Akuvox E12 Compact Door Intercom User Guide
- June 4, 2024
- Akuvox
Table of Contents
Smart Intercom
E12
Quick Guide
Unpacking
Before you being using the device, please check the version you obtained and
ensure that the following items are included in the shipped box:
Universal Accessories:
| E12 x 1
---|---
| Wall mounting bracket x 1
| ST4x20 screw x 4
| Torx screw x 2
| Plastic Wall Anchor x 4
| Back cover x 1
| 7-pin cable x 1
| Wall-mounting template x 1
| M3x4 screw x 4
| Torx Wrench x 1
| 6-pin cable x 1
| Diode x 1
Product Overview
Installation Environment
Indoor and outdoor installation are supported.
If installing the device outdoors, please do not place device under direct
sunlight.
If installing the device indoors, please keep device at least 2 meters away
from light, and at least 3 meters away from the window and door.
Installation
According to the position of the reserved wires on the wall, stick the wall-
mounting template vertically to ensure that the wires can come out of the
shadow position of the template.
Drill (6 mm drill bit required) four screw holes with a depth of 25mm in the
screw holes of the template.| Insert four plastic wall anchors into the
holes.| Fix the wall-mounting bracket on the wall by tightening four STx20
screws to the plastic wall anchors.
Connect the wires to the interface of the device as needed (for details, refer
to “Device Wiring”).
After arranging the wires, tighten the back cover using four M3x4 screws to
the device.| Hang the device on to the two square hangers on the wall-mounting
bracket, then use the Torx Wrench attached to tighten the bottom of the device
with two Torx screws.| The installation is completed.
Application Network Topology
Device Wiring
Warning
When you connect a device containing a coil, such as a relay or an
electromagnetic lock, it is necessary to protect the intercom against voltage
peak while switching off the induction load. For this way of protection, we
recommend a diode 1 A / 200 V (included in the accessories) connected
antiparallel to the device.
IP Announcement
- While E12 starts up normally, hold the call button for several seconds after the LED light turns blue, voice system will enter IP announcement mode.
- In announcement mode, the IP address will be announced periodically.
- Press Call Button again to the announcement mode.
- In announcement mode, the phone announces “IP 0.0.0.0” if no IP address is gained.
Operation
Make a call:
- Press the call button to call the indoor SIP Phone.
- During the talk, the called party can press a pre-configured code number to unlock the door.
Receive a call: E12 supports Auto Answer by default. Incoming calls from indoor devices will be answered automatically.
Configuration
- Access the Web UI: Input the IP address into web browser to configure the phone.
- Account Registration: On web UI, go to the path: Account -> Basic page Register Account and fill in the account information. ( Please refer to user manual for more information)
- Configure the Push Button: On web UI, go to the path: Intercom -> Basic -> Push Button to configure the call number.
- Configure the code to open the relay: On web UI, go to the path: Intercom -> Relay&Input -> Relay ID/DTMF and choose the DTMF code number in corresponding area.
Indicators
| Name | Status | Description |
|---|
Status
Indicator| Blue Light Always On| Normal status
Blue Breathing Light| Calling
Receiving a call
Blue Light Always On > Red Light Always On > Purple Light Always On|
Restarting
Red Breathing Light| The network is unavailable / Obtaining network
Purple Light Always On| Talking
Red/Purple Light Flashing| Firmware upgrading
Note: For more LED settings, please refer to E12 webUI: Intercom -> LED Setting.
Notice Information
Information contained in this document is believed to be accurate and reliable
at the time of printing. This document is subject to change without notice,
any update to this document can be viewed on Akuvox’ s website:
http://www.akuvox-.com © Copyright 2021 Akuvox Ltd. All rights reserved.
http://www.akuvox.com/
AKUVOX (XIAMEN) NETWORKS CO., LTD.
ADD: 10/F, NO.56 GUANRI ROAD, SOFTWARE PARK II, XIAMEN 361009, CHINA
www.akuvox.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>