iCT XBA Bill Acceptor User Guide

June 5, 2024
ICT

iCT XBA Bill Acceptor - Icone

iCT XBA Bill Acceptor
User GuideiCT XBA Bill Acceptor International Currency Technologies

**Before Starting

**

Dear Valued Customer, thank you for purchasing the XBA Bill Acceptor. The XBA comes equipped with innovative wide-angle banknote insertion technology to offer a superior acceptance rate of 98% or higher. With outstanding design, the XBA has the ability to provide a very high degree of resistance to strong ambient light as well as an advanced optical and mechanical anti-fishing structure for better investment protection. The built-in USB port allows for convenient firmware upgrades via a USB flash drive.
Before installation, please check that the package contents of the XBA bill acceptor areas are listed below:

  • XBA Bill Acceptor
  • Power and Data Communication cable
  • Bill insertion bezel sticker
  • DIP switch setting guide
  • Quick Start Guide
  • C25760-R XBA Metal Plate(Option)

Should you have further questions,
XBA Bill Acceptor Installation & Service Manual can be downloaded at:
www.ictgroup.com.tw

Start Installation

Step 1: Confirm the bezel type
There are three types of bezels based on the vending machine requirements. Be sure to choose the bezel you need before ordering/ installation as each bill acceptor comes with only ONE bezel.iCT XBA Bill Acceptor -
Fig Step 2: Select InterfaceiCT XBA Bill Acceptor -
Fig1 Step 3: Prepare the connection cable
We provide the cables for MDB, RS232(ICT Protocol), Pulse, ccNet, RS232 AO, JPSTD, GPT Parallel, and talk interfaces. Each bill acceptor comes with ONE cable only. Please select the one you need to connect to.iCT XBA Bill
Acceptor - Fig2iCT XBA Bill Acceptor - Fig3iCT XBA
Bill Acceptor - Fig4iCT XBA Bill Acceptor -
Fig5iCT XBA Bill Acceptor - Fig6
Note:
XBA talk supports 12124V DC from CPU board number ‘399M30’ (399M20 or before. support 12V DC only).iCT XBA Bill Acceptor -
Fig7

Step 4: Configure the power-saving function
If your control board provides an asleep and wake-up feature (for example a battery-powered vending machine), then it can function with our power-saving mode to minimize power consumption while the machine is idle. This function allows your battery-powered machine to operate longer between chargings.
Note:

  1. The wake-up function is triggered through PIN3 of the WEL-RS7P02 cable.
  2. Please do NOT select this mode if your VMC does not support the sleep/wake-up feature. It may cause abnormal operation that affects the transaction.

Mode

|

SW3

|

SW4

---|---|---
No power-saving mode| OFF| OFF

Mode 1

|

SW3

|

SW4

XBA wakes up by bill insertion and then wakes up VMC| OFF| ON
Mode 2| SW3| SW4
XBA wakes up by VMC| ON| OFF
Mode 1+2| SW3| SW4
XBA wakes up by bill insertion or VMC| ON| ON

Step 5: Power off the Vending MachiniCT XBA Bill Acceptor - Vending
Machin Step 6: Open the door and install the XBA on the vending machine
< Standard Bezel or Standard Metal Bezel> iCT XBA Bill Acceptor - Matel
BazelNote:
Please hook up the MOLEX 5557-6IR connector of WEL-RS7P02 with the ICT coin changer cable if you choose to connect the XBA through it.

< TOB-Bezel>
Step 6-1. Install the mounting frame on the vending machine and ensure it is secured.

Step 6-2. Hook up the cable with the XBA through the 30-pin connector. Step 6-3. Buckle the XBA to the mounting frame. Step 6-4. Connect the other end of the cable to VMC to complete the installation. Note: Please hook up the MOLEX 5557-6R connector of WEL-RS7P02 with the ICT coin changer cable if you choose to connect the XBA through it.

< Standard Metal Bezel>iCT XBA Bill Acceptor - Step
5 Note:
Please hook up the MOLEX 5557-6R connector of WEL-RS7P02 with the ICT coin changer cable if you choose to connect the XBA through it
Step 7: Power on the vending machine.iCT XBA Bill AcciCT XBA Bill
Acceptor - Step 7eptor - Step 7 Step 8: Check the bezel LED
Green(Power Save Mode)/Multi-Color means the bill acceptor is functioning normally; if not please check the rear LED and refer to the chart below.
Step 9: Transaction testing
Insert bills of each accepted denomination, and check if they are accepted, and stored in the cashbox. If any problem occurs, please refer to the troubleshooting section in the service manual or contact the local ICT distributor.

Note: Please refer to the provided DIP switch setting guide to configure more options if necessary.

Step 9-1:
Check Bezel LED Error

LED Flashes Status Corrective Actions
Red Green
1 White Card Calibration Please calibrate with ICT white calibration

card.
1| | Bill jammed.| Remove the bill box by sliding the top button and the bill
path(as FIG.22), and then remove the jammed bill.
2| | Disable.| Inspect the right DIP switch setting.
3| | Recognition sensor module error.| Inspect the foreign objects on the sensor or bill path and clean.
3| 1| IR error.| Inspect the foreign objects on the sensor or bill path and clean.
3+2| | Hook sensor error.| Inspect the foreign objects on the security hook and clean.
4| | Anti-string sensor error or a stringing attempt has been detected.| Inspect the foreign objects on the sensor or bill path and clean.
5| | Bill box has been removed.| Replace the bill box.
6| | Stacker error or stacker full.| Empty the bill box.
7| | Motor error.| Inspect the foreign objects on bil path and clean.

Step 9-2:
Check Back LED ErroriCT XBA Bill Acceptor - Step
9

LED Flashes Status Corrective Actions

RED
1| White Card Calibration| Please calibrate with ICT white calibration card.
1| Bill jammed.| Remove the bill box by sliding the top button and the bill path (as FIG.22), and then remove the jammed bill.
2| Disable.| Inspect the right DIP switch setting.
3| Recognition sensor module error.| Inspect the foreign objects on the sensor or bill path and clean.
3+1| IR error.| Inspect the foreign objects on the sensor or bill path and clean.
3+2| Hook sensor error.| Inspect the foreign objects on the security hook and clean.
4| Anti-string sensor error or a stringing attempt has been detected.| Inspect the foreign objects on the sensor or bill path and clean.
5| Bill box has been removed.| Replace the bill box.
6| Stacker error or stacker full.| Empty the bill box.
7| Motor error.| Inspect the foreign objects on the bill path and clean.

If the error can not be solved after corrective actions or it recurs, please contact ICT for technical support.

© 2013 International Currency Technologies Corporation
V. 8.0 Part Number H6486G-R

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals