BRAYER BR4124 Handle Garment Steamer Instruction Manual

: June 3, 2024
: BRAYER

Table of Contents

DESCRIPTION
SAFETY MEASURES AND OPERATION RECOMMENDATIONS
BEFORE THE FIRST USE
STEAMER OPERATION
USING THE BRUSH ATTACHMENT
CLEANING AND CARE
Troubles and troubleshooting
TECHNICAL SPECIFICATIONS
Documents / Resources

BR4124 Handle Garment Steamer
Instruction Manual BRAYER BR4124 Handle Garment Steamer - Qr
Code BRAYER is an Austrian consumer electronics brand.
The importer in Russia – “Granted” LLC.

The garment steamer is intended for the careful smoothing of folds on clothes or furniture.

DESCRIPTION

BRAYER BR4124 Handle Garment Steamer - DESCRIPTION

Removable water tank
Water inlet
Power plug
Steam supply on button
Operating surface with steam release openings
Body
Handle
Brush attachment

SAFETY MEASURES AND OPERATION RECOMMENDATIONS

Read the operation instructions carefully before using the garment steamer, after reading keep them for future reference.

Use the unit for its intended purpose only, as it is stated in this manual.
Mishandling the unit can lead to its breakage and cause harm to the user or damage to the user’s property, which is not covered by warranty.
Make sure that the operating voltage of the unit indicated on the label corresponds to your home mains voltage.
The power cord is equipped with a «euro-plug»; insert it into a socket that has a reliable grounding connection. In the case of a short circuit, the grounding reduces the risk of electric shock.
Contact an electrical technician if you are not sure that your sockets are installed properly and grounded.
To avoid fire, do not use adapters for connecting the unit to the mains.
Do not touch the unit body, the power cord, and the power plug with wet hands.
Do not switch the garment steamer on if the water tank is empty. Switch the unit off and unplug it when the water tank becomes empty.
Never leave the unit connected to the mains unattended.
Do not use the unit outdoors or in the bathrooms.
It is not recommended to use the unit during lightning storms.
Protect the unit from impacts, falling, vibrations, and other mechanical stress.
Do not use the unit near heating appliances, heat sources, or open flames.
Do not use the unit in proximity to the kitchen sink, bathrooms, swimming pools, or other containers filled with water.
If the unit is dropped into water, unplug it immediately, and only then you can take the unit out of the water. Apply to the authorized service center for testing or repairing the unit.
Do not use the unit in places where aerosols are used or sprayed, and in proximity to highly inflammable liquids, do not use the unit in the places where such liquids are stored.
Place the garment steamer vertically on a flat dry moisture- and heat-resistant surface, do not place it horizontally, and do not turn it over.
Use only the attachment supplied with the unit.
Before using the unit, make sure that the attachment is set and fixed properly.
During the operation hold the garment steamer vertically, do not turn it over.
Fill the tank with water additionally cleaned it with a domestic filter. Do not use carbonated water or any perfume additives.
Ensure that the water level is not above the maximal mark «MAX». If the water level exceeds the maximal mark, water may splash out of the garment steamer.
Do not block and do not insert any foreign objects into the steam release openings.
During the operation the upper part of the garment steamer body becomes hot. To avoid getting burns, hold the garment steamer by the handle at the same level as the steam supply on the button.
Avoid getting burned by hot steam.
Never steam clothes on a person, always use a hanger.
Never direct operating steamer onto people, animals, and plants as well as onto furniture, electric appliances, books, and any other objects that can be damaged by hot steam. The garment steamer should be at least 20 cm away from any interior objects.
Do not use the power cord as a handle for carrying the garment steamer, carry it by the handle.
Unplug the unit after usage or before cleaning.
Switch the garment steamer off and unplug the power cord plug from the main socket.
When unplugging the unit, hold the power plug and carefully remove it from the mains socket, do not pull the power cord, as this can lead to its damage and cause a short circuit.
For children, for safety reasons do not leave polyethylene bags used as packaging unattended.
Attention! Do not allow children to play with polyethylene bags or packaging film. The danger of suffocation!
The unit is not intended for use by children.
Do not leave children unattended to prevent using the unit as a toy.
Do not allow children to touch the operating surface, the unit body, the power cord, or the power plug during the operation of the unit.
Be especially careful if children or disabled persons are near the operating unit.
During the unit operation and breaks between operation cycles, place the unit out of reach of children.
The unit is not intended for use by persons (including children) with physical, sensory, or mental disabilities, with no experience or knowledge, if they are not under supervision, or if they have not been instructed as to how to use the unit by the person responsible for their safety.
From time to time check the power cord integrity.
If the power cord is damaged, it should be replaced by the manufacturer, maintenance service, or similarly qualified personnel to avoid danger.
Do not repair the unit by yourself. Do not disassemble the unit by yourself, if any malfunction is detected, and after the unit was dropped, unplug it and apply it to the service center.
To avoid damages, transport the unit in the original package.
Keep the unit in a dry cool place out of reach of children and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE UNIT FOR COMMERCIAL OR LABORATORY PURPOSES.

BEFORE THE FIRST USE

After the unit’s transportation or storage at negative temperature, unpack it and wait for at least 3 hours before using it.

Unpack the unit and remove all the packaging materials.
If there is a protective film on the operating surface (5), remove it.
Keep the original package.
Read the safety measures and operating recommendations.
Check the delivery set.
Examine the unit for damages, in case of damage do not plug it into the mains.
Make sure that specified specifications of power supply voltage of the unit correspond to the specifications of your mains. When using the unit in the mains with 60 Hz frequency, the unit does not need any additional settings.
Wipe the garment steamer body with a slightly damp cloth and then wipe it dry.

GARMENT STEAMER PURPOSE

The garment steamer can be used for the careful smoothing of folds on clothes or furniture.
If you have doubts about steaming any certain kind of fabric or clothes, you should follow the recommendations on the product label.
If the item label is marked with the « » symbol, do not iron the item.
If the item label is marked with the « » symbol, do not steam the item.
If no such information is available, try to steam the fabric on the reverse side.
When steaming such fabrics as silk or corduroy, keep the garment steamer at some distance from the fabric.
Use the brush attachment (8) to remove lint or threads from the fabric.

STEAMER OPERATION

WATER SELECTION

Fill the water tank (1) with tap water. If tap water is hard, we recommend mixing it with distilled water in proportion 1:1. If tap water is too hard, mix it with distilled water in proportion 1:2 or use distilled water only.
ATTENTION! Before detaching the water tank (1), make sure that the power plug (3) is not inserted into the main socket.
Turn the water tank (1) towards the « » symbol.
Fill the water tank (1) with water by pouring it into the water inlet (2) not exceeding the MAX mark.
Maximal water tank (1) capacity is 300 ml.
Do not fill the tank (1) with carbonated water, perfume additives, vinegar, chemical agents, etc.
Install the water tank (1) back to its place and turn it towards the « » symbol, make sure that the water tank (1) is fixed properly.
ATTENTION! Do not plug the garment steamer in if the water tank (1) is empty.
Make sure that the steam supply button (4) is set to the « » position.
Place the garment steamer on a flat and steady surface.
Connect the power plug (3) to the main socket. Wait for some time (from 3 to 5 minutes) necessary for the normal generation of steam.
Take the garment steamer by the handle (7) on the same level as the steam supply on the button (4).
To turn the steam supply on, press and hold the button (4) in the « » position.
To switch the steam supply off release the button (4).
Continuous steam supply is carried out by setting the steam supply button (4) to the « » position.
For maximum steam supply, press and hold the lower part of the « » button (4).
Before general use of the garment steamer clean the steam chamber. To do this, direct the outgoing steam to a piece of cloth, for instance, try to smooth out a kitchen towel.
If during the operation the water tank (1) becomes empty, switch the garment steamer off before removing tank (1) and refilling it with water. To do this, disconnect the power plug (3) from the main socket.
After the unit operation, remove the power plug (3) from the main socket and let the garment steamer cool down.

Note: when the unit is switched on for the first time, the foreign smell is possible, this is normal and is not covered by warranty.

USING THE BRUSH ATTACHMENT

ATTENTION! Before installing the brush attachment (8), make sure that the power plug (8) is not inserted into the main socket.

Place the brush attachment (8) on the operating surface (5). Make sure the brush attachment (8) is fixed properly.
Make sure that there is water in the water tank (1), and fill the water tank (1) if necessary.
Place the garment steamer on the base on a flat and steady surface.
Make sure that the steam supply button (4) is set to the « » position.
Connect the power plug (3) to the main socket. Wait for some time (from 3 to 5 minutes) necessary for the normal generation of steam.
Take the garment steamer by the handle (7) on the same level as the steam supply on the button (4).
Hang the clothes on a hanger.
Note: never steam clothes on a person as the outgoing steam temperature is very high, use a hanger only.
To turn the steam supply on press and hold the button (4) in the « » position.
To switch the steam supply off release the button (4).
Continuous steam supply is carried out by setting the steam supply button (4) to the « » position.
For maximum steam supply press and hold the lower part of the « » button (4).
Slowly move the brush attachment (8) along the fabric, and smooth out the fabric with your free hand.
Notes:
– during operation, hold the garment steamer vertically and do not turn it over;
– during the garment steamer operation the upper part of the body (6) becomes very hot. Be careful and do not touch hot parts of the unit body (6) and the operating surface (5);
– after steaming the clothes may need some time to dry, leave them on the hanger.
After the unit operation, remove the power plug (3) from the main socket and let the garment steamer cool down.
Detach the brush attachment (8).
Remove the water tank (1) and pour out the remaining water, and install the water tank (1) back in its place.

CLEANING AND CARE

Disconnect the power plug (3) from the main socket and wait until the garment steamer cools down completely.
Remove the water tank (1) and pour out the remaining water, and install the water tank (1) back in its place.
Clean the garment steamer body (6) and the operating surface with the steam release openings (5) with a slightly damp cloth, and then wipe dry.
You can remove the mineral deposit from the operating surface (5) with a cloth soaked in vinegar water solution.
Remove the brush attachment (8) and wash it under a water jet.
Do not use abrasive cleaners and solvents to clean the garment steamer.
Do not immerse the garment steamer, the power cord, and the power plug (3) in water or any other liquids.

STORAGE

Unplug the garment steamer and wait till it cools down completely.
Clean the garment steamer.
Keep the unit in a dry cool place out of reach of children and disabled persons.

Troubles and troubleshooting

Malfunction	Possible reason	Solution
Small amount or absence of outgoing steam	– The garment steamer is not

connected to the socket
– You do not press the steam supply on button completely
– There is not enough water in the tank| – Insert the power plug into the mains socket
– Press the steam supply on button until bumping
– Unplug the unit, remove the water tank and fill it with water, then install
the water tank back to its place
When the steam supply is switched on, water leaks from the steam release openings| The garment steamer is not hot enough| Let the garment steamer heat up a little longer before the use
Water leaks from the steam release openings| During heating, the pressure in the steam chamber increases, and water drops can appear in the steam release openings| It is normal
The sound of boiling
water inside the
garment steamer
and slight vibration
of the garment
steamer body| – Boiling of water in the steam chamber is accompanied by a corresponding sound – The operation of the water pump is accompanied by a slight vibration| It is normal

DELIVERY SET

Garment steamer – 1 pc.
Brush attachment – 1 pc.
Manual – 1 pc.

TECHNICAL SPECIFICATIONS

Power supply: 220-240 V, ~ 50/60 Hz
Rated input power: 1240-1470 W
Water tank capacity: 300 ml
Steam release: 20 g/min

RECYCLING
To prevent possible damage to the environment or harm to the health of people uncontrolled waste disposal, after expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, take the unit and the batteries to specialized stations for further recycling.
The waste generated during the disposal of products is subject to mandatory collection and consequent disposal in the prescribed manner.
For further information about recycling of this product apply to a local municipal administration, a householdwaste disposal service or to the shop where you purchased this product.
The manufacturer reserves the right to change the design, structure and specifications not affecting general principles of the unit operation, without prior notice.
The unit operating life is 3 years
The manufacturing date is specified in the serial number.
In case of any malfunctions, it is necessary to apply promptly to the authorized service center.

brayer.ru
Produced for «Ruste GmbH»,
Berggasse 18/18, 1090 Vienna, Austria
T.: +7(495) 297-50-20,
E-mail: info@brayer.su
Made in China