VonHaus 3500021 900W Angle Grinder Instruction Manual

VonHaus 3500021 900W Angle Grinder

WARNING

PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Please retain all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

INTENDED USE.
Only use the Angle Grinder as described in this manual. The use of any accessory or attachment or performance of any operation with this tool other than those recommended in this instruction manual may present a risk of personal injury and/or damage to property.
This tool is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning use of the tool by a person responsible for their safety.
Children should be supervised to ensure they do not play with the tool.

ELECTRICAL SAFETY.
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering the power tool will increase the risk of electric shock.

WORK AREA SAFETY.
Keep your work area clean and well-lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids, gases or dust. Power tools create sparks that may ignite dust or fumes.
Keep bystanders, children and animals away while operating the power tool. Distractions can cause you to lose control.

BEFORE USE.

WARNING! Know your Angle Grinder. Do not plug the tool into the power source until you have read and understood the information in this manual. Learn the tool’s applications and limitations, as well as the specific potential hazards related to this tool, in order to reduce the risk of electric shock, fire or serious injury.

WARNING! If any part is missing or damaged, do not plug the tool into the power source or install any accessory until the missing or damaged part is repaired or replaced. Failure to follow this instruction could result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce the risk of personal injury.

WARNING! Contact with, or inhalation of, dusts arising from cutting applications may endanger the health of the operator and possible bystanders. Wear a dust mask specifically designed for protection against dust and fumes and ensure that persons within or entering the work area are also protected.

Always wear eye protection. Any power tool can throw foreign objects into your eyes and cause permanent eye damage. Always wear safety goggles (not glasses) that comply with ANSI safety standard Z87.1. Everyday glasses have only impact-resistant lenses. They are not safety glasses.

WARNING! Wearing glasses or goggles not in compliance with ANSI Z87.1 when operating this tool could cause serious injury.
Dress appropriately. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts to prevent them from becoming caught in the tool.
Remove any adjusting key or wrench before turning the power tool on. A wrench or key left attached to a rotating part of the power tool may result in personal injury.
If devices are provided for the connection of dust extraction and collection facilities, ensure that these are connected and properly used to reduce dust- related hazards.
Use clamps, or another practical way, to secure and support the workpiece to a stable platform. Holding the workpiece by hand or against your body leaves it unstable and may lead to loss of control.
Make sure that there are no nails or foreign objects in the path of the workpiece to be cut or sanded.
Be aware of hidden hazards. Before cutting into walls, floors or ceilings, check for the location of wiring and pipes.
Prevent unintentional starting. Ensure the switch is in the off position before connecting to the power source and/
or battery pack, picking up or carrying the tool. Carrying power tools with
your finger on the switch, or energising power tools that are switched on, invites accidents.

POWER TOOL USE AND CARE.

Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the  working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
WARNING! Only use accessories recommended for use with this Angle Grinder. Follow the instructions that accompany the accessories. The use of improper accessories may result in injury to the operator or damage the tool.
Do not use the power tool if the switch does not turn it on and off. A power tool that cannot be controlled with the switch is dangerous and must be repaired.
Stay alert, watch what you are doing and use common sense when operating a power tool.
Do not use a power tool whilst tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating a power tool may result in serious personal injury.
Hold the power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring or its own cord. A cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Keep hands away from the cutting area. Never reach underneath the workpiece for any reason. Do not insert fingers or thumb into the vicinity of the blades/sanding attachments. Do not stabilise the Angle Grinder by gripping the shoe.
Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
Do not overreach. Keep proper footing and balance at all times. This will enable better control of the power tool in unexpected situations.
Disconnect the plug from the power source and/or the battery back from
the power tool before making any adjustments, changing accessories
or storing. Such preventative safety measures reduce the risk of starting the power tool accidentally.
The blade will continue to move after releasing the switch. Always switch the tool off and wait for the blade to come to a complete standstill before putting the tool down.
Do not touch the workpiece or the blade immediately after operating the tool. They can become very hot.

STORAGE & MAINTENANCE.

Store idle power tools out of reach
of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. Maintain the power tool. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
Keep blades sharp. Dull or damaged blades may cause the Angle Grinder to swerve or stall under pressure. Always use the appropriate type of blade/sandpaper for the work-piece material and type of cut/sanded.
When cutting pipe or conduit, make sure that they are free from water, electrical wiring, etc.
Never use dull blades in the tool. They will cut slower, leave rough cuts and break easily due to added pressure and excessive heat. They will also overload the motor and cause premature failure of the tool.
Have your power tool serviced by a qualified repair person using identical replacement parts only to ensure that the safety of the power tool is maintained. Do not attempt repairs yourself.

SAFETY SYMBOLS

The following safety symbols may appear on this product. Please ensure you understand their meanings before operating the Angle Grinder in order to prevent personal injury and avoid damage to the tool.

SPECIFICATION

1. On/Off Slide Switch
2. Spindle Shaft (see page 6)
3. Side Handle
4. Gearbox
5. Safety Guard
6. Spindle Lock Button
7. Spanner
8. External Flange with Thread (see page 6)
9. Internal Flange (see page 6)
10. Safety Guard
11. Cutting Disc (125mm)
12. Grinding Stone (125mm)
13. Grinding Stone (125mm)
14. Flap Disc (125mm)
15. Flap Disc (125mm)
16. Cutting Disc (125mm)

HANDLE MOUNTING

• IMPORTANT Always mount the SIDE HANDLE (3) to the desired position before operation.
• DO NOT use the Power Tool without the SIDE HANDLE (3) installed.
• IMPORTANT Always keep one hand on the back of the tool and the other on the SIDE HANDLE (3) at all times during operation.

ATTACHING THE SAFETY GUARD

NOTE The SAFETY GUARD (5) cannot be rotated more than 45° on either side of the Power Tool.

ATTACHING THE DISC

• IMPORTANT Press down the SPINDLE LOCK BUTTON (6) firmly.
• Keeping it pressed down, tighten the EXTERNAL FLANGE (8) clockwise with the SPANNER (7) until tight.
• IMPORTANT Allow the Angle Grinder to run in idle for at least 1 minute with the required disc now securely fastened.
• NEVER Use a vibrating disc. This should immediately be replaced.

POWERING ON & OFF

• NOTE For continuous operation, push the ON/OFF SLIDE SWITCH (1) fully forwards and depress to lock it in position.
• Press the REAR of the ON/OFF SLIDE SWITCH (1) to release the locking and switch off the Angle Grinder.

DANGEROUS RESTART

This Product is fitted with a DANGEROUS RESTART device. If the power is cut to the product during use (such as disconnection from the mains) the tool will not power back on when plugged back in.
Unless the tool has been switched off first. This is to prevent a user plugging the tool in without the user checking the position of the power switch first.

MAINTENANCE

CLEANING THE TOO
Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, shortening the tool’s service life.
Clean the body of your tool with a soft brush or dry cloth.

CAUTION Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, use a mild detergent on a damp cloth.
WARNING Do not allow water to come into contact with the tool.

If available, use clean, dry, compressed air to blow through the ventilation holes (where applicable).
Ensure the tool is thoroughly dry before using it.

LUBRICATION
All of the bearings in this tool are lubricated with
a sufficient amount of high-grade lubricant for the life of the unit under normal conditions. As such, no further lubrication is required.

GENERAL INSPECTION
Regularly check that all the screws are tight as they may vibrate and loosen over time.

REPAIRS
WARNING Repairs should only be carried out by an authorised technician using identical replacement parts. Do not attempt repairs yourself.

STORAGE

Store this tool carefully in a secure, dry place, out of reach of children.

TROUBLESHOOTING

THE TOOL WILL NOT START

| ****

Ensure the tool is connected to mains power.

Activate the ON/OFF Switch.

Check the fuse and replace if required.

Dangerous restart may have been activated.

THE TOOL KEEPS KICKING/STALLING

| ****

Relieve some pressure on the tool. Do not exert extra force, let the tool do the job.

EXCESSIVE VIBRATION

| ****

The material is too thick and is placing strain on the motor.

If excessive noise continues, discontinue use and seek repairs.

EXCESSIVE NOISE

| ****

Too much force is being exerted on the tool. Use less force.

THE TOOL IS OVERHEATING

| ****

Allow the tool to cool before using again.

DISPOSAL INFORMATION

Please recycle where facilities exist. Check with your local authority for recycling advice.

WARRANTY

To register your product and find out if you qualify for a free extended warranty, go to:
www.VonHaus.com/warranty
Please retain a proof of purchase receipt or statement as proof of the purchase date.
The warranty only applies if the product is used solely in the manner indicated in the Warnings page of this manual, and all other instructions have been followed accurately. Any abuse of the product or the manner in which it is used will invalidate the warranty.

Returned goods will not be accepted unless re-packaged in its original packaging and accompanied by a relevant and completed returns form. This does not affect your statutory rights.
No rights are given under this warranty to a person acquiring the product second-hand or for commercial or communal use.

COPYRIGHT

All material in this instruction manual are copyrighted by DOMU Brands Ltd.
Any unauthorised use may violate worldwide copyright, trademark, and other laws.

DECLARATION OF CONFORMITY

We:
DOMU Brands Ltd
5th Floor The Tower
Deva City Office Park
Manchester
M3 7BF
Declare under our sole responsibility that the product: SKU: 3500021
Description: VonHaus 900W Angle Grinder

References

• Human Rights Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>