Anicanon A1rmbjiVSCL Solar Security Cameras Wireless Outdoor User Manual

2.4G Wireless
Solar Security Camera
User Manual

Packing List

Product overview

Card Slot of the Wifi Camera:

NOTE: Use tweezers to install or pull out the TF card
CAUTION: Please insert the Micro SD Card according to the direction shown in the diagram.Micro SD Card might JAM if inserted incorrectly and device could be damaged
SD Card Port :Support micro SD card for local storage (Max 128GB).Reset button :Used to restore the camera to factory settings (Press and hold on 5-8S)Card capacity requirements:8-128GBRead and write speed requriements:class 10 level.File format:FAT32.

Battery:

NOTE: For the first use, please charge the battery full. The battery needs 6 hours to be fully charged.

App Installation

To install the app, scan the QR code below or search “UBox” in App Store (iOS devices) or Google Play (Android devices)

• from Google Play
• from Apple Store
• or Scan the fol lowing QR code

http://app.ubianet.com/app/ubox

Camera Installation Instructions

Select Height and location
Hang the camera 7-10 ft (2-3 m) above the ground. This height maximizes the detection range of the motion sensor of the camera. Avoid placing the camera under direct sunlight.

Installation

1. Drilling according to position sticker, drill bit: 15/64″(6 mm).
2. Insert the plugs.
3. Tighten the screw.

NOTE: Long screws are prohibited in the wholistic installation.

Select Height and location

1. keep the installation angle of solar panels about 30-45° with the horizontal plane, as shown in the picture below.
2. The installation between the solar panel and the camera is shown in the following figure(open up the silicone cover at the bottom of the camera, remove the small center part of the cover, insert the power cord through the opening and plug it into the Type C  port and then close the cover taking up slack in the power cord from the solar panel).

Select Height and location

1. When installing in the northern hemisphere, face the panel to the south, and when installing in the southern hemisphere, face the panel to the north.
2. Take care to install the solar panel so that the sun is not blocked by any items such as eaves, trees branches, etc.

Test the Wifi signal at installation position

Use cell phone to test Wifi signal quality at the installation position before installing camera, make sure the Wifi router can provide good Wifi signal. Register an account

The UBox app that is necessary to operate the camera.
Signing up for storage in the cloud is totally optional and is really not necessary when using an onboard Micro SD card.

1. Open the APP to sign up an account. Go to the login interface, and click “Sign Up”.
2. Sign up with your email address, and click “Register”.
3. Set up an “Password” for your APP, click “Register” to complete.

Set up WiFi for the camera

1. Bring both your mobile phone and your camera close to your router (max distance of 5 meters/16 feet).
   Note: The carnera can only connect to a 2.4 GHz WiFi signal. It does not support using a 5 GHz signal. Therefore, please ensure you connect to a 2.4 GHz signal on your network as shown in the below illustration.

WiFi Connection

1. Click “Add Family” to set rooms or locations
2. Input your last name, then click “Next”
3. Input necessary information, such as country, state,then click finish
4. Click “add devices” button to add smart devices NOTE: For 2.4GHz Wifi routers, either username or password is no more than 32 letters.
5. Click “Set Wifi Devices”
6.  If the blue LED isn’t on, please refer to the following configuration instruction
7. Input Wifi password to connect. This device does not support 5G Wifi for now. Please use 2.4G Wifi
8. Aim the QR code on the phone to the camera to scan it. Keep the distance at 10cm.
9. Connection succeed. Click “Done”.

Device Settings

NOTE: Users are able to modify the sensitivity of PIR detection. It is suggested that the sensitivity be set as “Disabled” or “Low” in order to reduce alarm frequency and save the battery in a noisy environment.

• Disabled: PIR detection does not work.
• Low: PIR detected the movement 7 seconds earlier.
• Medium: PIR detected the movement 5 seconds earlier.
• High: PIR detected the movement 1 second earlier.

Click the “Calendar” button and select a date to play videos in storage Check all videos from specific date by selecting the date

Q/A

Having worked for months, the camera does not turn into any direction. Nor is waken up by PIR. However, users can remotely check or control it via phone.

Cause: The battery is low. Solution: Charge the camera, using Type-C cable and DC-5V power,for about 2 seconds, which reactivates battery protection. The camera will turn again. Now you need to charge the battery full and install it on the wall. 1. Before using the camera, please charge the battery full. The battery lifespan is affected by the wake-up times of the camera. Therefore, PIR detection should be used in crowds. It is suggested that the camera should be turned off or set as low sensitivity in order to reduce the wakeup times and extend the battery lifespan. Promptly charge the battery when the battery is low. 2. The camera is designed yo be exquisite and low power consumption. Every time the camera is waken up and works for a few seconds, then, it will be on standby to save the battery. You can set the length of working time in settings. 3. Keep the camera within the router signal distance. Make sure the camera is placed near the Wi-Fi router.If there is something thick or insulating between the device and WiFi router, it may lead to low wifi signal. Please make sure that the wifi v signal is good before using the camera. NOTE: the red/blue warning lights leads to the synchronization with sound alarms. (When the call is on, the red and blue warning lights are also on)

Q: How bright are the lights

Q: How can I set the camera to send notifications to my phone.

Q: How can i delete the videos files from off the card

A: First ,i would to say that our solar security camera's purpose is to record the human motion

Q: Can more than one person access this camera

Q: Won't connect to 5G network

A: This item only work on 2.4GHz WiFi. Longer transmission distance than 5G.

Q: Not have auto tracking

A: This camera's work mode is pir motion detection ,when body goes in to it's field of view ( 85 degree), the camera will wake up and send a notification to your Phone . camera dosen't automatic track.

Q: Can the camera capture the license plate in the night clearly

A: No, usually the camera that takes photos of the license plate is dedicated, because cars at night usually have lights, and when the camera sees the car's lights, the screen will appear white, That is to say, ordinary cameras do not have the function of suppressing strong light. If your car's taillights are too bright, the camera's infrared light will automatically turn off, and the license plate will also reflect light, This has a significant impact on the camera capturing video files, Moreover, the characters on the license plate are very small, and they are almost indistinct at around 10 meters In addition, its exposure compensation and other aspects cannot meet the requirements of the camera for license plate

Customer Service Email: vip@anicanon.com
Free replace / return, usage issues, please Email us Reply within 24 hours

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>