VonHaus 3515387 800W Paint Station Instruction Manual
- June 5, 2024
- vonhaus
Table of Contents
VonHaus 3515387 800W Paint Station
WARNING
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE
INTENDED USE
Only use the Paint Station as described in this instruction manual. This Paint Station it is not suitable for industrial or commercial use. The use of any accessory or attachment or performance of any operation with this product other than those recommended in this instruction manual may present a risk of personal injury and/or damage to property. This Paint Station is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning use of the product by a person responsible for their safety. Children should be supervised to ensure they do not play with the product.
GENERAL SAFETY INFORMATION.
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Please retain all warnings and instructions for future reference.
ELECTRICAL SAFETY.
Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your
body is earthed or grounded.
Do not expose the product to rain or wet conditions. Water entering the
product will increase the risk of electric shock.
WORK AREA SAFETY.
Keep your work area clean and well lit. Cluttered or dark areas invite
accidents. Do not operate in explosive atmospheres such as in the presence of
flammable liquids, gases or dust.
Keep bystanders, children and animals away while operating the product.
Distractions can cause you to lose control.
BEFORE USE.
WARNING! Know your Paint Station. Do not plug the product into the power source until you have read and understood the information in this manual. Learn the product’s applications and limitations, as well as the specific potential hazards related to this product, in order to reduce the risk of electric shock, fire or serious injury.
WARNING! If any part is missing or damaged, do not plug into the power
source or install any accessory until the missing or damaged part is repaired
or replaced. Failure to follow this instruction could result in serious
personal injury. Do not use while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating may
result in injury.
Use only paints, solvents or other materials with a flash point of 39°c or
higher. The materials used with this Paint Station (paint, thinners, etc.) may
contain hazardous, harmful, explosive or corrosive materials. Always ensure
there is adequate ventilation when spraying.
NEVER spray near an open flame, including an appliance pilot flame. NEVER smoke near the Paint Station, paint or other flammable objects. Always disconnect the unit from the electrical outlet when cleaning the Paint Station. Always ensure the spray area is safe and free from all debris that may present a fire or trip hazard.
NEVER , under any circumstances, point the Paint Station at another person or animal. In the event of an injury, seek immediate medical attention.
NEVER allow children or unauthorised users to operate or play with the spray equipment. Always read the paint manufacturer’s thinning instructions before use. Always wear a protective face mask when spraying. We also recommend wearing gloves, goggles and overalls. You must clean the Paint Station thoroughly after each use. Do not use or place paint or other flammable materials near ignition sources such as static electric sparks, open flames, pilot lights, electrical appliances, or hot objects. Connecting or disconnecting
STORAGE & MAINTENANCE.
Store the product out of reach of children and do not allow persons unfamiliar
with the product or these instructions to operate the product.
SAFETY SYMBOLS
The following safety symbols may appear on this product. Please ensure you understand their meanings before operating the Paint Station in order to prevent personal injury and avoid damage to the tool.
SPECIFICATION
- Spray Pattern Adjuster
- Nozzle
- Locking Nut
- Air Hose
- Spray Gun
- Max. Paint Volume Control
- Trigger
- Container
- Motor Unit
- On/Off Switch (see page 5)
- Shoulder Strap
- Cleaning Needle
- Cleaning Brush
- Viscosity Cup
- Suction Tube
- Air Filter
MATERIAL PREPARATION
-
IMPORTANT Before spraying, the material being used may need to be thinned with solvent; as specified by the material manufacturer.
-
WARNING Do not use materials with a flashpoint below 39°C.
-
NOTE Follow the instructions below.
Stir the spraying material thoroughly before measuring viscosity. -
Dip the VISCOSITY CUP (14) completely into the spraying material.
-
Hold the VISCOSITY CUP (14) and measure the time in seconds until the spray material empties out.
-
This time duration is referred to below as *Runout Time.
THINNING CHART
IMPORTANT Material to be sprayed should always be strained to remove any
impurities in the paint which may enter and clog the system.
Impurities in the paint may give poor performance and a poor finish.
OPERATION
- Attach the tilted end of AIR HOSE (4) into the back of the SPRAY GUN (5).
- Attach the opposite end of the AIR HOSE (4) into the slot at the base of the MOTOR UNIT (9).
- NOTE This has two lugs to align and twist clockwise to secure into position.
- Plug the Paint Station in at a suitable mains socket.
- Press the ON/OFF SWITCH (10) to the I position to switch on.
- Press the ON/OFF SWITCH (10) to the 0 position to switch off.
ALIGNING THE SUCTION TUBE
- Unscrew the CONTAINER (8) from the SPRAY GUN (5) and rotate the SUCTION TUBE (15) to the correct position.
- If you are going to be spraying in a downward direction, the angled end of the SUCTION TUBE (15) should be pointing towards the front of the Spray Gun.
- If you are going to be spraying in an upward direction, the angled end of the SUCTION TUBE (15) should be pointing towards the rear of the Spray Gun.
- NOTE By following the practices above, this should prevent you from having to refill the container as often, and reduce paint splatter.
SURFACE PREPARATION
- All objects to be sprayed should be thoroughly cleaned before spraying.
- Areas excluded from spraying should be masked off appropriately.
- NOTE When spraying outdoors, the spraying area must be free of dust in order to avoid blowing dust onto the freshly sprayed surface.
SPRAY TECHNIQUE
- ADVISORY If spraying with an HVLP spray system is new or unfamiliar to you, it is strongly advisable to practice on a piece of cardboard or wood offcuts before proceeding on your intended workpiece
- Spray parallel to the surface with smooth passes at a consistent speed as illustrated below. Adhering to this will avoid irregularities in the final finish.
- Always apply a thin coat of material on the first pass and allow to dry before applying a second, slightly heavier coat.
- Position the Spray Gun perpendicular to one or more inches from the spray surface.
- NOTE The closer the sprayer is to the object being sprayed the lower the overspray.
- ADVISORY When spraying, always trigger the spray gun after spray pass has begun and release the trigger before stopping the pass.
- NOTE Always keep the spray gun pointed squarely at the spray surface and overlap passes slightly to obtain the most consistent finish.
SPRAY PATTERN ADJUSTMENT
- The spray pattern shape is adjusted by rotating the SPRAY PATTERN ADJUSTER (1) to either the vertical, horizontal or diagonal positions.
- Loosen the LOCKING NUT (3) sufficiently to enable you to rotate the SPRAY PATTERN ADJUSTER (1).
- The positions of the SPRAY PATTERN ADJUSTER (1) and corresponding spray pattern shapes are illustrated below.
- Test each pattern and use whichever pattern is suitable for your application.
FLOW ADJUSTMENT
- Set the material flow volume by rotating the MAX. PAINT VOLUME CONTROL (6) behind the TRIGGER (7) of the spray gun.
- Rotate the MAX. PAINT VOLUME CONTROL (6) clockwise for greater volume and anti-clockwise for decreased volume.\
CLEANING & MAINTENANCE
NOTE Always flush the spray outdoors. Area must be free of flammable vapours. Cleaning area must be well ventilated.
-
Unplug the paint station and trigger the spray gun so that the material inside the spray gun flows back into the container.
-
Unscrew the container. Empty any remaining material back into the material container.
-
Pour a small amount of appropriate cleaning solution into the container.
Warm, soapy water for latex materials.
Mineral spirits for oil based materials.
Clean the container and dispose of the cleaning solution. -
Refill the container with NEW cleaning solution.
-
Attach the container to the gun and plug in the spray gun at the mains.
-
Spray solution through the gun for 2 seconds in a safe area.
NOTE The same substance that is used to thin the paint is also used for cleaning.
NOTE Improper cleaning of the spray gun and all of its components may significantly reduce the life of the product.
Spray again for 2 seconds. Unplug the paint station from the mains and trigger the gun so that the material inside the spray gun flows back into the container. -
Wipe the exterior of the container and spray gun.
-
Uncsrew the nut and remove the air cap and nozzle.
-
Clean the container, suction tube, air cap and nozzle with a cleaning brush and the appropriate cleaning solution.
NOTE Never clean the nozzle or air holes in the spray gun with sharp metal objects.
Do not use solvents containing silicone -
Clean the rear of the spray gun with appropriate cleaning solution.
Turn the suction tube anticlockwise and pull the suction tube downward to disassemble it from the spray gun.
Clean the suction tube with appropriate cleaning solution.
IMPORTANT Ensure the SPRAY PATTERN ADJUSTER (1), NOZZLE (2) and LOCKING
NUT (3) are reassembled correctly after cleaning.
Failure to adhere to this may result in some paint in the container being
sucked into the air duct and adversely affecting the operational function of
the unit.
REMOVING THE AIR FILTER
- The AIR FILTER (16) should be cleaned on a regular basis to ensure the optimal performance of the paint station is maintained.
- Squeeze both clips either ends of the air filter cover and remove the sponge inside.
- IMPORTANT Clean the sponge with warm soapy water and allow to dry for at least 24 hours before replacing the sponge back into the paint station.
TROUBLESHOOTING
PROBLEM| CAUSE
1. Nozzle clogged
2. Suction tube clogged
3. Suction tube loose
4. No pressure build up
5. Air Filter clogged
| SOLUTION
---|---|---
LITTLE OR NO PAINT FLOW
| 1. Clean
2. Clean
3. Insert
4. Tighten container
5. Change
MATERIAL LEAKING
| 1. Nozzle loose
2. Nozzle worn
3. Nozzle seal worn
4. Material build up on cap/nozzle
| 1. Tighten
2. Replace
3. Replace
4. Clean
PAINT ATOMISATION IS TOO COARSE
| 1. Viscosity is too high
2. Material volume too high
3. Nozzle clogged
4. No pressure build up
| 1. Decrease volume setting
2. Decrease volume setting
3. Clean
4. Tighten container
SPRAY JET PULSATES
| 1. Material in container running out
2. Air Filter clogged
| 1. Refill
2. Clean
PATTERN RUNS/SAGS
| 1. Applying too much Paint| 1. Adjust flow or increase movement of spray gun
TOO MUCH OVERSPRAY
| 1. Spray gun too far spray object
2. Too much material applied
| 1. Reduce distance
2. Decrease volume setting
PATTERN IS LIGHT & SPLOTCHY
| 1. Moving spray gun too fast| 1. Adjust material flow or increase movement of spray gun
DISPOSAL INFORMATION
Please recycle where facilities exist. Check with your local authority for recycling advice.
WARRANTY
To register your product and find out if you qualify for a free extended
warranty please go to
www.Vonhaus.com/Warranty.
Please retain a proof of purchase receipt or statement as proof of the
purchase date.
The warranty only applies if the product is used solely in the manner
indicated in the Warnings page of this manual, and all other instructions have
been followed accurately. Any abuse of the product or the manner in which it
is used will invalidate the warranty. Returned goods will not be accepted
unless re-packaged in its original packaging and accompanied by a relevant and
completed returns form. This does not affect your statutory rights. No rights
are given under this warranty to a
person acquiring the appliance second-hand or for commercial or communal use.
COPYRIGHT
All material in this instruction manual are copyrighted by DOMU Brands.
Any unauthorised use may violate worldwide copyright, trademark, and other
laws.
DECLARATION OF CONFORMITY
We
DOMU Brands Ltd 5th Floor The Tower Deva City Office Park Manchester
M3 7BFDeclare under our sole responsibility that the product:
SKU: 3515387
Description: VonHaus 800W Paint Station
To which this declaration relates is in conformity with the following
directives:
2006/42/EC, 2014/30/EU, 2011/65/EU