Versa G084 Automatic Single Watch Winder With Sliding Cover Instruction Manual

Versa G084 Automatic Single Watch Winder With Sliding Cover

Instruction

Thank you for purchasing a Versa watch winder. Please take a few minutes to read through the manual to ensure proper operation.

Specification

• Power        AC adapter DC/4V 550mA
• Size          5.24 x 6.26 x 5.79 inch (W x H x D)
• Weight      About 1.30 Ib (without adapter)
• Temperature  Operate between 41°F ~ 104°F
• Accessory      AC adapter

Place the watch holder into the winder. Push until you hear a “CLICK” signifying that it is securely in the winder.

Feature

1. Wind clockwise, counterclockwise, Auto(bi-directional) by operating the switch.
2. TPD (Turns Per Day)

650TPD – 850TPD – 1050TPD – 1250TPD Please note that the watch winder will turn, rest, and turn again for each setting. The watch winder will not turn constantly to prevent over winding of your watch. This is the normal operation for the watch winder.

Operation

1. Insert the adapter into the socket located on the product and plug it into the electrical outlet.
2. Open the front cover, then use your index finger and thumb to hold the watch holder from the two sides of the holder hitch marked with two arrows. With some force, pull out the watch holder.
3. Place the watch on the holder by pushing in the spring on the back of the holder, then put your watch around the holder and let go of the spring.
4. Once the watch is on the holder, place the holder back into the winder. Push until you hear a click signifying that it is securely in the winder.
5. Press Power switch to start using the winder.
6. Slide Direction switch to select clockwise, counterclockwise or Auto(bi-directional) winding direction.
7. Slide TPD switch to select the TPD .

Attention

• If you do not use this product for a long time, please switch off the unit.
• Make sure to turn the unit off completely before attempting to pull out the watch holder.

NOTE

• Please use the AC adapter supplied with the unit. Input: AC/100-240V, 50-60Hz Output: DC/4V 550mA
• Remove the adapter when the winder is not in use.
• Always turn off the power when inserting or removing watches.
• Don’t shake the watch winder when the winder is in operation.

VVe’re Here Ta Help!

www.versawatchwinders.com/contact_us.php support@versawatchwinders.com

Tips far your new watch winder

All automatic watches have different TPD requirements but on average most automatic watches need a minimum of 650-1200TPD. All of our watch winders are set to accommodate this minimum requirement. To find the right setting for your watch we recommend the following procedure:

1. Manually wind the watch by turning the crown 20-30 times. The watch winder will not wind a completely dead watch.
2. Set the winder to the lowestTPD setting and bi-directional rotation. Place the watch in the winder and make sure it is seated prop­erly and securely in the holder.
3. Turn the winder on and periodically check to make sure the time is correct. Most automatics have a maximum of 40 hours of power reserve when fully wound so if the time is correct after 2 full days, this is the proper setting for your watch.
4. If the time is incorrect, please set it to the next highestTPD setting and try again.
5. If the time is incorrect, please set it to clockwise only and try again.
6. If the time is incorrect, please set it to counter-clockwise only and try again.
7. If the watch works while it is being worn but does not work in the winder, it may need to be serviced. When a watch is worn, the movements it experiences are not as smooth as in a watch winder, so while a watch may work when its worn it may not work when in the winder. Watch winders move very smoothly so if the lubrication inside the watch has congealed from not being in use, the watch may need to be serviced.
8. If you still have problems or issues please feel free to contact us

Below is a list of popular watch brands and common settings for most of their watches. Specific models from some brands may have exceptions and may not work on the setting listed below. lfthis is the case please contact us and we will try to determine the correct setting for your particular model.

Share Your Honest Review To Help Others Make a Purchase Decision
Step 1 – Find the product you purchased on Amazon.com
Step 2 – Click on customer reviews
Step 3 – Click on “Write a customer review”
OR
Step 1 – Visit Amazon.com and login to your account
Step 2 – Goto “Orders”
Step 3 – Find the item and click on “View Details” and click on “Write a product review”

If you purchased from another website, please visit the website and post your product review on their website.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>