king electric PAW2022-W PAW Pic-A-Watt Electric Wall Heater Instruction Manual
- June 3, 2024
- KING ELECTRIC
Table of Contents
- king electric PAW2022-W PAW Pic-A-Watt Electric Wall Heater
- IMPORTANT INSTRUCTIONS
- SELECTING HEATER LOCATION
- PAW INSTALLATION INSTRUCTIONS
- PAW WIRING DIAGRAMS
- SMART LIMIT PROTECTION & WARRANTY
- TROUBLESHOOTING GUIDE
- REMOTE WALL THERMOSTAT INSTALLATION
- ABOUT COMPANY
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
king electric PAW2022-W PAW Pic-A-Watt Electric Wall Heater
DANGER
- ELECTRIC SHOCK OR FIRE HAZARD
- READ ALL WIRE SIZING, VOLT AGE REQUIREMENTS AND SAFETY DATA TO AVOID PROPERTY DAMAGE AND PERSONAL INJURY
WARNING
Read Carefully – These instructions are written in an effort to prevent
potential difficulties that might arise during installation. Studying the
instructions first may save you considerable time and money later. Observing
the following procedures will keep installation time to a minimum.
IMPORTANT INSTRUCTIONS
When using electrical heating appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
-
Read all instructions before wiring or using this heater.
-
WARNING: This heater is hot when in use. To avoid burns, don’t let bare skin touch hot surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, boxes, etc., & curtains at least 3ft (.9 m) from front of the heater and keep them away from the sides and rear.
-
CAUTION: Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
-
Do not operate any heater after it malfunctions. Disconnect power at service panel and have heater inspected by qualified electrician for repair before reusing.
-
Do not use outdoors.
-
WARNING: To disconnect heater, turn controls to OFF, and turn OFF power to heater circuit at main disconnect panel.
-
WARNING: Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, fire, or damage to the heater.
-
Do not block air intakes or exhaust in any manner.
-
Do not use it in areas where gasoline, paint, or flammable vapors or liquids are used or stored.
-
WARNING: Use this heater only as described in this manual.
Any other use is not recommended by the manufacturer and may cause fire, electric shock, explosion or injury. -
All electrical work and materials must comply with the National Electric Code (NEC), the Occupational Safety and Health Act (OSHA), and all state and local codes.
-
Use copper conductors only .
-
Verify that the electrical supply wires are the same voltage as the rating label on the front of this heater.
-
Heater must be installed in a wall can.
-
DO NOT select a location where it is likely to be blocked by furniture, curtains, etc.
-
Be sure the location selected allows sufficient space for the heater as shown by Table 1.
-
Connect grounding lead to grounding screw provided. Keep all foreign objects out of heater.
SELECTING HEATER LOCATION
DO NOT install less than 6″ (15cm) from vertical side walls or open edge of door. This heater must have an unrestricted airflow. DO NOT select a location where it is likely to be blocked by furniture, curtains, etc. Be sure the location selected allows sufficient space for the heater as shown by Table 1. DO NOT locate this heater in an area where combustible vapors, gases liquids, or excessive lint, dust or moisture is present.
PAW INSTALLATION INSTRUCTIONS
DANGER
ELECTRIC SHOCK OR FIRE HAZARD
READ All WIRE SIZING, VOLTAGE REQUIREMENTS ANO SAFETY DATA TO AVOID PROPERTY
DAMAGE AND PERSONAL INJURY
The wire and breaker sizing chart will give a general rule of installation
size. Consult an electrician if you are not knowledgeable about wiring codes.
Wire and Breaker Sizing:
Total Amps
| Minimum AWG. Wire Size (Copper| Circuit Breaker or Fuse Size
---|---|---
0 thru 12| #14| 15 amp
12.1 thru 16| #12| 20 amp
16.1 thru 24| #10| 30 amp
INSTALLATION STEPS
- Connect heater only to the voltage, amperage and frequency specified on the nameplate.
- Wiring procedures and connections shall be in accordance with all
- National and local codes having jurisdiction.
- Loosen mounting screw and remove fan heater assembly.
- A knockout of 1 /2 inch conduit size (7 /8 inch/ 2.2cm) is provided in the back & side of heater for power to enter. Provide proper strain relief connectors for wire entering the wallbox.
- Install wall box a minimum of 6″ from vertical sidewalls and 4″ above floor. The front edge of wall can MUST extend 1/2″ beyond finished wall surtace.
- Secure wallbox to the 2 x 4 stud using the two (2) holes on the side of wallbox. Secure to wall stud on opposite side if required using New Construction Bracket. See Fig. 5.
- Connect supply wires, attach ground feed wire to the green ground wire with wire nuts.
- Reinstall heater into wallbox with screw at top of interior.
- Install grill securely with screws provided in packet.
- Test unit by turning thermostat up past room temperature. You will see a puff of smoke as the elements are energized and the fan turns on. This is a normal burn off of manufacturing lubricants and will dissipate in 5 minutes.
- Heater will run until the room temperature you set is reached and then turn itself off until the temperature drops again.
- CAUTION – High temperature, Risk of Ure, keep electrical cords, drapery, furnishings, and other combustibles at least 3 feet (0.9 m) from the front of the heater as well as away from the side and rear. To reduce the risk of fire, do not store or use gasoline or other flammable vapors and liquids in the vicinity of the heater.
Rating Label Location
PAW WIRING DIAGRAMS
WATTAGE SELECTION
- The heater is factcry wired to 1500 Watts at 120 Volts. To reduce wattage unplug an insulated push on terminal per color coding below.
- Wrap with electrical tape to prevent possibility of electrlcal contact with other parts.
WIRE COLOR CODING
-
A Orange Disconnects the 750 Watt element
-
B Blue Disconnects the 500 Watt element
-
C Yellow Disconnects the 250 Watt element
-
D Black DO NOT DISCONNECT (Common} w
END VIEW OF ELEMENT- A – 750W
- B- 500W
- C- 250W
- D – Common Lag of Power Supply
WIRE COLOR CODING
-
A Orange Disconnects the 1000 Watt element
-
B Blue Disconnects 1he 750 Watt element
-
C Yellow Disconnects the 500 Watt element
-
D Black DO NOT DISCONNECT (Common)
END VIEW OF ELEMENT- A-1000W
- B-750W
- C-500W
- D – Common Leg of Power Supply
SMART LIMIT PROTECTION & WARRANTY
Heater Safety Limit Tripped?
This heater is equipped with a thermal overload Smart Limit Protection which
disconnects elements and motor In the event normal operating temperatures are
exceeded. If thermal overload trips due to abnormal operating temperatures,
thermal overload shall remain open until manually reset by turning the heater
OFF for fifteen minutes. Inspect for any objects on or PROTECTION adjacent to
the heater that may cause high temperatures. After inspecting the heater, keep
the power to the heater off for 15 minutes to reset the SLP thermal protector.
If the SLP thermal protector shuts the heater off again, immediately turn the
heater OFF at the circuit breaker and Inspect the heater for possible fan
motor failure or dirt and lint on the heating element. Repeat the starting
procedure. DO NOT TAMPER OR REMOVE THIS THIS DEVICE
Maintenance & Warranty Information:
The high quality and superior design of this heater will provide years of
trouble-free performance. Each year the heater should be checked and cleaned
for lint and dust accumulation. We recommend using a soft bristled brush such
as a paint brush to assist in removing contaminants from the heater.
Limited Year Warranty:
King Mfg. Co. will repair or replace without charge any King product found to
be defective or malfunctioning during the first 5 years of purchase to the
original owner.
TROUBLESHOOTING GUIDE
REMOTE WALL THERMOSTAT INSTALLATION
Connection Diagram for Wall Mounted Single Pole Thermostat
- Red thermostat wire to black power supply wire.
- Black thermostat wire to black heater wire.
- White power supply wire to white heater wire.
- Connect all bare ground wires together
Connection Diagram for Wall Mounted Double Pole Thermostat
- Connect the two red thermostat wires to the black and white power supply wires.
- Connect the two black wires to the black and white heater wires.
- Connect all the bare ground wires together.
We’re Here to Help!
For any difficulties installing or operating this product
- Call Us Toll Free at:
- 1-800-603-5464
- 7:00 am -3:30 pm PST Mon-Fri
- Visit king-electric.com or email us at info@king-electric.com
ABOUT COMPANY
- KING ELECTRIC MFG CO 9131 10TH AVENUE SOUTH SEATTLE,
- WA 98108
- PH:206 762 0400
- FAX 206 763 7738
- www.king-electric.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>