BLAUPUNKT AWB3P16AT2RCM Electric Vehicle Charging Box User Manual
- June 5, 2024
- Blaupunkt
Table of Contents
BLAUPUNKT AWB3P16AT2RCM Electric Vehicle Charging Box
Preface
This product is designed and manufactured according to IEC61851 and SAEJl 772 international standards.
Use limitations of the Electric Vehicle Charging box
This EV charging box is designed for use in the following conditions:
Sea level < 2000m
Surrounding Temperature -40 C – 45 C
Relative humidity of< 85%.
More severe conditions require special instructions when ordering.
Precautions and dangers
Note: please follow the safe use instructions and legal notes.
The EV Charging Box must always be installed according to the legal
requirements in the country of installation.
Danger: voltage hazard
This product can cause serious injury if you come into contact with its
internal parts during work. Furthermore, please disconnect the power supply
after use.
Repair:
Do not try to repair the product. In case of problems please contact the
customer service.
Warning: opening the device without permission may cause danger
Opening the device without permission may cause harm to the user or cause
significant damage to itself or the surroundings.
Note: unauthorized modification of the device will result in the loss of
manufacturer’s warranty
No unauthorized modification of the device is allowed, any attempt to do so
and the manufacturer’s warranty will be revoked.
Safety Precautions
- Do not put inflammable, explosives, combustible materials, chemicals, combustible steam and other dangerous articles near the charging box.
- Keep the charging connector head clean and dry. In case of dirt, wipe it with a clean dry cloth. It is strictly prohibited to touch the core of the charging connector core with your hand while it is charging.
- It is strictly prohibited to use the EV Charging Box if there is visible damage, cracks, abrasions or exposed metal in the connector or charging cable. In case of such, please contact the After Sales Service.
- Do not attempt to dismantle, repair or modify the EV Charging Box. If in need for repair or modification, please contact the After Sales Service. Improper operation may cause damage, water leakage, power leakage or other situations which can lead to personal injury or product failure.
- Show caution when using during rain or thunder.
- Children are not allowed to approach or use the EV Charging Box during the charging process in order to avoid injury.
- Do not attempt to charge the vehicle when moving. The vehicle must be at a complete stand still during the entire charging process.
Product Introduction
This product is a single-phase or three-phase EV Charging Box, solely used for
ac charging of electric vehicles. The equipment adopts industrial design
principles. The protection level of the EV Charging Box reaches IPSS, with
good dustproof and waterproof functions, and can be operated and maintained
safely outdoors. This series Electric Vehicle Charging Box come in two
version: the cable version and the socket version.
Mechanical And Electrical Installation
Internal Structure Drawing
Installation
-
Overall dimension and installation size (unit: mm)
-
The power line is connected with terminal.the single- phase EV Charging Box is connected with N and L, and the three-phase EV Charging Box is connected to N ,L 1, L2 and L3. Ground wire (PE wire) is connected to the yellow and green terminals.
The connecting point of the EV supply equipment shall be protected by an RCD having a rated residual operating current not exceeding 30 mA; -
Recommended cable section:
-
Current option and setting by DIP switch
WARNING :installation and AMP settings are only to the carried out by a trained and authorized electrical installer.
For the socket version (AWBl P32AT2SRCM/AWB3P32AT2SRCM), the current is set to 32A as default factory setting. However , the rating can be adjusted to 10, 16,20,25,32 via built-in DIP switch of protocol controller as user request.
For the cable version (AWBl Pl 6AT2RCM/AWB3Pl 6AT2RCM), the current is set to 16A as default factory setting. However ,the rating can be adjusted to 8, 10, 13, 16 via built-in DIP switch of protocol controller as user request. DIP switch settings for the cable and socket version :
Charging Process
Check before operation
Before operation, please carefully check and ensure the following items:
The installation position of the EV Charging Box should be convenient for
operation and maintenance. The EV Charging Box shall be properly installed
using the mounting bracket included in the accessories.
No external objects or parts are left on top of the EV Charging Box.
Power on the equipment
- A. Confirm that all the above pre- operation inspection items meet the requirements.
- B. Switch on the power supply inlet circuit breaker.
- C. After the EV Charging Box is connected to the power supply, allow for 7 seconds of startup self-test time, and the indicator light will be displayed switching between red, blue and green.
- D. After the self-test is completed, the indicators blue light flashes for cable version, the indicators blue steady light for free/socket version and the EV Charging Box is ready for use and you can connect to you Electric Vehicle.
- E. After connecting your EV Charging box to you Electric Vehicle, please refer to the table below for the status of the charging process.
Warranty
The warranty period of this product is 24 months after the date of purchase.
During the warranty period, if handled properly and according to the manual,
if the product becomes defect please contact our After Sales Service for
assistance.
During the warranty period, a certain maintenance fee will be charged for
damage caused by the following reasons:
- A. Damage caused by wrong use of the product and unauthorized repair and modification.
- B. Damage caused by abnormal fire, flood or other natural disasters and secondary disasters.
- C. Damage caused by dropping the unit or damage caused by transportation after the purchase.
- D. Damage caused by failure to operate according to the user manual provided by our company.
BLAUPUNKT reserves the right to interpret this agreement.
BLP EV Systems I ApS Ediths Alie 8 I DK-S2S0 Odense SV I info@blaupunkt-
ev.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>