DIGITUS DS-55510 4K HDBase 1×4 HDMI Extender Splitter Set 150 m User Manual

DIGITUS DS-55510- 4K- HDBase -1×4- HDMI- Extender -Splitter -Set -150

m

Introduction

The DIGITUS® 4K HDBaseT™ HDMI Extender Splitter Set distributes the input signal on up to four output devices over a distance of up to 120 m (4K/60Hz, 4:4:4) or up to 150 m (Full HD, 1080p/60Hz) using a CAT6/7/8 cable. Supports IR and RS232 signal transmission, audio extraction (digital/analog) and EDID management. Thanks to PoC functionality, only the transmitter needs to be externally supplied with power. Using the HDMI loop-out to the transmitter unit, a local monitor can be connected in order to control the output to the receiver.

Main Features

• Supports HDBaseT™ 1.0 via CAT6/7/8 cable up to 150 m
• Supports 4K2K/60Hz (4:4:4)
• Maximum transmission distance (UHD 4K2K): 120 m
• Maximum transmission distance (Full HD 1080p): 150 m
• EDID management
• HDMI loop-out to the transmitter unit
• PoC (Power over Cable) – Only the transmitter unit requires an external power adapter
• Video bandwidth: 18 Gbps
• HDCP 2.2 / 1.4
• R232 signal transmission

Package Contents

• 1x HDBaseT™ extender splitter (transmitter unit)
• 4x HDBaseT™ receiver
• 5x IR transmission cables (1.5 m)
• 5x IR receiver cable (1.5 m)
• 1x Power adapter (DC 24V/2.7A, 1.45 m)
• 5x 3-pin Phoenix connector
• 5x 5-pin Phoenix connector
• 10x Mounting plate
• x User manual

Specification

Technical

HDMI Compliance| HDMI 2.0b
HDCP Compliance| HDCP 2.2/1.x
Video Bandwidth| 594MHz/18Gbps
Video Resolution| Up to 4k2k@60Hz 4:4:4
Color Depth| 8-bit,10-bit,12-bit(1080p@60Hz) 8-bit (4K2K@60Hz YUV4:4:4)

8-bit,10-bit,12-bit (4K2K@60Hz

YCbCr 4:2:2/4:2:0)

Color Space| RGB 4:4:4, YCbCr 4:4:4 / 4:2:2 / 4:2:0
HDR| Support HDR, HDR10+, HLG,

Dolby vision

HDMI Audio Formats| LPCM 2.0/2.1/5.1/6.1/7.1,

Dolby Digital, Dolby TrueHD, Dolby Digital Plus (DD+), DTS-ES,

DTS HD Master, DTS HD-HRA, DTS-X

Coaxial Audio Formats| PCM2.0, Dolby Digital / Plus,

DTS 2.0/5.1

Analog Audio Formats| PCM 2.0CH
ESD Protection| Human body model

±8kV (Air-gap discharge) &

±4kV (Contact discharge)

Connections

Input| 1× HDMI Type A (19-pin female)
Output| 1× HDMI Type A (19-pin female） 4x HDBaseT OUT [RJ45]

1x Coaxial Audio OUT [RCA]

1x L/R Audio OUT [5-pin phoenix

connector]

Control| 1× RS-232 (3-pin phoenix connector） 1x EDID DIP switch [5-pin]

1x IR IN [3.5mm Stereo Mini-jack]

1x IR OUT [3.5mm Stereo Mini-jack]

Mechanical
Housing| Metal Enclosure
Color| Black
Dimensions| Transmitter: 220mm (W) × 130mm (D) × 40mm (H)

Receiver: 140mm (W) × 65mm (D) × 18mm

(H)

Weight| Transmitter: 853g

Receiver: 246g

Power Supply| Input: AC100 – 240V 50/60Hz, Output: DC 24V/2.7A

(US/EU standards, CE/FCC/UL certified)

Power Consumption| 35W
Operating

Temperature

| 0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature| -20°C ~ 60°C / -4°F ~ 140°F
Relative Humidity| 20~90% RH (non-condensing)

Operating Controls and Functions

Transmitter
Front Panel

red power LED will be on.

2| IN LED| When the HDMI IN port connects an active source device, the green LED

will be on.

3| LOOP LED| When the HDMI LOOP OUT port connects an active display device, the

green LED will be on.

4| OUT (1~4) LED| When the HDBT OUTPUT port connects an HDBaseT Receiver, the corresponding green OUT LED will be

on

Rear Panel

cable for three functions:

1.      Firmware update;

2.      Control the Splitter via RS-232 commands;

3.      RS-232 signal pass-through (from transmitter to receiver or

from receiver to transmitter)

2| IR IN| Connect to IR receiver cable, the IR receive signal will emit to “IR OUT” port

of the HDBaseT Receiver

3| IR OUT| Connect to IR blaster cable, the IR emit signal is from “IR IN” port of the

HDBaseT Receiver

4| AUDIO OUT (COAX, L/R)| Coaxial/balanced audio output port, connect to amplifer or

speaker

5| POWER switch| Press this switch to power on/off the

device

6| EDID DIP

switch

| Used to set EDID mode. Please refer to Section “6. EDID

Mode” for details

---|---|---
7| HDMI port| IN: HDMI input port, connect to HDMI source device such

as DVD or set-top box with an HDMI

cable

LOOP OUT: HDMI loop output port, connect to the HDMI

display device such as TV or Monitor

with an HDMI cable

8| HDBT OUTPUT

port (1~4)

| Connect to the HDBT IN port of the

HDBaseT receiver with a CAT cable

9| Connection Signal Indicator lamp (Green)| ·    Illuminating: Transmitter and Receiver are in good connection status

·    Flashing: Transmitter and Receiver are in poor connection status

·    Dark: Transmitter and Receiver are not connected

10| Data Signal Indicator lamp

(Orange)

| ·    Illuminating: HDMI signal with HDCP

·    Flashing: HDMI signal without HDC

·    Dark: No HDMI signal

11| DC 24V| Plug the DC 24V power supply into the unit and connect

the adaptor to an AC outlet ( Note: The transmitter can

power the receiver via a CAT cable)

IR Pin Definition HDBaseT Receiver

be on

2| SERVICE port| Used for firmware update
3| DC 24V| Plug DC 24V/1A power supply into the unit and connect

the adapter to an AC outlet.

( Note: The HDBaseT receiver also can be powered by the

transmitter via a CAT cable)

4| HDBT IN| Connect to the HDBT OUTPUT port on the transmitter

with a CAT cable

5| Connection Signal Indicator lamp (Green)| ·    Illuminating: Transmitter and Receiver are in good connection status

·    Flashing: Transmitter and Receiver are in poor connection status

·    Dark: Transmitter and Receiver are not connected

---|---|---
6| Data Signal Indicator lamp (Orange)| ·    Illuminating: HDMI signal with HDCP

·    Flashing: HDMI signal without HDCP

·    Dark: No HDMI signal

7| HDMI OUT| HDMI output port, connect to HDMI display device such

as TV or Projector with an HDMI cable

8| AUDIO OUT| Audio output port, connect to amplifer or speaker
9| IR IN| Connect to the IR Receiver cable. The IR signal will send

to the IR OUT port of the transmitter

10| IR OUT| Connect to the IR blaster cable, the IR signal is from IR

IN port of the transmitter

11| RS-232| 3-pin Phoenix connector for RS-232 command

transmission. The RS-232 command will pass-through

from transmitter to receiver or from

receiver to transmitter

IR Receiver and Blaster pin’s definition is as below:

Note:
When the angle between the IR receiver and the remote control is ± 45°, the transmission distance is 0-5 meters; when the angle between the IR receiver and the remote control is ± 90°, the transmission distance is 0-8 meters.

EDID Mode

The defined EDID setting list of the product is shown as below:

ASCII Commands

The product also supports ASCII command control. Connect the RS-232 port of the product to a PC with a 3-pin phoenix connector cable. Then, open a Serial Command tool on PC to send ASCII commands to control the product. The ASCII command list about the product is shown as below.

ASCII Commands

Serial port protocol.

Baud rate: 115200, Data bits: 8bit, Stop bits:1, Check bit: 0

x – Parameter 1 y – Parameter 2

! – Delimiter

Command Code| Function Description| Example| Feedback| Default Setting
s power z!| Power on/off the device, z=0~1 (z=0 power off, z=1 power on)| s power 1!| Power on System Initializing… Initialization Finished!

FW version

x.xx.xx

| power on
r power!| Get current power state| r power!| power on/power off|
s reboot!| Reboot the device| s reboot!| Reboot… System Initializing… Initialization Finished!

FW version x.xx.xx

|
System Setup

help!| List all commands| help!|  |
r type!| Get device model| r type!| HDC- SPB14H150|
r status!| Get device current status| r status!| Get the unit all status: power, in/out connection, edid mode|
r fw version!| Get Firmware version| r fw version!| MCU BOOT:

Vx.xx.xx MCU APP:

Vx.xx.xx

|
r link in!| Get the connection status of the input port| r link in!| HDMI IN:

connect

|
r link out y!| Get the connection status of the y output port, y=0~5 (0=all, 1~4=HDBT 1~4, 5 = loop out)| r link out 1!| hdmi loop out: connect

hdbt output 1: connect

|
s reset!| Reset to factory defaults| s reset!| Reset to factory defaults System Initializing…

Initialization Finished!

FW version x.xx.xx

|
Output Setting
s hdmi stream z!| Set hdmi loop output stream on/off

z=0~1 (0:disable,1:enable)

| s hdmi stream 1 !| Enable hdmi loop out stream Disable hdmi loop out stream| enable
s hdmi hdcp z!| Set hdmi loop output hdcp on/off

z=0~1 (0:disable,1:enable)

| s hdmi hdcp 1!| Enable hdmi loop out hdcp

Disable hdmi loop out

hdcp

| enable
s hdbt y hdcp z!| Set hdbt output y hdcp on/off,

y=0~4(0=all) z=0~1(0:disable, 1:enable)

| s hdbt 1 hdcp 1 !

s hdbt 0 hdcp 1 !

| Enable hdbt output 1 hdcp Disable hdbt output 1 hdcp

Enable hdbt all outputs hdcp Disable hdbt all outputs hdcp

| enable
---|---|---|---|---
s hdbt y stream z!| Set hdbt output y stream on/off, y=0~4(0=all) z=0~1 (0:disable,1:enable)| s hdbt 1 stream 1 !

s hdbt 0 stream 1 !

| Enable hdbt output 1 stream Disable hdbt output 1 stream

Enable hdbt all outputs stream Disable hdbt all

outputs stream

| enable
r hdmi stream!| Get hdmi loop out stream

status

| r hdmi stream!| Enable hdmi output stream|
r hdmi hdcp!| Get hdmi loop out hdcp status| r hdmi hdcp!| Enable hdmi output

hdcp

|
r hdbt y hdcp!| Get hdbt output y hdcp status,

y=0~4(0=all)

| r hdbt 1 hdcp!| Enable hdbt output 1 stream|
r hdbt stream!| Get hdbt output y stream

status, y=0~4(0=all)

| r hdbt 1 stream!| Enable hdbt output 1 stream|
EDID Setting
s edid in from z!| Set input EDID from default

EDID z, z=1~27

1. 1080p, Stereo Audio 2.0

2. 1080p, Dolby/DTS 5.1

3. 1080p, HD Audio 7.1

4. 1080i, Stereo Audio

2.0

| s edid in from 1!| input EDID:1080p,

Stereo Audio 2.0

Please toggle EDID

dip switch to

00000!

| 1080p,

Stereo, Audio 2.0

 | 5. 1080i, Dolby/DTS 5.1|  |  |
---|---|---|---|---
6. 1080i ,HD Audio 7.1
7. 3D, Stereo Audio 2.0
8. 3D, Dolby/DTS 5.1
9. 3D, HD Audio 7.1
10. 4K2K30_444,
Stereo Audio 2.0
11. 4K2K30_444,
Dolby/DTS 5.1
12. 4K2K30_444, HD
Audio 7.1
13. 4K2K60_420,
Stereo Audio 2.0
14. 4K2K60_420,
Dolby/DTS 5.1
15. 4K2K60_420, HD
Audio 7.1
16. 4K2K60_444,
Stereo Audio 2.0
17. 4K2K60_444,
Dolby/DTS 5.1
18. 4K2K60_444, HD
Audio 7.1
19. 4K2K60_444,
Stereo Audio 2.0 HDR
20. 4K2K60_444,
Dolby/DTS 5.1 HDR
21. 4K2K60_444,
HD Audio 7.1 HDR
22. copy from hdmi loop
out
23. copy from hdbt
output 1
24. copy from hdbt
output 2
25. copy from hdbt
output 3
26. copy from hdbt
output 4
27. use user1 EDID
s edid user1 00 FF FF FF FF …!| Set user1 EDID data| s edid user1 00 ff ff ff ff …. !| user1 EDID data: 00

FF FF ….

|
---|---|---|---|---
r edid user1!| Get user1 EDID data| r edid user1!| user1 EDID data: 00

FF FF FF FF FF FF

00 ………

|
r edid in!| Get EDID status of the input| r edid in!|  |
r edid in data!| Get the EDID data of the hdmi

input

| r edid in data!|  |
RS-232 BYPASS Setting
s rs232 bypass hdbt y!| Set RS-232 port connect to

HDBT out1 Receiver RS- 232

port, y=0~5( 0=all, 1~4= hdbt out 1~4 5=NC)

| s rs232 bypass y=0 hdbt 1!| RS-232 connect to

HDBT OUT1

RS-232 not connect

to HDBT OUT

| y=0
r rs232 bypass!| Get RS-232 port connect to

HDBT out receiver RS- 232

port

| r rs232 bypass!| RS-232 connect to

HDBT OUT1

RS-232 connect to all

HDBT OUT

RS-232 not connect

to HDBT OUT

|
s device baud w size x stop y parity z!| Set receiver control device

COM port setting, w=2400, 4800,9600,19200,38400,

57600,115200, x=7,8

y=1,2, z=none, even,odd

| s device baud 57600 size 8

stop 1 parity none!

| receiver device COM

port setting baudrate: 57600

data size :8, stop:1

parity: none

|
s rs232 time x!| set send RS232 command

wait time x=200~5000ms

| s rs232 time 200!| send RS-232 command wait time

200ms

| 200ms

Application Example

Disclaimer

The terms HDMI and HDMI High-Definition Multimedia interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance. Hereby ASSMANN Electronic GmbH declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address. www.assmann.com

References

• ASSMANN Electronic GmbH | Germany

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>