SUPERATV Polaris Ranger 1000 Installation Guide

June 3, 2024
SUPERATV

SUPERATV-LOGO

SUPERATV Polaris Ranger 1000

SUPERATV-Polaris-Ranger-1000-PRODUCT

Liability Statement

SuperATV’s® products are designed to best fit user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV® and is not recommended. SuperATV’s® products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact

SuperATV® to verify that they will work together. Although SuperATV® has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of the machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product’s ability to protect user from severe injury or death. SuperATV® urges operators and occupants to wear a helmet and appropriate riding gear at all times. By purchasing and installing SuperATV® products, user agrees that should damages occur, SuperATV® will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from SuperATV®. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim.

SuperATV® will warranty only parts provided by SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other manufacturers’ products will not be covered by SuperATV®. SuperATV® parts and products are not warranted if item was not installed properly, misused, or modified. Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively legally and personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you. The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof.

Before installing self-tapping hardware, pre-drill holes with 5/32” drill bit.

PRODUCT DESCRIPTION

SUPERATV-Polaris-Ranger-1000-FIG-1

Item Description
A Front Plate
B Center Plate
C Rear Plate
D Left Side Plate
E Right Side Plate
F Left Plate
G Right Plate
H Left Plate Rear
J Center Plate Rear
K Right Plate Rear
  • disregard any extra hardware

INSTALLATION INSTRUCTIONS

  • Gently flip the machine onto its side and remove the stock Skid Plates.SUPERATV-Polaris-Ranger-1000-FIG-2
  • install Center Plate Rear (J) with hardware shownSUPERATV-Polaris-Ranger-1000-FIG-3
  • install Center Plate (B) with hardware shownSUPERATV-Polaris-Ranger-1000-FIG-4
  • install Rear Plate (C) with hardware shown
  • install Left Side Plate (D) to Left Plate (F) with hardware shown
  • install Left Plate (F) with hardware shownSUPERATV-Polaris-Ranger-1000-FIG-7
  • repeat steps for Right Plate (G)SUPERATV-Polaris-Ranger-1000-FIG-8
  • secure Left Side Plate (D) with hardware shownSUPERATV-Polaris-Ranger-1000-FIG-9
  • repeat steps for Right Side Plate (E)
  • install Left Plate Rear (H) with hardware shownSUPERATV-Polaris-Ranger-1000-FIG-10
  • repeat steps for Right Plate Rear (K)
  • install Front Plate (A) with hardware shownSUPERATV-Polaris-Ranger-1000-FIG-11
  • if SuperATV Frame Stiffener is installed, use hardware shown
  • tighten all hardware completely

Need help with your installation?

© 2021 SuperATV.com®. All Rights Reserved.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SUPERATV User Manuals

Related Manuals