FUSION 010-02437-01 Signature Series Wake Tower Speakers Instruction Manual

June 4, 2024
FUSION

SIGNATURE SERIES WAKE TOWER SPEAKERS
INSTALLATION INSTRUCTIONS

FUSION 010-02437-01 Signature Series Wake Tower
Speakers

Important Safety Information

WARNING
See an Important Safety and Product Information guide in the product box for product warnings and other important information.
This device must be installed according to these instructions.
Disconnect the vessel’s power supply before beginning to install this device.
CAUTION
Continuous exposure to sound pressure levels over 100 dBA may cause permanent hearing loss. The volume is typically too loud if you cannot hear people speaking around you. Limit the amount of time you listen at a high volume. If you experience ringing in your ears or muffled speech, stop listening and have your hearing checked.
To avoid possible personal injury, always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite side of the surface to avoid damaging the vessel. It is strongly recommended that you have your audio system installed by a professional installer to ensure optimum performance.
You must read all installation instructions before beginning the installation. If you experience difficulty during the installation, go to support.garmin.com for product support.
After installing an audio system, you should run the connected speakers and subwoofers at low to medium volumes for the first few hours of use. This helps to improve the overall sound by gradually loosening up the moving components of new speakers and subwoofers, such as the cone, spider, and surround.

Materials and Tools Needed

  • Electric drill

  • 12 mm ( 1 /2 in.) drill bit

  • Wire strippers

  • 16 AWG (1.3 through 1.5 mm) or larger marine-grade, fully-tinned copper speaker wire
    You can purchase this wire from your Fusion 2 ® or Garmin ®dealer:
    ◦ 010-12899-00: 7.62 m (25 ft.)
    ◦ 010-12899-10: 15.24 m (50 ft.)
    ◦ 010-12899-20: 100m (328 ft.)
    ) marine-grade, fully-tinned copper wire for the LED connections.

  • 3 A in-line fuse for the LED connections.

  • Speaker mounting bracket (sold separately)

  • 20 AWG (0.5 through 0.75 mm)1

  • Solder and water-tight heat shrink tubing or water-tight, heat-shrink, butt-splice connectors (optional)

  • Marine sealant (optional)

NOTE: For customized installations, additional tools and materials may be needed.

Mounting the Speakers

You must purchase mounting brackets for the Signature Series Wake Tower speakers separately. Each type of mounting bracket contains specific installation instructions.

  1. If necessary, mark the locations on the wake tower or the deck where you plan to mount the speakers.
  2. If necessary, drill a 12 mm ( /2 in.) cable pass-through hole in the wake tower or deck.
  3. Route the speaker and LED power wires (not included) to the mounting locations.
  4. Using the installation instructions provided with the mounting bracket, connect the bracket to the speakers and to the wake tower or the deck.
  5. Connect the speaker wires ( Speaker Wiring, page 2 ).
  6. If necessary, connect the LED power wires ( LED Wiring, page 3 ).

Speaker Wiring

When connecting the speakers to your stereo or amplifier, observe these considerations.

  • Speaker wire is not included. You should use 16 AWG (1.3 through 1.5 mm2 ) or larger speaker wire to connect the speakers to the stereo or amplifier.
  • You should use a water-tight connection method when connecting the speaker wires. You can use crimp connectors instead of solder and heat-shrink if the crimp connectors can be routed through the bracket and the wake tower or your mounting location, so you should plan and select the best connection type for your installation needs.

You can use this table to identify the polarity of the leads on the speaker.

Lead color Polarity
White Positive (+)
White with a black stripe Negative (-)

1 Various bracket are available for mounting these speakers on a wake tower bar or on a deck. See your Fusion dealer for more information.

LED Wiring

NOTICE
Using certain LED colors on the speakers, such as red and green, may violate the laws, regulations, and standards related to the use and/or operation of marine navigation lights. It is the user’s responsibility to comply with any such applicable laws, regulations, and standards. Garmin is not responsible for any fines, penalties, citations, or damages that may be incurred due to any such lack of compliance.
It is recommended to install a Fusion CRGBW Wireless Remote Control module with these speakers to turn the LEDs on and off, change the colors, and create lighting effects. See your Fusion dealer or garmin.com for more information.
You should follow the instructions provided with the CRGBW Wireless Remote Control to connect the LED wires from the speakers to the remote control receiver module and to connect the receiver to power.
If you choose not to install the remote control, you can set the static color of the LEDs by connecting combinations of the LED wires directly to the power source ( Connecting the LED Wires Directly, page 4 ).
Connecting the LED Wires Directly
If you do not install the recommended remote control, you can set the static color of the LEDs by connecting the color LED wires to the negative (-) terminal of a 12 Vdc power source. You can splice the negative (-) wire to multiple LED wires to customize the LED color and tone. You must connect the black LED wire to the positive (+) terminal of the same power source to complete the circuit.
You should use a water-tight connection method when connecting the LED wires. You can use crimp connectors instead of solder and heat-shrink if the crimp connectors can be routed through the bracket and the wake tower or your mounting location, so you should plan and select the best connection type for your installation needs. )
You should use 20 AWG (0.5 through 0.75 mm or thicker wire to connect the LED wires to the battery.
You should use a water-tight connection method when connecting the wire to the LED wiring harness.
You must connect the positive (+) wire (black) for all of the speaker LEDs to a 3 A fuse near the power source.
You should also connect the positive (+) power wire to the power source through an isolator switch or circuit breaker to turn the LEDs on and off. You can use the same isolator or circuit breaker to control the power supply to your stereo, which allows you to turn the LEDs and the stereo on and off at the same time.

  1. Connect the black wire on the LED cable to the positive (+) terminal of the power source.
    NOTICE
    To avoid damage to the speakers or the vessel, you must connect this wire through a 3 A fuse near the power source.

  2. Connect the negative (-) wire from the same power source to one or more color wires on the LED cable according to the preferred LED color.
    NOTICE
    You must insulate any unused LED wires to avoid causing a short circuit.

LED Color LED Wire Color
Red Red
Green Green
Blue Blue
Yellow Red and green
Magenta Red and blue
Cyan Blue and green
Cool white Turquoise
Warm white Yellow

NOTE: You can connect the cool white or warm white wire to change the tone of any LED color combination.

  1. Repeat for other speakers, as needed.

Speaker Information

True-Marine™ Products
True-Marine products are subjected to rigorous environmental testing under harsh marine conditions to surpass industry guidelines for marine products.
Any product that bears the True-Marine stamp of assurance has been designed for simplicity of use and combines advanced marine technologies to deliver an industry-leading entertainment experience. All TrueMarine products are supported by the Fusion 3-year worldwide limited consumer warranty.
Cleaning the Speakers
NOTE: When mounted correctly, these speakers are rated IP65 for dust and water ingress protection under normal conditions. They are not designed to withstand high-pressure water spray, which may occur when you wash down your vessel. Failure to carefully spray-clean the vessel may damage the product and void the warranty.
NOTICE
Do not use harsh or solvent-based cleaners on the speakers. Using such cleaners may damage the product and void the warranty.

  1. Clean all salt water and salt residue from the speaker with a damp cloth soaked in fresh water.
  2. Use a mild detergent to remove a heavy buildup of salt or stains.

Troubleshooting

Before you contact your Fusion dealer or service center, you should perform a few simple troubleshooting steps to help diagnose the problem.
If the Fusion speaker has been installed by a professional installation company, you should contact the company so the technicians can assess the problem and advise you about possible solutions.
There is no sound coming from the speakers

  • Verify that all connections from the source device and/or the amplifier are connected correctly to the speaker terminals.

The system lacks bass or high frequencies

  • Verify that the correct wire polarity is observed between the source and speakers. The wires should be connected positively to positive and negatively to negative.
  • Verify that the speakers are attached firmly to the mounting surface.

The audio is distorted

  • Verify that the source volume is not too loud for the speaker, and reduce the volume if necessary.
  • Verify that the panels surrounding the speaker on the vessel are not rattling.
  • Verify that the source device and/or the amplifier are connected to the speaker terminals correctly.
  • If the speaker is connected to an amplifier, verify that the input level of the amplifier is matched to the output level of the stereo. For more information, see the manual for the amplifier.

The LED lights will not turn on

  • Verify that all wiring connections are correct and tight.

Specifications

Max. power (Watts) 230 W
RMS power (Watts) 75 W
Sensitivity (1 W/1 m) 90 dB
Frequency response 70 Hz to 22 kHz
Recommended amplifier power (RMS, playing music) From 30 to 90 W
Nominal voice coil diameter 30 mm
Compass-safe distance 310 cm (122 in.)
Impedance 4 ohms
LED Supply Voltage From 10.8 to 16 Vdc
LED Load Current at 14.4 Vdc (max.) 300 mA
Operating temperature range From 0 to 50°C (from 32 to 122°F)
Storage temperature range From -20 to 70°C (from -4 to 158°F)
Cone material CURV® cone with rubber surround
Tweeter type Silk dome
Ingress protection rating IEC 60529 IP651

1 Protected against dust and water ingress.

Dimensions

FUSION 010-02437-01 Signature Series Wake Tower Speakers -
Dimensions

© 2022 Garmin Ltd. or its usion®, the Fusion logo, and True-Marine™ are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These
trademarks may not be used without the express permission of Garmin.
Amphenol™ and Amphenol AT Series™ are trademarks of Amphenol Sine Systems. CURV® is a registered trademark of Propex Furnishing Solutions.
support.garmin.com
GUID-88B8D918-34DC-41C5-9FE7-68337F4DF7E4 v1 ****

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals