2Boom BX215 4-Inch LED Flame Light Speaker User Manual

June 5, 2024
2Boom

2Boom BX215 4-Inch LED Flame Light Speaker User Manual
2Boom BX215 4-Inch LED Flame Light Speaker

ACCESSORIES

  • Wireless Speaker Box
  • Microphone
  • Charging Cable
  • User Manual
  • Warranty Card

DESCRIPTION OF PARTS

  1. RGB light mode / Long-press can close or open the light
    RGB

  2. EQUALIZER mode: Normal / Pop / Rock / Jazz / Country EQ

  3. Volume+

  4. Volume-

  5. Previous song

  6. Next song

  7. Speaker modes button(Mode1:Bluetooth; Mode2:FM; Mode3:USB/TF) / Long-press toconnectTWSMode TWS

  8. Play/Pause/SCAN(Auto search in FM mode) / Long-press to connect or disconnect theBluetoothPlay/Pause/SCAN:

  9. Microphone slot

  10. OFF/ON

  11. Mirco USB Charging port (DC 5V)

  12. Charging LED

  13. Micro SD(TF) card slot

  14. USB slot

HOW TO CONNECT THE WIRELESS SPEAKER

Turn on the speaker and switch it to Bluetooth mode. Search for Bluetooth devices from mobile or other Bluetooth enabled devices. You will find “2BOOM- BX215” to pair the devices. Once paired first time, it will automatically connect after the unit is turned on.

WIRELESS

Turn on the speaker and it will come into the Wireless mode directly. After pairing the device, it can play music. Press “ ” button to Play/Pause. Press ” ” or ” ” button to be previous track or next track,press “VOL+” or “VOL-” button to increase or decrease the Volume.

USB/TF CARD

Insert the USB flash memory or TF card into the USB/TF slot, the speaker box will read the MP3 format music automatically. Press “ ” button to Play/Pause. Press ” ” or ” ” button to be previous track or next track, press “VOL+” or “VOL-” button to increase or decrease the Volume. PS: The memory size of USB / Micro SD devices which can be supported up to 32GB.

FM RADIO

Press /SCAN to search FM channels automatically. This operation will scan all FM stations and Prerecord them to memory. The scan procedure will take several minutes and cannot be interrupted. Once completed, press ” ” or ” ” button to be previous track or next track, press “VOL+” or “VOL-“buttonto increase or decrease the Volume.

RGB LIGHT MODE

There are three different RGB light modes. Short press “LED” button to switch between different RGB modes. The last used RGB light mode will be stored in the speaker memory before switching it off,and it will be restored once the speaker unit is powered on the following time. Long press the LED button can open/close the light.

EQ MODE

There are five different EQ modes. Press “EQ” button to switch between different EQ modes, suchas Normal / Pop / Rock / Jazz / Country.

TWS

Two same model speakers can be connected to one wireless device at the same time. First, turn the speakers on, then choose one unit and long press its “MODE” button for several seconds; then you will hear the sound to indicate that the two units have paired successfully. Please ensure before pairing that the two units are not connected with other devices.

CHARGING

Power off the unit, put the provided charge cable into the charge slot of unit, connect the other end to PC or other charger with 5V output (Not included). The RED LED indicator on panel will be lit when the unit is charging. When it full the RED LED light will close.

SPECIFICATIONS

Speaker size: 4 inch
Speaker output: 8W
Battery Capacity:2000mAh
Frequency Response: 100Hz-20kHz

LED LIGHT STATUS

Status Blue light Red light
Quick flashing Searching blue-connect FM SCAN /
Slow flashing Playing /
Long bright Pause / No music playing Charging

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible  for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance of 20 cm the radiator your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals