electro-harmonix Chillswitch Momentary Line Selection User Manual
- June 6, 2024
- electro-harmonix
Table of Contents
Electro-Harmonix Chillswitch Momentary Line Selection User Manual
Congratulations on your purchase of the Electro-Harmonix CHILLSWITCH.
KILL SETUP
In this setup, the CHILLSWITCH allows you to quickly switch between mute and unmute by pressing the footswitch, resulting in a hard rhythmic tremolo effect.
INPUT JACK – Connect to the output of your instrument or another effects pedal
SEND JACK – Disconnect
RETURN JACK – Disconnect
AMP JACK – Connect to the input of your amplifier or another effects pedal
LINE SELECTOR SETUP
INPUT JACK – Connect to the output of your instrument or another effects pedal
SEND JACK – Connect to the input of your effects loop
RETURN JACK – Connect to the output of your effects loop
AMP JACK – Connect to the input of your amplifier or another effects pedal
LED INDICATOR
In either setup, the LED reflects the signal present at the AMP jack.
LED OFF – The AMP jack outputs the original INPUT signal
LED ON – The AMP jack outputs the signal from the effects loop (or no signal, in Kill Setup)
“ENGAGE” ROTARY SWITCH
The ENGAGE rotary switch affects how the footswitch controls the AMP output.
“SEND” ROTARY SWITCH
The SEND rotary switch allows you to choose between routing the INPUT signal to the SEND jack at all times (ON position) or only when the FX Loop is active (FSW position). The setting of the SEND switch is ignored when using the KILL setup.
POWER
Power from the internal 9-volt battery is activated by plugging into the INPUT jack. The input cable should be removed when the unit is not in use to avoid running down the battery.
The barrel connector on the front of the CHILLSWITCH is for a 9-volt battery eliminator capable of delivering at least 25 mA of current. The optional 9V power supply from Electro-Harmonix is 9.6DC-200BI (same as used by Boss™ & Ibanez™) 9.6 Volts DC 200mA. The power supply must have a barrel connector with center negative. The unit’s battery may be left in or taken out when the eliminator is in use. The actual current draw of the CHILLSWITCH is 12.5 mA.
To change the 9-volt battery, remove the 4 screws on the bottom of the CHILLSWITCH. Once the screws are removed, take off the bottom plate and change the battery. Please do not touch the circuit board or you risk damaging a component.
Input Jack Impedance
INPUT – 2.2 MΩ
RETURN – 2.2 MΩ
Output Jack Impedance
AMP – 220 Ω
SEND – 220 Ω
FCC COMPLIANCE
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. If the device is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications and void the user’s authority to guarantee the equipment
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment under FCC rules.
Documents / Resources
|
electro-harmonix Chillswitch Momentary Line
Selection
[pdf] User Manual
Chillswitch, Momentary Line Selection
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>