volume)

Type of no supported event line is fixed to “No Use”.
Below table is for example of 4 line event model.

Field Definitions Unit Remark
HDR “ST4345EVT” Command type
DEV_ID 6 char. Device ID
VER “02” Protocol Version
IGNITION ‘0’ ~ ‘2’ Ignition using state 0 : Not use ignition 1 : Use

ignition Line

2  : Virtual ignition(power)

3  : Virtual ignition (motion)

T1| String| Sec| Delay for entering idle mode after ignition goes to off
T2| String| Sec| Delay for entering active mode after ignition goes to on
IN1_TYPE| ‘0’ ~ ‘5’| | 0 = Falling Edge 1 = Rising Edge

2 = Both Edge (Falling & Rising) 3 = Panic Button

4 = Call1 Button 5 = Call 2 Button

6 = Reserved

7 = Anti-Theft Button

13 = Disable Immobilizer if it’s activated by jammer detector.

Default = ‘3’.

Only the device that included voice option (audio circuit) can be set to ‘Call1 Button’ or ‘Call2 Button’.

IN1_CHAT| String| 100ms| Input1 chattering time. Range : 0 ~ 9999 Default = 3 sec.

If 0, input1 is not checked.

OUT1_TYPE| ‘7’| | 7 = No Use
OUT1_ACTIVE| ‘0’ or ‘1’| |
PULSE1_NO| ‘0’| |
PULSE1_ON| ‘0’| |
PULSE1_OFF| ‘0’| |
BAUD| ‘0’| | 0 = No use

[command] ST4345EVT;850000;02;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0 [response] ST4345EVT;Res;850000;010;1;60;0;3;8;8;30;0;0;6;6;1;0;0;0;0;0;0;0;8;8;0;0;0

** In case of event 4 line model, IN2_TYPE, IN3_TYPE, IN4_TYPE, IN5_TYPE, OUT1_TYPE and OUT2_TYPE should be ‘No Use’.

Type and chat time of non used event lines are set to ‘No Use’ and ‘0’ automatically although these filed of

command is set to other value.

LTE-M1 Parameter Setting
HDR DEV_ID VER SMS_LOCK SMS_MT1 SMS_MT2 SMS_MT3
SMS_MT4 IN_CALL_LOCK CALL_MT1 CALL_MT2 CALL_MT3 CALL_MT4 CALL_MT5
CALL_MO1 CALL_MO2

● Definition : Set parameters related SMS or Call.

Field Definitions Unit Remark
HDR “ST4345LTE-

M1”

| | Command type
DEV_ID| 6 char.| | Device ID
VER| “02”| | Protocol Version
SMS_LOCK| ‘0’ or ‘1’| | Lock of Receiving Commands by SMS Disable (0) / Enable (1)

If   enabled,   only   commands   that   receives    from

SMS_MT1 ~ MT3 number can be accepted.

SMS_MT1| String| Up to 20 char.| Phone number for SMS commands
SMS_MT2| String| Up to 20 char.| Phone number for SMS commands
SMS_MT3| String| Up to 20 char.| Phone number for SMS commands
SMS_MT4| String| Up to 20 char.| Phone number for SMS commands
IN_CALL_LOCK| ‘0’ or ‘1’| | Lock of Incoming Call Disable (0) / Enable (1)

If enabled, only call from CALL_MT1 ~ MT5 number

can be accepted.

CALL_MT1| String| Up to 20 char.| Phone number for call
CALL_MT2| String| Up to 20 char.| Phone number for call
CALL_MT3| String| Up to 20 char.| Phone number for call
CALL_MT4| String| Up to 20 char.| Phone number for call
CALL_MT5| String| Up to 20 char.| Phone number for call
CALL_MO1| String| Up to 20 char.| Phone number for outgoing call from device
CALL_MO2| String| Up to 20 char.| Phone number for outgoing call from device

[command] ST4345LTE-M1;850000;02;0;;;;;0;;;;;;; [response] ST4345LTE-M1;Res;850000;010;0;;;;;0;;;;;;;

** When SMS or Call numbers are not set, that field should be empty.

Service Parameter Setting
HDR DEV_ID VER PARKING_LOCK SPEED_LIMIT PWR_DN CON_TYPE
ZIP GROUP_SEND MP_CHK ANT_CHK BAT_CHK M_SENSOR CALL
GEO_FENCE DATA_LOG ANTITHFT_CNT1 ANTITHFT_CNT2 JAM_DET
JAM_CHK_DIST JAM_CHK_TM

● Definition : Set parameters related report.

Field Definitions Unit Remark
HDR “ST4345SVC” Command type
DEV_ID 6 char. Device ID
VER “02” Protocol Version
PARKING_LOCK ‘0’ or ‘1’ Parking lock enable (1) / disable (0)

If 1, the device checks vehicle position in parking periodically. When the vehicle goes off some boundary or starts moving over some velocity, the device reports

parking lock emergency.

SPEED_LIMIT| String| Km/h| Over speed limit

If 0, the device does not check over speed.

If 1 and the vehicle runes over predefined value, device reports speed alerts once.

PWR_DN| ‘0’ ~ ‘2’| | Power saving type

0 : Disabled sleep and deep sleep service 1 : Enabled deep sleep

2 : Enabled sleep

CON_TYPE| ‘0’ ~ ‘2’| | Connection Type with Server 0 = KEEP_CON

1 = KEEP_DISCON

2 = KEEP_NOP

Detail explanation is below.

ZIP| ‘0’ or ‘1’| | Use Zip

Disable (0) / Enable (1)

GROUP_SEND| ‘0’ or ‘1’| | Group Send for stored data 0 : Disable

1 : Enable. One packet can include up to 5 reports.

Group send is explained below.

MP_CHK| ‘0’ or ‘1’| | Main Power Disconnection Check

Disable (0) / Enable (1)

ANT_CHK| ‘0’ or ‘1’| | GPS Antenna Connection Error Check

Disable (0) / Enable (1)

BAT_CHK| ‘0’ or ‘1’| | Backup Battery Error Check

Disable (0) / Enable (1)

M_SENSOR| ‘0’ ~’4’| | Motion Sensor
| | Motion| Collision| Shock
0| Disable| Disable| Disable
1| Enable| Disable| Disable
2| Disable| Disable| Enable
3| Enable| Disable| Enable
4| Disable| Enable| Disable
5| Enable| Enable| Disable
6| Disable| Enable| Enable
7| Enable| Enable| Enable
CALL| ‘0’ or ‘1’| | Support Call with headset

Disable (0) / Enable (1)

GEO_FENCE| ‘0’ or ‘1’| | Support Geo-fence

Disable (0) / Enable (1)

DAT_LOG| ‘0’ or ‘1’| | Log out with RS232 0 = No Use

1 = Enable getting saved log data by RS232

[command] ST4345SVC;850000;02;1;120;0;0;0;0;1;1;1;0;0;0;0;0;0;0;0;0 [response] ST4345SVC;Res;850000;010;1;120;0;0;0;0;1;1;1;0;0;0;0;0;0;0;0;0

** Function of M_SEMSOR can be used with the model that has motion sensor.

If shock or collision detection is enabled, device will report to server when gets any shock or collision.

** If this parameter has been customized, This table should be disregarded and you should follow customized

operation document.

_CONTYPE

1.     KEEP_CON : The device keeps TCP connection always and can receives a command by LTE-M1.

2.     KEEP_DISCON : The device connects TCP connection when the data is sent. After sending, the device disconnects LTE-M1 and TCP connection if it estimates there is no data for sending within 3minutes. In this case, it cannot receive a command by LTE-M1.

3.     KEEP_NOP : The device doesn’t send any report after be installed. When the device enters emergency mode or receive ‘Start Report’ command by SMS or RS232, it starts report depending on report parameters. It may be used for saving LTE-M1 fee. Current version cannot support this
option.

Group Send
The device stores data if the vehicle is in no LTE-M1 area. And, the vehicle moves to LTE-M1 available area,
device starts sending stored data.
If group send option is enabled, the device makes 5 reports to one bundle and send these 5 reports at one
time.
Group send is useful to speed up sending.

M_Sensor

  1. Collision: The device sending a event when ignition is ON and have a motion.
  2. Shock: The device sending a event when ignition is OFF and have a motion.

Jamming detection procedure
JAM_CHK_DIST & JAM_CHK_TM are assist for jamming detection to avoid false detection.
At least, we recommend use JAM_CHK_DIST for safety.
If you use two assist functions, it can detect two case of jamming as follows.

Case of jamming LTE-M1 only.
Jamming detected -> JAM_CHK_DIST -> JAM_CHK_TM -> Triggered by JAM_DET mode.
Case of jamming LTE-M1 & GPS.
Jamming detected -> JAM_CHK_TM -> Triggered by JAM_DET mode.

JAM_CHK_DIST : if 0, skip this function.
JAM_CHK_TM : if 0, skip this function.

If disable all of assist functions, just triggered by HAM_DET mode after detected jamming.
In this case, it’s possible to false detection in weak LTE-M1 or strong radio area.

Additional Parameters
HDR DEV_ID VER SVR_TYPE B_SVR_TYPE UDP_ACK DEV_PORT

● Definition : Setting additional parameter requested.

Field Definitions Unit Remark
HDR “ST4345ADP” Command type
DEV_ID 6 char. Device ID
VER “02” Protocol Version
SVR_TYPE ‘T’ / ‘U’ Server Protocol Type T : TCP

U : UDP

B_SVR_TYPE| ‘T’ / ‘U’| | Backup Server Protocol Type T : TCP

U : UDP

UDP_ACK| ‘0’ ~ ‘3’| | ACK from Server when UPD is used. 0 : No use

1 : ACK when the server receives reports except alive.
2 : ACK when the server receives reports except STT and alive report.
3 : ACK when the server receives emergency report.
Command response doesn’t need ACK.

DEV_PORT| String| | Device’s port for receiving command from UDP server. It can be used only when UDP server is used.

If ‘0’ or empty, the device would use port 9000.

If not zero, the device can receive commands with port

DEV_PORT.

Reserved| ‘0’| |
Reserved| ‘0’| |
Reserved| ‘0’| |
Reserved| ‘0’| |
Reserved| ‘0’| |
Reserved| ‘0’| |

[command] ST4345ADP;850000;02;U;T;2;9000;0;0;0;0;0;0 [response] ST4345ADP;Res;850000;022;U;T;2;9000;0;0;0;0;0;0

This command can be applied from software version 22.

ACK in case of UDP

UDP is protocol that doesn’t check whether the data is transmitted successfully. So, the device checks completion of sending with ACK depending on UDP_ACK type.

ACK is sent by server when the data is received.

If the ACK is not sent during more than 2 minutes after sending, the device recognizes the data was not reached to server and sends the data again

Examples of ACK report are as below.
String Format : “ ST4345ACK ;850000”
Zip Format : 0x15 0x85 0x00 0x00
It is recommended ACK_TYPE is set to ‘1’ to confirm all data can be transmitted safely.

Report Type UDP_ACK=0 UDP_ACK=1 UDP_ACK=2 UDP_ACK=3
Alive

| ☓| ☓|

STT|

| ○| ☓|

Event, Alert, Etc.|

| ○| ○|

Emergency|

| ○| ○|

Set Parameters of Main Voltage
HDR DEV_ID VER CHR_STOP_THRES_12 DECIDE_BAT_12
OPERATION_STOP_THRES_12 IGNDET_H IGNDET_L

● Definition : Set some value of main voltage.

Field Definitions Remark
HDR “ST4345MBV” Command type
DEV_ID 6 char. Device ID
VER “02” Protocol Version
CHR_STOP_THRES_12 String Voltage value to stop backup battery charging in

12V vehicle.
DECIDE_BAT_12| String| Voltage value to check whether the vehicle’s battery is 12V.
OPERATION_STOP_THRES_12| String| Voltage value to protect vehicle battery.

The device operation stops if car battery voltage is lower than this value in vehicle that has 12V power.

IGNDET_H

|

String

| In case of virtual ignition, the vehicle can recognize driving state when vehicle power is more than IGNDET_H.

Default = ‘0’

IGNDET_L| String| In case of virtual ignition, the vehicle can recognize parking state when vehicle power is less than IGNDET_L.

Default = ‘0’

< example> [command] ST4345MBV;850000;02;10.5;22;19;8.00;18.00;0;0 [response] ST4345MBV;Res;850000;122;10.5;22;19;8.00;18.00;0;0

< note>

IGNDET_H and IGNDET_L are ‘0’, device check parking and driving automatically.

Set Parameters of Motion Sensor
HDR DEV_ID VER CHR_STOP_THRES_12 DECIDE_BAT_12 OPERATION_STOP_THRES_12
IGNDET_H IGNDET_L VI_ON_THRES VI_ON_DELAY
VI_ON_PERCENT VI_OFF_THRES VI_OFF_DELAY VI_OFF_PERCENT

● Definition : Set motion sensor parameter

Field Definitions Unit Remark
HDR “ST4345MSR” Command type
DEV_ID 6 char. Device ID
VER “02” Protocol Version
SHOCK_DELAY String Sec. Delay for entering shock detection mode after

ignition off 0 – Disable
Range : 1 ~ 21600 (5hour)
Recommend : 600 ( 10 min.)
MOTION_THRES| String| Step| Detection level of shock violation. Range : 0.04 ~ 2.0
Recommend : 0.04
SHOCK_THRES| String| Step| Detection level of shock violation. Range : 0.04 ~ 2.0
Recommend : 0.04
COLL_THRES| String| Step| Gravity for collision report.

Range : 0.1 ~ 2.0
Recommend : 0.7

VI_ON_THRES| String| 1/255G| Threshold value for Motion Virtual Ignition On Range : 3~50

Default : 5

VI_ON_DELAY| String| Sec.| Delay time for Motion Virtual Ignition On Range : 3~999
Default : 10
VI_ON_PERCENT| String| %| Percent for Motion Virtual Ignition On. Range : 30~100

Default: 70

VI_OFF_THRES| String| 1/255G| Threshold value for Motion Virtual Ignition Off Range : 3~50

Default : 5

VI_OFF_DELAY| String| Sec.| Delay time for Motion Virtual Ignition Off Range : 3~999

Default : 10

VI_OFF_PERCENT| String| %| Percent for Motion virtual Ignition Off. Range : 30 ~ 100

Default : 70

[command] ST4345MSR;;02;600;0.04;0.04;0.7;5;10;70;5;10;70 [response] ST4345MSR;Res;852588;128;600;0.04;0.04;0.70;5;10;70;5;10;70
  • For the shock level, we recommend it to set to 0.04. if it’s over   than 0.04, the sensor will be more insensitive

as it for shock detection.

Control Command
HDR DEV_ID VER CMD_ID

● Definition : Controls some functions.

Field Definitions Unit Remark
HDR “ST4345CMD” Command type
DEV_ID 6 char. Device ID
VER ‘01’ Protocol Version
CMD_ID String Control command content

Caution : If it’s not correct the Unit ID, ignored.

Status Request

● Definition : Location poll, request of the status report.

Field Definitions Unit Remark
CMD_ID “StatusReq” Status request

If received, the device sends status string instantly.

[command] ST4345CMD;850000;02;StatusReq [response] ST4345STT;850000;010;20090724;07:12:16;00129;+37.479995;+126.885815;000.029;000.00;

7;1;0;15.33;100000;2;0002

Reset

● Definition : Reset all of parameters.

Field Definitions Unit Remark
CMD_ID “Reset” Reset

Initialize all parameters with factory value and reboot the device.

[command] ST4345CMD;850000;02;Reset [response] ST4345CMD;Res;850000;010;Reset
Preset

● Definition : Reset all of parameters.

Field Definitions Unit Remark
CMD_ID “Preset” Report parameter setting values and current device status.

Response includes network, report, event, LTE-M1 and service parameters. It includes status of device, also.

[command] ST4345CMD;850000;02;Preset [response] ST4345CMD;Res;850000;010;Preset;

NTW;0;internet;;;111.111.111.111;8600;;;;1234;

RPT;60;180;120;60;3;0;0;;;;

EVT;1;60;0;3;2;2;30;20;20;1;1;1;0;0;0;0;0;0;0;0;0;0;0;0;

LTE-M1;0;;;;;0;;;;;;;;

SVC;1;120;0;0;0;0;1;1;1;0;0;0;0

DEV;0;0;0;0

[response] event 4 line model

NTW;0;internet;;;111.111.111.111;8600;;;;1234;

RPT;60;180;120;60;3;0;0;;;;

EVT;1;60;0;3;8;8;30;0;0;6;6;1;0;0;0;0;0;0;0;0;0;0;0;0;

LTE-M1;0;;;;;0;;;;;;;;

SVC;1;120;0;0;0;0;1;1;1;0;0;0;0

DEV;0;0;0;0

** After power on, device sends response string of preset once.

** DEV filed informs current status of device as below.

| OUT1

0 = Disable

1 = Enable

| OUT2

0 = Disable

1 = Enable

| PWR_DN

0 = Normal

1 = Sleep

2 = Deep sleep

| BAT_CON

0     =     Backup     battery     is disconnected.

1 = Backup battery is connected.

---|---|---|---
Field| Definitions| Unit| Remark
---|---|---|---
CMD_ID| “PresetA”| | Report all parameters including additional parameter.

[command] ST4345CMD;850000;02;PresetA [response] ST4345CMD;Res;850000;010;PresetA;

NTW;0;internet;;;111.111.111.111;8600;;;;1234;

RPT;60;180;120;60;3;0;0;;;; EVT;1;60;0;3;2;2;30;20;20;1;1;1;0;0;0;0;0;0;0;0;0;0;0;0; LTE-M1;0;;;;;0;;;;;;;; SVC;1;120;0;0;0;0;1;1;1;0;0;0;0; ADP;U;T;2;9000;0;0;0;0;0;0; DEV;0;0;0;0;0;0;0;0 This command can be applied from software version 22. DEV filed informs current status of device as below

| OUT1

0 = Disable

1 = Enable

| OUT2

0 = Disable

1 = Enable

| PWR_DN

0 = Normal

1 = Sleep

2 = Deep sleep

| BAT_CON

0     =     Backup     battery     is disconnected.

1 = Backup battery is connected.

---|---|---|---
TRACKING

0 = Stop Tracking

1 = Start Tracking

| Anti-Theft 0 = Disable

1 = Enable

| Reserved| Reserved
---|---|---|---

ACK of Emergency

● Definition : Stop emergency report.

Field Definitions Unit Remark
CMD_ID “AckEmerg” Acknowledgement of emergency report.

The device will stop emergency reports if it is in emergency state.

[command] ST4345CMD;850000;02;AckEmerg [response] ST4345CMD;Res;850000;010;AckEmerg
Enable1

● Definition : Active Output1.

Field Definitions Unit Remark
CMD_ID “AckEmerg” Acknowledgement of emergency report.

The device will stop emergency reports if it is in emergency state.

[command] ST4345CMD;850000;02;AckEmerg [response] ST4345CMD;Res;850000;010;AckEmerg
Disable1

● Definition : Inactive Output1.

Field Definitions Unit Remark
CMD_ID “AckEmerg” Acknowledgement of emergency report.

The device will stop emergency reports if it is in emergency state.

[command] ST4345CMD;850000;02;AckEmerg [response] ST4345CMD;Res;850000;010;AckEmerg
Request IMSI

● Definition : Inactive Output1.

Field Definitions Unit Remark
CMD_ID “ReqIMSI” Request IMSI (unique SIM ID)

If received, device sends IMSI of using SIM.

[command] ST4345CMD;850000;02;ReqIMSI [response] ST4345CMD;Res;850000;010;ReqIMSI;724031111553779
Request ICCID

● Definition : Request the ICCID.

Field Definitions Unit Remark
CMD_ID “ReqICCID” Request ICCID (sequence number that is displayed on SIM)

If received, device sends ICCID of using SIM.

[command] ST4345CMD;850000;02;ReqICCID [response] ST4345CMD;Res;850000;010;ReqICCID;89550230000084256668
ReqVer

● Definition : Request software version.

Field Definitions Unit Remark
CMD_ID “ReqVer” Request device version

Device reports Model, Buyer, Protocol and S/W release version.

[command] ST4345CMD;850000;02;ReqVer [response] ST4345CMD;Res;850000;010;ReqVer;ST4345E_SAMPLE_STBASE_001
Erase All

● Definition : Erase all of data in buffer.

Field Definitions Unit Remark
CMD_ID “EraseAll” Erase saved all reports and disable outputs.

This is needed to initialize just before device is delivered to a customer.

[command] ST4345CMD;850000;02;EraseAll [response] ST4345CMD;Res;850000;010;EraseAll
Initialize Traveled Distance

● Definition : Initialize the travel distance.

Field Definitions Unit Remark
CMD_ID “InitDist” Set traveled distance to 0.
[command] ST4345CMD;850000;02;InitDist [response] ST4345CMD;Res;850000;010;InitDist
Initialize Message Number

● Definition : Initialize the message sequence number.

Field Definitions Unit Remark
CMD_ID “InitMsgNo” Set message number to 0.
[command] ST4345CMD;850000;02;InitMsgNo [response] ST4345CMD;Res;850000;010;InitMsgNo
Reboot

● Definition : reboot unit.

Field Definitions Unit Remark
CMD_ID “Reboot” Reboot device.
[command] ST4345CMD;850000;02;Reboot [response] ST4345CMD;Res;850000;010;Reboot
Request SIM IP Address

● Definition : Request of the local IP address in SIM card.

Field Definitions Unit Remark
CMD_ID “ReqSIMIP” SIM card IP request
[command] ST4345CMD;850000;02;ReqSIMIP [response] ST4345CMD;Res;850000;010;ReqSIMIP;172.16.18.6

Installation

Insert SIM card

Backup battery

– The backup battery should be used when main power is cut off

Install

– The Device is fixed to the vehicle.

Assemble as below

Event Cable Color pin Description

Red: VCC (12V)
Black: Ground

Trouble Shooting (LED Indicator)

Blue LED: Indicates LTE-M1 status.
LTE-M1 Blink Count Remarks
Normal 1 ![](https://manuals.plus/wp-

content/uploads/2022/04/5-529-550x38.png)
Server Com. Error| 2|

  1. Server or network parameter is wrong.
  2. Server is closed.
  3. Temporary network barrier

LTE-M1        Com.

Error

| 3|

  1. Network parameter is wrong.
  2. SIM is blocked about LTE-M1 using.
  3. Temporary network barrier
  4. Weak LTE-M1 signal
  5. LTE-M1 antenna connection is not firm.

No Network| 4|

  1. LTE-M1 antenna is disconnected.
  2. LTE-M1 antenna or socket of LTE-M1 antenna is broken.
  3. Device is broken.

SIM PIN Locked| 5|

  1. SIM PIN is enabled.

Cannot      Attach NW| 6|

  1. Weak LTE-M1 signal.
  2. LTE-M1 antenna connection is not firm.

No SIM| 7|

  1. There is no SIM or SIM is not inserted properly.
  2. SIM or SIM socket is broken.
RED LED: Indicates GPS status.
GPS Blink Count Remarks
Normal 1 ![](https://manuals.plus/wp-

content/uploads/2022/04/12-292-550x38.png)
No Fix| 2|

  1. If power on, GPS chipset is trying to find position during some minutes.
  2. GPS antenna lays on weak or no GPS signal position
  3. GPS antenna connection is not firm.

GPS Chipset Error GPS Antenna Error| 4|

  1. GPS antenna is disconnected.
  2. GPS antenna or socket of GPS antenna is broken.
  3. Unit is broken.

Safety information

*. Caution.1 :

  • High or low extreme temperature that a battery can be subjected to during use, storage or transportation
  • Low air pressure at high altitude
  • Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
  • Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
  • A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

*. Caution.2 : Don’t use USB Connect. USB Connect is only use for production.

FCC Part 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Part 15.21
Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.

FCC Part 15.105 Note :
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Modifications not expressly approved by the manufacturer could void your authority to operate the equipment under FCC rules.

Suntech International Ltd.

Documents / Resources

| Suntech ST4345GPS Enabled LTE CAT-M1 AVL Device [pdf] User Manual
ST4345, WA2ST4345, ST4345GPS, Enabled LTE CAT-M1 AVL Device
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals