Amantii Lynwood Series Freestanding Cast Iron Electric Fireplace Instruction Manual

Amantii Lynwood Series Freestanding Cast Iron Electric Fireplace

Specifications

• Description: Virtus 50 Free Standing Appliance
• Voltage: 120V AC 60Hz
• Watts: 1465W Max
• Heater: NO HEATER MOTOR HEATER (18.5W)
• Appliance Width: 23″ or 58.6 cm
• Appliance Height: 28 1/4″ or 71.7 cm
• Appliance Depth: 17 1/2″ or 44.3 cm
• Gross Weight: 123.5 lbs or 56 kg
• Plug Location: Left side
• Cord Length: 70 7/8″ or 180 cm
• BTU: 5000

SAFETY INFORMATION

WARNING:  For your safety, always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this appliance.

INSTALLER: LEAVE THE OWNER’S MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THE OWNER’S MANUAL FOR FUTURE REFERENCE.
WARNING: This product can expose you to chemicals including Lead in the wiring, which is [are] known to the State of California to cause birth defects or other reproductive harm. For more information visit: www.p65warnings.ca.gov

Please read and carefully follow all instructions found in this manual. Please pay special attention to the safety instructions provided in this manual. The instructions included here will ensure that you have many years of dependable and enjoyable service from your Amantii product.

IMPORTANT INSTRUCTIONS

PLEASE RETAIN THIS USER GUIDE FOR FUTURE REFERENCE
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using this fireplace
2. The fireplace is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible material such as furniture, cushions, bedding, paper, clothes, and curtains at least 3 feet from the front of the unit
3. Extreme caution is necessary when any heater is used near children and whenever the unit is left operating and unattended
4. Do not operate a fireplace with a damaged cord or plug, or if the heater has malfunctioned, the fireplace has dropped or damaged in any manner
5. Not all fireplaces are suitable for use in bathrooms or laundry facilities. Please consult with individual product literature to confirm suitability
6. Do not run the cord under the carpeting. Do not cover the cord with throw rugs, runners, or the like. Arrange the cord away from traffic area and where it will not be tripped over
7. Do not modify this fireplace. Use it as described in the manual. Any other use not recommended by the manufacturer may cause fire, shock, or injury to persons
8. Do not use this heater with a programmer, timer, separate remote-control system, or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly
9. Disconnect all power supplies before cleaning, maintaining, or relocating the fireplace
10. Keep the heater clean. Do not allow any objects to enter any ventilation or exhaust opening as this may cause electric shock, fire, or damage to the heater
11. Do not immerse the cord, plug, or any part of the appliance in water or any other liquid
12. To avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device

CAUTION: Procedures and techniques, which, if not carefully followed, will result in damage to the equipment.
WARNING : Procedures and techniques, which, if not carefully followed, will expose the user to the risk of fire, serious injury, illness, or death.

UNPACKING AND TESTING APPLIANCE

• Carefully remove the appliance from the box.
• Before installing the appliance, test to make sure the appliance operates properly by plugging the power supply cord into a conveniently located 120-volt grounded outlet.
• Test all aspects of its operation (manual switches, remote, and heater) to make sure all components operate correctly.
• As with most electronic devices, your electric fireplace has been designed to operate at temperatures between 5 ℃ (41℉) and 35℃ (95℉). During the cold winter months, allow the fireplace to reach room temperature before turning it on.

NOTE: There may be a trace of odor during the first few minutes of initial use. This is harmless, normal, and will never occur again.

GROUNDING APPLIANCE

This appliance is for use on 120 volts. The cord has a plug as shown in (A). An adapter as shown in (C) is available for connecting three-blade grounding- type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.
To disconnect the appliance, turn the controls off, then remove the plug from the outlet.

CHOOSING A LOCATION FOR THE FIREPLACE
Plan where to place and frame the fireplace. Before installation consider the following:

1. The location of the fireplace must allow for wall and ceiling clearances.
2. Consider a location where the fireplace screen will not be exposed to direct sunlight from windows or doors.
3. A 15 ampere, 120 Volt, 60 Hz branch circuit with proper ground must be available at the location. A dedicated branch circuit should be provided to prevent circuit breakers from tripping or fuses from blowing.

VIRTUS 50

This appliance has been tested by the UL Standard 2021 for fixed and location- dedicated electric room appliances in the United States and Canada. If you need assistance during installation, please contact your local dealer.
NOTE: This appliance must be electrically wired and grounded by local codes. In the absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI/NFPA 70 National Electrical Code in the United States.

VIRTUS 70

This appliance has been tested by the UL Standard 2021 for fixed and location- dedicated electric room appliances in the United States and Canada. If you need assistance during installation, please contact your local dealer.
NOTE : This appliance must be electrically wired and grounded by local codes. In the absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI/NFPA 70 National Electrical Code in the United States.

MEDIA OPTIONS

Your fireplace shipped with DESIGN MEDIA- BIRCH-10PCE

MEDIA INSTALLATION

• STEP 1: Unplug the unit and make sure the controls are switched off.
• STEP 2: Take off the top cover.
• STEP 3: Pull the front door up and take it off.
• STEP 4 : Now you can decorate your fireplace
• STEP 5 : After the media has been installed, reinstall the front door and top cover

OPERATION

The fireplace can be operated by the switches located on the left front of the fireplace unit or by remote control (included).

MANUAL OPERATION

1. The main power ON/OFF switch is in position 0, and the fireplace is OFF.

2. When the main power ON/OFF switch is at position I, the fireplace is ready to use.

3. Press the button repeatedly to set the heater to the desired heat setting. The heater indicator
   LED will glow which shows the current heater settings.

4. a) RED 1465W HEAT OUTPUT

5. b) BLUE 750W HEAT OUTPUT

6. C) PURPLE AUTO MODE
   AUTO MODE
   Under this mode, the heater will automatically turn ON at a high heat setting of 1465W heat output when
   the room temperature drops below 22°C(72°F). When the room temperature is between 22-
   25°C (72-77°F) the heater output will switch to low heat setting 750W. When the room temperature
   goes above 25°C(77°F’) the heater will be turned off and the cycle will continue. The LED indicator
   will be PURPLE under this mode.

7. Flame effect : Press the button marked to adjust the flame brightness. The flame brightness will cycle through -Medium -OFF.

8. Mood light effect: Press the button marked to change the mood light color.

NOTE: If operated at the Low heat setting, the fireplace will not provide as much heat as in the High setting, however, the low setting will not require as much electrical power. To avoid overloading the circuit, do not plug the fireplace into a circuit that already has other appliances working connected. When the fireplace is not in use, switch off and unplug.

SAFETY CUT-OFF

• This appliance is fitted with a safety cut-off which will operate if the fireplace overheats (eg. Due to blocked air vents). For safety reasons, the fireplace will NOT automatically reset.
• To reset the appliance, disconnect the appliance from the main supply for at least 10 minutes.
• Reconnect the supply to the main and switch on the appliance.

REMOTE CONTROL OPERATION

For the remote to function make sure the heater is plugged in and the main power switch located on the bottom left-hand side is at position I.
When operating the remote make sure you point the remote to the center of the fireplace and make sure each time you press the button the buzzer inside the unit will beep once. It takes some time for the receiver to respond to the transmitter. Do not PRESS the buttons more than once within two seconds for correct operation. Power on the button : The power-on button at the top left corner of the remote is the main ON/OFF power button. This will turn off all the functions and the fireplace will be in standby mode.

• DISPLAY ON/OFF button: Switches the fireplace flame and tray light On and Off. It will store the last setting.
• DISPLAY BLUE button: Adjusts the blue color and brightness of the flame and tray.
• DISPLAY YELLOW button : Adjusts the yellow color and brightness of the flame and tray.
• DISPLAY ORANGE button: Adjusts the orange color and brightness of the flame and tray.
• MOOD LIGHT ON/OFF button: Switches the mood light On and Off.
• ADJUST button: Switches the color of the mood light.
• FLASH button: Switches the mood light into flash mode. This cycles through all mood light colors.
• HEATER ON/OFF button: Turns the heater On and Off. It will store the last setting.
• HIGH button: Press the high button to switch the heater to high heat setting 1465W.
• LOW button: Press the low button to switch the heater to low heat setting 750W.
• TEMP button: Press the TEMP button to switch the heater to AUTO mode. Under this mode, the heater will operate as explained in the manual operation.

REPLACEMENT PARTS

This list contains replacement parts

8

| 601136B| LED STRIP|
601141B| LED STRIP|
9| 601097B| CIRCUIT BOARD| 1

11

|

602067D

| BLOWER AND HEATER

ASSEMBLY(FRT45-187)

|

1

12| 10105063| REMOTE CONTROL| 1
13| 601036| CONTROL PANEL| 1
14| 10101225| FLAME MOTOR| 1
15| 10104002| SWITCH| 1

NOTE: The remote control, control panel, flame motor, and switch are not shown in the exploded view.

EXPLODED VIEW

Wiring Diagram

TROUBLESHOOTING

if

necessary.

The back black cloth is falling off

and rolled up in the flicker

| Change a flicker and back black cloth.
The Ember     bed     is     not

glowing or dimming

| Ember LEDs are burnt out| Inspect the ember bed LEDs and

replace them if necessary.

The appliance turns off and will not turn on| The appliance has overheated and the safety device has caused the

thermal switch to disconnect

| Turn   off   the    main   switch,           allow the appliance to cool for 10 minutes, then

turn it on.

House

tripped

| circuit| breaker| has| Reset the house circuit breaker.
The appliance’s fuse has blown| Replace the fuse.
The appliance will not come on when the switch is flipped to ON| The appliance is not plugged into an electrical outlet| Check the plug and plug in.
The appliance has overheated and

safety device has caused the thermal switch to disconnect

| Turn   off   the    main   switch,    allow

appliance to cool for 10 minutes, then turn it on.

The circuit board is burnt out| Inspect the circuit board and replace

it if necessary.

No warm air coming out

of appliance

| The heater is burnt out| Inspect     the    burner     and     heater

assembly and replace it if necessary.

Flame sputters| The flame motor is defective.| Call a qualified service technician and

replace the flame motor.

Remote    Control does not work.| Low batteries.

Unit switch in “O” position.

| Replace   AAA batteries in the control.

Turn the switch in the “I” position.

| remote
The flame is fixed.| The wiring may be loose or the

flame motor may be defective.

|

SERVICE HISTORY

This heater must be serviced annually depending on usage.

Date| Dealer

Name

| Service Technician

Name

| Service Performed| Special Concerns
---|---|---|---|---

WARRANTY

WARRANTY FOR PRODUCTS MANUFACTURED AFTER JANUARY 1st, 2016
Amantii Imports Corp. (“Amantii”) warrants that your newly purchased Amantii electric fireplace is free from manufacturing and material defects for two (2) years from the date of the first purchase, subject to the conditions and limitations contained below.

Warranty Application & Exclusions

• This limited warranty applies to your newly purchased Amantii electric fireplace; the limited warranty’s application is limited to purchases made in any province of Canada or any of the 52 States of the United States of America, including the District of
• Columbia. Only the original purchaser of the product is eligible for coverage under this limited warranty; the warranty is not transferable.
• Products excluded from this limited warranty
• Light bulbs are not covered by this limited warranty and are the sole responsibility of the owner/purchaser. Amantii does not cover service or labor charges.

Warranty Coverage and Term

• Products covered by this limited warranty have been tested and inspected before shipment and, subject to the provisions of this warranty,
• Amantii warrants such products to be free from defects in material and workmanship for two (2) years from the date of the first purchase of such products.
• The limited two (2) year warranty period for products also applies to any implied warranties that may exist under applicable law. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to the purchaser.
• All other warranties expressed or implied concerning the product, its components and accessories, or any obligation/liabilities on the part of Amantii are hereby expressly excluded.

Limitations to Coverage Under Limited Warranty
This limited warranty does not apply to products that have been repaired, except by Amantii or its authorized service representatives, or otherwise altered. This limited warranty further does not apply to defects resulting from misuse, abuse, accident, neglect, incorrect installation, improper maintenance or handling, or operation with an incorrect power source. Products made by other manufacturers, sold with the product or thereafter, are not covered by this limited warranty. The use of unauthorized components will render this warranty null and void.

Panorama Outdoor Units
All Panorama units that are installed outdoors or in moisture-intense conditions must use the stainless steel cover. Proof of purchase of the cover is required for any warranty claims.

Defects
Defects must be brought to the attention of the selling dealer. Please have your proof of purchase, catalog/model, and serial numbers available when contacting the dealer; any service under the limited warranty requires proof of purchase of the product. Should a product or part covered by this limited warranty be proven to be defective, in material or workmanship, and during the two (2) year limited warranty period,
Amantii will replace such defective products or parts without charge. If Amantii is unable to replace such product, or if replacement is not commercially practicable or cannot be timely done, in its sole discretion Amantii may, instead of replacement, choose to refund the purchase price for such product or part. Amantii does not cover labor or service charges to replace said parts.

Limitations
In no event will Amantii, including without limitation any of its directors, officers, shareholders, employees, consultants, agents, heirs, executors, administrators and assigns, be liable to the purchaser or any third party, whether in contract, in tort, or on any other basis for any indirect, special, punitive, exemplary, consequential, or incidental loss, cost or damage arising out of or in connection with the sale, maintenance, use or inability to use the product, even if Amantii, including without limitation any of its directors, officers, shareholders, employees, consultants, agents, heirs, executors, administrators and assigns, have been advised of the possibility of such losses, costs or damages, or if such losses, costs or damages are foreseeable. In no event will Amantii, including without limitation any of its directors, officers, shareholders, employees, consultants, agents, heirs, executors, administrators, and assigns, be liable for any direct losses, costs, or damages that exceed the purchase price of the product.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to the purchaser.

Application of Provincial and State Law
This limited warranty gives you specific legal rights, and you may also have other rights that vary from jurisdiction to jurisdiction. The provisions of the United Nations Convention on Contracts for the Sale of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty.

General styles and products.
Amantii reserves the right to make changes at any time without notice, in design, material, specifications, prices and the right to discontinue

MORE INFORMATION

• Amantii Electric Fireplaces
• 502-1027 Davie Street
• Vancouver, BC V6E4L2

www.amantii.com

Frequently Asked Questions

• Q: Can this appliance be used with a different voltage?
  • A: No, this appliance is designed for use with 120V AC 60Hz only. Using a different voltage may damage the unit.
• Q: What should I do if the appliance is not functioning properly?
  • A: If you encounter any issues with the appliance, refer to the troubleshooting section of the user manual or contact your local dealer for assistance.
• Q: How do I clean and maintain the fireplace?
  • A: Regularly clean the exterior of the appliance with a soft cloth and follow maintenance instructions provided in the manual to ensure optimal performance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>