Carrier RMAP-ST Air Purifier XK for Rooms User Manual

: June 5, 2024
: Carrier

Carrier RMAP-ST Air Purifier XK for Rooms

vCarrier RMAP-ST-Air-Purifier-
XK-for-Rooms-PRODUCT

Indication Description

Indicates that there is a possibility of death or serious injury in case of violation of the instructions.
Indicates that there is a possibility of injury or material damage in case of violation of the instructions.

Power Supply

This product has a polarized plug (one blade is wider than the other).
To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit in the outlet, contact a qualified electrician.
Do not attempt to defeat this safety feature.
Be sure to plug your product into a 120V outlet.
Do not turn off the product by unplugging the power plug while in use.
Contact customer service if the power plug or the power cord is damaged.
Connect the power plug firmly to the wall outlet and do not use a damaged power plug, a damaged power cord, or loose outlet.
Unplug the product during thunder and lightning. Product can be damaged due to electric shock.
If the product is not used for long period of time, unplug the unit to prevent unnecessary overheating and to save electricity consumption.

Initial Setup

WARNING

Plug the product into an outlet. Do not press the product up against the wall plug.
Do not extend the power cord at will.
Do not use with a power strip as it may cause electric shock or fire.
Leave at least 12 inches (30 cm) between wall and product.
If the air inlet and outlet space is crowded, it may impact the product’s ability to filter and recirculate the air.

Place on flat surface.

Do not use the product near flammable substances or a gas leak.
Do not use the product in places exposed to high humidity, oil, grease, or water.
Do not install the product in direct sunlight or near a heating vent.

When Using

CAUTION

Avoid installing the product within 3 feet (1 meter) of a television or other electronic device.
Turn off the power immediately if water or other foreign matter enters the product.
Dry the product completely before turning on. Using a dirty pre-filter or no filter will degrade product performance.
If there is a strange sound, burning smell or smoke coming from the product, unplug it immediately and contact customer service.
Do not replace the filter while the product is in use or plugged in.
Do not use filters that are not recommended by the manufacturer.
Do not move the product while in use.

When Cleaning

Do not clean when power is on as it may cause electric shock or malfunction.
Remove the plastic packaging from the filter before use.
Keep plastic packaging away from children as it may cause suffocation.

How to Prepare/Change the Filter

An integrated filter is included with the new product.
Remove the filter packaging before plugging in the product.

Note: You cannot return the filter once the plastic packaging is removed.

Preparation Before Use

Hold the top cover of the product with both hands and pull up.
Grasp the filter cover hole on the rear and pull it forward.
Remove the filter from the product and then remove the plastic packaging from the filter.
Failing to remove the packaging will result in abnormal sounds and the filter will not work properly; and it may cause a fire or other damage to the product.
Slide the filter back into the unit.
Replace filter cover.
Insert the cover into the fixed groove at the bottom of the product.
Slide the cover forward so that the cover fits into the top grooves.
Hold the top cover of the product with both hands and slide it back in place, making sure the logo appears in the front.
When the filter installation is complete, press the +” ” button on the control panel for five seconds or more to reset the filter indicator light.
The red filter light will turn off when the product is reset.

How to Install Casters (Optional)

Inside of the air purifier package, there is a small box containing four casters and eight screws.
Remove the four bottom bases from the air purifier with a screwdriver.
Replace each base with a caster, utilizing two screws per caster.
Retain the removed bottom bases and screws for future use.

Note: If there is no caster box inside the filter box, please contact customer service at 1-888-320-0909.

Product Description

Carrier RMAP-ST-Air-Purifier-XK-for-Rooms-
FIG-7

Note: Product features and specifications may vary depending on the model.

Product Specifications

Carrier RMAP-ST-Air-Purifier-XK-for-Rooms-
FIG-8

Model| Air Purifier RMAP-ST| Air Purifier XL RMAP-XL| Smart Air Purifier RMAP-SST| Smart Air Purifier XL RMAP-SXL
---|---|---|---|---
Power| 120V, 60Hz, 1-phase
Wi-Fi®| No| No| Yes| Yes
Remote Control| No| No| Yes| Yes

Dimensions

| 13.7″ W x 13.7″ D x 26.5″ H

350mm W x 350mm D x 675mm H

| 13.7″ W x 13.7″ D x 31.5″ H

350mm W x 350mm D x 800mm H

| 13.7″ W x 13.7″ D x 26.5″ H

350mm W x 350mm D x 675mm H

| 13.7″ W x 13.7″ D x 31.5″ H

350mm W x 350mm D x 800mm H

RMAPFIL-HST

| ****

RMAPFIL-HXL

| ****

RMAPFIL-HST

| ****

RMAPFIL-HXL

Filter Detail

Filter Type	Function
① Pre-Filter (microfiber net)	****

Removes large dust particles and pollutants.

② HEPA Filter

| ****

Removes 99.97% of particles that are 0.3 microns in size.

③ Carbon Filter

| Removes odors, gases and VOCs not removed from the HEPA filter .

It is recomended that you replace the filter every 6-12 months. Replacement period may vary depending on the product usage. Visit CarrierAtHome.com to Note order your replacement filter.

**Display

Carrier RMAP-ST-Air-Purifier-XK-for-Rooms-
FIG-10 Control Panel Carrier RMAP-ST-Air-
Purifier-XK-for-Rooms-FIG-11 Control Panel Descriptions**

Sleep| Sleep mode / Timer| **| Use the up arrow to set fan speed as well as time for Auto-off mode**
---|---|---|---
LED

Note: See page 12 for a complete list of product operations.

Remote Control

Remote Control Buttons

Sleep| Sleep mode / Timer| **| Use the up arrow to set fan speed as well as time for Auto-off mode**
---|---|---|---
LED

Remote Control Battery

CAUTION

This product contains a lithium button/coin cell battery.
If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as two hours.
Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the battery, and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Product Operation

Connecting Wi-Fi Models to App

Download the free Carrier® Home App to your device. Enable Bluetooth® on your mobile device.
Make sure the room air purifier is plugged into an outlet and is powered on. Bluetooth will automatically turn on.
Launch the app and sign up for a new account if you do not already have one.
On the app, tap “Add device” and select the device you want to add to your account.
Scan the QR code on the side of the air purifier. You will see a six-digit pairing code on the app and the unit.
Confirm the pairing PIN by pres Lansing on the unit.
Select your Wi-Fi® Network and enter your password.
Your room air purifier is now connected to Wi-Fi. See the list of remote access features below.

Remote Access Features from App

In-app account creation and Wi-Fi provisioning
View all devices in a dashboard
View indoor PM2.5 concentration levels
View indoor TVOC levels
Control air purifier speed
Set unit to AUTO mode
View the remaining filter life
Place order for new filter
View outdoor air quality levels
Alexa and Google Home integration

Normal Operation

When the air purifier turns on, the sensor is initialized and the display shows during initialization.
Press the button to turn on.
The previously selected operation mode will be displayed.
Press the button on the control panel (or button on Remote Control) to select your desired fan speed.
You can adjust the fan speed from level 1 (F1) to level 18 (F18).
The default home display on Wi-Fi models will show a PM2.5 reading. Once the button is pushed, the display will switch to show designated fan speed.

Auto Operation

Auto Mode allows the system to determine the fan speed depending on the air quality of the room. Press the button to turn on.
The previously selected operation mode will be displayed. Press the ” ” button (or button on the Remote Control)to select Auto mode.
Each time the button is pressed, it switches between Auto Operation and Normal Operation.
The fan speed cannot be adjusted during Auto Operation.
In Auto mode, the Indoor Air Quality Monitor detects the indoor air quality and the device automatically adjusts the fan speed to filter the air accordingly.

Turbo Fan Operation

Turbo mode allows the room’s air to be filtered faster. Press the button to turn the product on. 1
Set Turbo Fan Operation by pressing the buttons on the control panel simultaneously for three seconds.
If you press the button on the control panel (or on the Remote Control), the fan speed will change to level 18, and Turbo Fan Operation will stop.
You can now set your fan speed to any preferred level.

Sleep Operation

Sleep mode allows the system to run normally but the display panel will be dark. Press the button to turn on.
During sleep mode, the entire display panel is turned off, except for .
The fan speed is set to level 1 by default. Press the arrows to select preferred fan speed.
If you press the sleep button again during sleep mode, it will operate in the previously selected mode.
Sleep mode will be cancelled if the unit is turned off.
Press the button on the control panel (or button on the Remote Control) to select the Sleep mode.

Safety Lock Function

You can set the safety lock function so that children can not operate the product.
If you press the + button (or the button on the Remote Control) for more than three seconds while the product is on, the display shows and the Safety Lock function is set.
If you press a button on the control panel while this function is on, will flash on the display five times at one-second intervals.
To cancel this function, press the + button simultaneously for more than three seconds. Or press the button on the Remote Control to cancel this function.

Mute Function

Mute: Press and hold the button and the AUTO button simultaneously for three seconds toturn on and off the beep sound.

Auto-Off Function

While the product is on, press the button (or the button on the Remote Control) for more than three seconds.
Initially, 1h is displayed. Press the button on the control panel (or the button on the Remote Control) to select the desired run time.
You can select from 1 hour to 12 hours. (If you do not press the button for five seconds, it returns to the previous display.)
After selecting the desired run time, press the button on the control panel for three seconds or longer (or the button on the Remote Control).
You will hear the beep sound and the timer symbol will be shown on the display.
When in Auto-Off mode the room air purifier will automatically turn off after the set run time.
If the power is disconnected the scheduled auto-off time will be canceled, and a new auto-off time will need to be set.

Indoor Air Quality Indicator

Indoor Air Quality (IAQ) Indicator

You can check the indoor air quality in real-time by using the indoor air quality indicator. This indicator appears as a light around the outer edge of the display monitor.
The indoor air quality is displayed based on the density of fine particles and VOC density being sensed by the unit.

Color Code

| Color| Air Quality| PM2.5 Reading (µg/m 3 )| VOC Density
---|---|---|---|---
Level 1| Green| Good| 0-12| Low
Level 2| Yellow| Moderate| 13-35| Medium
Level 3| Orange| Bad| 36-55| High
Level 4| Red| Very bad| Equal or above 56| Very high

IAQ indicator may not react to some particles and its readings may be different from that of other air quality measuring products and instruments.

Care and Maintenance

How to Clean the Product

Unplug the product before cleaning.
Clean the air purifier once or twice a month for optimal function.
In areas with high levels of dust, it is recommended to clean the air purifier more frequently.
Using a damp cloth, clean the exterior of the room air purifier and wipe dry with a soft cloth.
Open the filter cover on the back and remove the filter. Clean the inside of the filter cabinet with a vacuum cleaner and damp towel.
Clean the product and the pre-filter once or twice a month.

Cleaning the Filter

If the filter is extremely dirty, replace it.
Filter contamination may vary depending on your environment and the number of hours you have run the air purifier.
The timing of filter cleaning may vary accordingly.
In between filter replacements, clean the pre-filter with a vacuum cleaner or a soft brush.
Never wash the filter with water.

Replacing the Filter

The filter replacement indicator light will turn red when it is time to replace the filter.
Replace the filter every 6-12 months.(See pages 5-6 for details on installing filter and see page 8 for filter by model information.)
After replacing the filter, reset the indicator light. Press the ” button on the control panel for five seconds or longer to reset the indicator light.

Note: The life of the filter depends on your environment and use.

Cleaning the Dust Sensor

Hold the top cover of the product with both hands and pull up.
Grasp the filter cover hole on the rear and pull it forward.
Remove the cover of the dust sensor located on the right side of the product.
Wipe the lens and inlet of the dust sensor with a damp cotton swab. Thoroughly dry with a clean, dry cotton swab.
Replace the cover of the dust sensor. Replace the filter cover. Replace the top cover of the product with the logo facing the front.

CAUTION
Do not wipe sensor parts with harsh cleaning chemicals, such as acetone, alcohol, etc. It may cause damage to the lens.

Long Term Storage

Run the product for one hour and then disconnect from the power outlet.
Cover the product and store in a dry space out of direct sunlight.

Troubleshooting

Symptom	Check	Solution

The product does not turn on when pressing the Power button.

| Is there a power outage?| Confirm power is on in the home, then try Power button again.

Is the power plug connected?

| Make sure the power plug is fully pushed into the outlet, and then try power button again.
Is the power outlet working?| Attempt to plug product into a different power outlet and turn on.
Filter replacement indicator is still on.| Did you press the Sleep + “ Auto “ button at the same time for more than five seconds after replacing the filter?| When replacing the filter, be sure to press the Sleep + “ Auto ” button for at least five seconds until the ‘ding’ sound is heard.
Product is producing a strange smell.| Check if the dust filter or deodorizing filter smells strange.|

Replace the filter.

“FAN” flashes on the screen.| Unplug the unit, wait 10 seconds, and then plug the unit back in. Is the “FAN” indicator still flashing?| Unplug the power cord and contact customer service.
When trying to pair my unit to the app, why am I being asked to re-scan the QR code?| ****

Is your phone close enough to the unit so that Bluetooth stays connected?

| ****

During the pairing process, stay close to the unit with your phone and be ready to enter the codes when prompted.

The app is saying I entered incorrect Wi-Fi® credentials|

Make sure you have your correct Wi-Fi credentials on hand.

| ****

Follow the prompts to scan the QR code and start the pairing process again.

Customer Support

For customer assistance please call 1-888-320-0909, or go to CarrierAtHome.com for a complete list of Frequently Asked Questions.
For filter replacement, go to CarrierAtHome.com for details.

Warranty

FOR WARRANTY SERVICE OR REPLACEMENT:
Contact Carrier at 1-888-320-0909.
Retain this document for your records.
Model Number
Serial Number
Date ____
The Carrier Air Purifier and Smart Air Purifier models carry a one-year warranty from the date of purchase. See warranty card for additional details.

FCC Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 8 inches (20cm) between yourself and the radiator. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.