ZEVNI A04644 24 Inch Wide Gold and Black LED Chandelier User Manual
- June 3, 2024
- ZEVNI
Table of Contents
ZEVNI A04644 24 Inch Wide Gold and Black LED Chandelier
Item Number: A04644
WARNING (To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
-
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position. -
Place the wall switch in the “OFF” position.
-
-
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is 38W.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
TOOLS REQUIRED (NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools as
below picture
PARTS TYPE & QTY INCLUDING
- Mounting plate (1)
- Green ground screw (1)
- Canopy (1)
- Stud (2)
- Lock nut (2)
- Cable (1)
- Steel wire (1)
- Tube (1)
- Cover (1)
- Arms assembly (L)
- Arm (6)
ACCESSORIES & QTY ENCLOSED
- Plastic wire connector (3)
- Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
-
Unscrew studs (F) from canopy (E) then remove mounting plate (B).
-
Adjust arms (M) to the proper position or an equal angle.
-
Carefully slide tube (J) and cover (K) along wires. Place cover (K) on the top of arms assembly (L) and secure it with tube (J). Hand tighten till snug.
-
Attach mounting plate (B) to the outlet box with mounting screws (D).
-
Make wire connections Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box. -
Raise canopy (E) to the ceiling and secure canopy (E) in place by threading studs (F) into mounting plate (B) and canopy (E).
-
To adjust the hanging height of the fixture: To adjust the length of cable (H) and steel wire (I):
- Press down and hold lock nuts (G) by hand;
- Pull or push cable (H) and steel wire (I) in and out of canopy (E) to increase or decrease the hanging height.
-
Check everything is already installed properly, then you could turn on the light. Enjoy!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>