BacKYard DISCOVERY 2105126COM Trenton 14 ft. x 10 ft. Black Steel Modern Pergola with Sail Shade Soft Canopy Owner’s Manual
- June 5, 2024
- BACKYARD DISCOVERY
Table of Contents
BacKYard DISCOVERY 2105126COM Trenton 14 ft. x 10 ft. Black Steel Modern
Pergola with Sail Shade Soft Canopy
WARNING
IT IS IMPORTANT TO CHECK AND TIGHTEN ALL HARDWARE AT THE BEGINNING AND DURING THE SEASON AS THEY MAY LOOSEN DUE TO EXPANSION AND CONTRACTION.
DO NOT climb or walk on the roof for any reason . Requires two or more
people to assemble safely Check for underground utilities before digging or
driving stakes into the ground. .Check carefully for overhead lines and ensure
there is at least 6ft (2m) clearance from any overhead electrical wires.
.Permanent structures may require a building permit. As the purchaser and or
installer of this product, you are advised to consult local planning, zoning,
and building inspection departments for guidance on applicable building codes
and/or zoning requirements. .Wear gloves to avoid injury during installation.
.During installation, follow all safety warnings provided with your tools and
use safety glasses. Check all nuts and bolts twice monthly during the usage
season and tighten as required. It is particularly important that this
procedure be followed at the beginning of each season. Oil all metallic moving
parts monthly during the usage
period. Check all coverings for bolts and sharp edges twice monthly during
usage season to be certain they are in place. Replace when necessary. t is
especially important to do this at the beginning of each new season. For
rusted areas on metallic members such as hinges, brackets, etc. sand and
repaint, using a non-lead-based paint meets the requirements of Title 16 CRF
Part 1303. Touch-up paint is available through Backyard Discovery. Please have
the product number tag available for reference for customer support. This
ensures the correct color will be provided.
OWNERS SHALL BE RESPONSIBLE FOR MAINTAINING THE LEGIBILITY OF THE WARNING LABELS
Assembly Tips &Tools Required
ASSEMBLY TIP: keep an eye out for these boxes which will contain helpful
pictures and information making the assembly process as quick and painless as
possible.
When removing
the parts from the boxes we recommend arranging them by part number before you
begin assembly. This will allow for faster assembly and easily identify any
parts that may be missing or damaged.
Hardware Identification
Hardware is identified with a seven digit alpha-numeric part number. During
assembly you only need to reference the last three digits of the part number
as noted in each step. This will make finding the correct hardware easier
.
Tools Required
Some steps in the assembly process will require a second set of hands. Make sure you have a helper available.
For proper assembly you will need to ensure that your structure is level
before proceeding to the next step.
A ladder will be needed for assembly. DO NOT stand or climb on any part of the
structure at any point. Doing so may result in injury.
A Phillips head screw driver will be used in an assembly step.
You will need to make sure that your assembly is square before fully
tightening your bolts.
A tape measure may be needed to check overall dimensions to ensure structure
is square.
A rubber mallet may be useful during the assembly process.
A drill and concrete drill bit will be used in an assembly step.
Basic Setup Dimensions & Assembly Notes
-
It is critically important that you start with square and level footings, concrete pad or deck to attach your structure
Pay close attention to the items needed for each step. Make sure you are using the correct hardware for each step. Using incorrect hardware may result in improper assembly -
Remember to double-check for underground utilities and overhead electrical lines
Post mounts are provided with your structure which allows you to permanently install your structure to a pre-existing or new wood or concrete surface.
- The hardware to attach the post mounts to the structure is inluded.
- The hardware to mount the structure permanently to a concrete surface is NOT included.
- The hardware to mount the structure permanently to a wood deck is NOT included and will need to be purchased separately. You must ensure there is ample structural support under the deck before permanently attaching.
Metal Roof Assembly
Remove plastic covering from metal roof panels before installing each piece.
Place roofing materials on a nonabrasive,
flat surface before and after assembly as it could bend, dent or scratch
Overall Dimensions
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>