TAOTRONICS TT-AH044 Ultrasonic Cool Mist Humidifier User Guide

June 5, 2024
TaoTronics

TAOTRONICS TT-AH044 Ultrasonic Cool Mist Humidifier

TAOTRONICS TT-AH044 -Ultrasonic- Cool Mist -Humidifier-
PRODUCT

STATEMENT

Thank you for purchasing a TaoTronics product that has been tested to meet our stringent quality standards. This product is covered with TaoTronics product and labor warranty for 12 months from the date of its original purchase. Please email us with your order ID and problem or issue via [email protected], we will respond within 24 hours.  Please read the User Guide thoroughly. Clean and maintain the product as instructed. If any abnormalities occur, please refer to the Troubleshooting Guide first. This warranty is void if the defect is caused by accidental damage, misuse, abuse, neglect, improper repair or alteration by unauthorized persons, or a failure to follow operating instructions provided with the product including adding essential oils directly into the tank and base. This warranty does not apply to normal wear and tear or commercial use. In no event shall liability exceed the purchase price paid by the purchaser of the product. Under no circumstances shall there be liability for any loss – direct, indirect or incidental – or consequential damage arising out of, or in connection with the use of the product.

SAFETY INSTRUCTIONS

The humidifier was made with safe and environmental protection materials, it has been certified and complied with the requirement of sale regions’ related regulations or laws.
IMPORTANT: Please read and save this SAFETY INSTRUCTIONS before using the device. Basic precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons or damage to the product. For indoor humidifying use only.

BEFORE USING THE HUMIDIFIERTAOTRONICS TT-AH044 -Ultrasonic- Cool Mist
-Humidifier- FIG 1

  1.  Please extend the cord and check any signs of damage. Do not use the humidifier if the cord has been damaged.
  2. DO NOT place this humidifier in wet environments.

Please always keep the humidifier out of reach of patients & children & pet. TAOTRONICS TT-AH044 -Ultrasonic- Cool Mist -Humidifier- FIG
3

  1. Please always place the unit on a smooth, flat, lint-free, non-metallic, waterproof and level surface and keep it away from direct sunlight.
  2. Always place the unit 2 feet (60 cm) above the floor, 12 inches (30 cm) away from the wall, other appliances or wooden furniture.TAOTRONICS TT-AH044 -Ultrasonic- Cool Mist -Humidifier- FIG 4

DO NOT place the humidifier near naked flames and heat sources, such as stove tops, ovens, radiators or computers.

WHEN USING THE HUMIDIFIERTAOTRONICS TT-AH044 -Ultrasonic- Cool Mist
-Humidifier- FIG 5

  1. DO NOT plug the unit with wet hands.
  2. DO NOT use your hand or any other object to cover the nozzle while the unit is on to avoid damaging the product or causing injury.TAOTRONICS TT-AH044 -Ultrasonic- Cool Mist -Humidifier- FIG 6

AFTER USING THE HUMIDIFIERTAOTRONICS TT-AH044 -Ultrasonic- Cool Mist
-Humidifier- FIG 7

PACKAGE CONTENTS

  • 1 x TaoTronics Humidifier (Model: TT-AH044)
  • 1 x Cleaning Brush
  • 1 x Dustproof Sponge
  • 1 x Thank You Card
  • 1 x User Guide

SPECIFICATIONS

TAOTRONICS TT-AH044 -Ultrasonic- Cool Mist -Humidifier-
FIG 16TAOTRONICS TT-AH044 -Ultrasonic-
Cool Mist -Humidifier- FIG 8

PRODUCT DIAGRAM

  1. Nozzle
  2. Water Tank
  3. Water Level Window
  4. Tank Cap
  5. Water Inlet
  6. Handle
  7. LED Display
  8. Control Buttons
  9. Base
  10. Night Light
  11. Floater
  12. Air Outlet
  13. Tank Light
  14.  Water Reservoir
  15. Atomizer
  16. Dustproof Sponge
  17.  Air Inlet

OPERATIONS AND FUNCTIONS

TAOTRONICS TT-AH044 -Ultrasonic- Cool Mist
-Humidifier- FIG 9

OPERATIONS AND FUNCTIONS

TAOTRONICS TT-AH044 -Ultrasonic- Cool Mist
-Humidifier- FIG 10

OPERATIONS AND FUNCTIONS

  • Connect the humidifier to a power source, the unit is in Standby mode now with the LED display showing the current humidity level.
  • If no operation is done within 5 seconds under Standby mode, the LED display will turn off automatically.
  • When there is not enough water inside the water reservoir, the humidifier will stop misting and Low Water Protection will be activated with 0 light­ing up on the display.

Power Button

  •  Press the Power Button once to turn the humidifier ON with default settings: medium mist (200ml/h, 4 lines) & tank light on.
  • Press it again to turn the humidifier OFF (mist off & tank light off). The fan will continue working for 3 minutes to dry the mist tube.

Mist Adjustment

When the unit is on, press the Mist Button to cycle through Medium (4 lines)-> High (6 lines)-> Low (2 lines) mist levels.

Timer Setting

  • Press the Timer Button to set the timer from 01 to 12 hours by 1 hour increments, the timer will flash three times to confirm your setting.
  • Once set, the LED display will show the countdown timer and the current humidity level. When time is up, the unit will automatically turn off.
  • To cancel Timer setting, press and hold the Timer Button for 1.5 seconds or adjust the timer setting to 00.

Humidity Setting

  • Press the Humidistat Button to set the humidity level from 30% to 95% in .  501 10 increments, t h e set h umI .d. Ity I eve I wI ·11 fl as h t h ree . times to con f· Irm your setting.
  • When the preset humidity level is reached, the unit will stop misting with the whitevturning green.
  • To cancel Humidity setting, press and hold the Humidistat Button for 1.5 seconds. The most comfortable environmental humidity is between 40%-60%. Please adjust the mist as needed.

Sleep Mode

  • When the mist is on, press the Sleep Button once to turn on the Sleep mode. All the indicators on the LED display will turn off except the Sleep indicator. If no operation is done within 3 seconds under Sleep mode, the sleep indicator will turn off automatically.
  • Press any button (except the Light Button) to wake up Sleep Mode and LED display. All the other buttons remain functional. If no operation is done within 3 seconds, the LED display will turn off automatically.
  • Press it again to exit Sleep mode. The sleep indicator will turn off and the LED display will remain on.
  • When there is not enough water inside the water reservoir under Sleep Mode, the humidifier and the LED display will turn off automatically.
  • When the Sleep mode is turned on under night light on, all the indicators on the LED display and the night light will turn off except the Sleep indicator. You can press the Light Button again to turn the night light on.

Light Button (Night Light & Tank Light) 

  • Night Light: Press the Light Button to turn on/ off the night light (default: OFF).
  • Tank Light: Press and hold the Light Button for 1.5 seconds to turn on/ off the tank light (default: ON).
  • The night light is separately controlled. You can turn on/ off the night light when the unit is connected to power.

Low Water Protection

  • When there is not enough water inside the water reservoir, the humidi-fier will stop misting and Low Water Protection will be activated with the icon lighting up on the display. It is designed for safety to prevent the humidifier from possibly overheating and damaging the atomizer.
  • The humidifier cannot be started under low water status.

Memory Function
If power is not disconnected, the humidifier will always remember your last settings (mist level, humidity & night light) once you turn it on again.

CLEANING AND MAINTENANCE

Caution

  1.  DO NOT submerge the base in water.
  2.  Make sure water does not enter the base through the air outlet, air inlet, or the control buttons and LED display.
  3. DO NOT wash any part of this humidifier in dish washer which will damage the humidifier and void the warranty.

Daily Maintenance
Turn off the humidifier, unplug it from the power source. Drain water from the tank, reservoir and base.
Weekly Maintenance

  1. To properly clean your humidifier, we recommend you to remove scale and disinfect the humidifier separately.
  2. DO NOT mix vinegar and bleach solutions together. Do not use more than 1 tsp. of bleach per gallon of water to avoid damaging your humidifier.
  3. Please make sure the rubber ring & rubber cap & spring on the tank cap is installed properly after cleaning to avoid water leakage. For more detailed information, please refer to the Troubleshooting Guide.

Scale Removal InstructionsTAOTRONICS TT-AH044 -Ultrasonic- Cool Mist
-Humidifier- FIG 13

  1. Turn off and unplug the humidifier. Remove the nozzle.
  2. Remove the water tank from the base. Remove the tank cap. Make sure that the sealing ring does not come off. Drain water from the water tank and base. Remove any accessories and set aside.
  3.  Fill the water tank half full. Add in 1 teaspoon of undiluted distilled white vinegar. Attach the tank cap and shake for 15 seconds.
  4. Place the tank onto the base. The vinegar solution will enter the water reservoir to loosen mineral buildup (scale) on the atomizer, water floater and the bottom of the water tank. Set still for 15- 20 minutes.
  5. Uncap the tank cap and drain the solution. Wipe the atomizer and floater with a soft cloth to remove loosened mineral deposits.
  6.  Rinse both the water reservoir and water tank until the smell of vinegar (for scale removal) or bleach solution (for disinfecting, see below) is gone.

Disinfecting Instructions

  1. Follow steps 1-2 of the previous section on scale removal.
  2. Fill the water tank half full. Add in½ tsp of bleach. Place the tank cap back on. Swish the solution around in tank. Place the tank on the base. The bleach solution will enter and disinfect the water reservoir as well as the other components. Set still for 15-20 minutes.
  3. Follow steps 4-6 of the previous section on scale removal to complete disinfecting the humidifier.

Clean the Dustproof SpongeTAOTRONICS TT-AH044 -Ultrasonic- Cool Mist
-Humidifier- FIG 14

Clean the dustproof sponge (at the back of base) with water or detergent once a month. Put it back in place after cleaning.

End-Of-Season Care and Storage

  1. Follow the cleaning instructions when the humidifier will not be used for at least one week, or at the end of the season. Remove any accessories used with the humidifier and allow the humidifier and accessories to dry completely before storing.
  2. DO NOT store with water inside the base, water reservoir, or tank.
  3. Pack the unit safely and store in a cool, dry location.

TROUBLESHOOTING GUIDE

  1. If the information listed in the troubleshooting guide can’t solve your problem, please email us for help.
  2. Failure to keep this unit clean from mineral deposits may affect operation of this unit.
  3. Customer failure to follow these instructions may void the warranty.TAOTRONICS TT-AH044 -Ultrasonic- Cool Mist -Humidifier- FIG 15TAOTRONICS TT-AH044 -Ultrasonic- Cool Mist -Humidifier- FIG 17

LED display is on, no mist or little mist is produced

| Not enough water inside the

tank

| Refill and reinstall the water

tank

---|---|---
Mist level is set too low| Adjust to maximum mist

Preset humidity is set too low

| Check if current humidity is higher than preset humidity, reset humidity to a higher

level

The base might be overfilled

| Remove the tank, empty the base & replace the filled tank on the empty

base

Mineral buildup on atomizer

| Feel if air comes out from the the nozzle, if yes, then clean water scale on the

atomizer as instructed

Tank leakage

|

Tank may be damaged

| Check for possible cracks in

the tank, replace if necessary

Tank cap is not tightened securely|

Tighten the tank cap

Rubber ring was not installed on tank cap

| Check the tank cap for rubber ring, rubber cap and spring, contact us if

any is missing

Spring stuck

| Ensure the        spring is secured properly to the tank allowing water to pass through to the base

Mist height is low, damping surrounding desk or floor. Condensation forms around humidifier or on windows and walls

|

Mist level is set too high for the room size

| 1. Check if the room is too humid, adjust to lower mist, 40%-60% works best

2. Open door and windows,

or change to a larger room

Air inlet is blocked

| Humidifier should be placed on a hard flat surface, 2 feet above the floor, 12 inches away from the wall. Point Mist Outlet

away from wall or window

Low indoor temperature leads to liquefaction| Raise the room temperature to 25°C/77°F

Poor humidification

|

Mist level is set too low for the room size

| 1-1. Adjust to maximum mist

1-2. Close door or windows to reduce air ventilation, or change to a smaller room

---|---|---

Air inlet is blocked

| Humidifier should be placed on a hard flat surface, 2 feet above the floor, 12 inches away from

the wall

Low indoor temperature leads to liquefaction| Raise the room temperature to 25°C/77°F

White Dust Appears/ Black coating in the base flakes off

|

Tap water may contain too much minerals

| Replace with filtered or distilled water or use with a TaoTronics Demineralization Cartridge

Strange Odor

|

Unit needs to be cleaned

| Clean the humidifier as instructed
Leave the empty water tank open in a cool place for 12 hours without the water tank cap attached

Strange water noise

| Water is going down to the water reservoir| This is normal while it is working

Humidifier is getting too hot

|

Unit works for too long

| Power off and place in a well-ventilated place for 10 minutes

WARRANTY

This product is covered with TaoTronics product and labor warranty for 12 months from the date of its original purchase. You will be given a warranty extension of 18 months if the product is registered on our website (www.taotronics.com). Any defective part will be, at the discretion of SUNVALLEYTEK INTERNATIONAL INC., repaired or replaced at no charge if the appliance has not been tampered with and has been used according to these printed directions. If any problems occur, please contact TaoTronics support ([email protected]) immediately to launch a warranty claim. Specify model number and your Amazon order number. Our Consumer Service Representative will respond within 1 business day, advise you how to correct the problem yourself, or instruct you on how to return the defective unit back to us for repair or replacement. We can only provide after sales service for products that are sold by TaoTronics or TaoTronics authorized retailers and distributors. If you have purchased your unit from a different place, please contact your seller for return and warranty issues.

CONTACT/ TAOTRONICS CUSTOMER CARE

PLEASE CONTACT US BEFORE RETURNING THIS PRODUCT TO THE STORE. EMAIL TAOTRONICS CUSTOMER CARE FOR PROBLEMS AND QUESTIONS. WE WILL RESPOND WITHIN 1 BUSINESS DAY. E-mail: [email protected] Website: www.taotronics.com

FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

WEEE Compliance
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

TaoTronics User Manuals

Related Manuals