Comfort Zone 18 inch 2 in 1 Performace Stand Ultra Silence Pedestal Fan Owner’s Manual

Comfort Zone 18 inch 2 in 1 Performace Stand Ultra Silence Pedestal Fan

Features:

• Patented 18 inches plastic grid and 6 blades.
• 2 in 1 fan: Stand and wall.
• 3 speeds.
• Adjustable stand up to 53.15 in height.
• Wide area oscilation.
• Adjustable tilt head.
• 120 V~ A.C. / 60Hz

WARNING : AS ANY OTHER ELECTRIC POWERED FAN, THIS ONE CONTAINS PARTS WHICH DRIVE ELECTRICAL POWER WHILE CONNECTED, EVEN WHEN THE UNIT IS TURNED OFF.

WARNING : ELECTRICAL SHOCK DANGER

Recommendations:

• Use grounded outlet only
• Do not use any external connections, adapters or timers.
• Do not overcharge the electrical power socket where you connect this household.
• Always set the fan on a dry, flat and steady surface. Do not handle this fan when having your hands wet. Before you connect the fan to the electrical power, make sure both the cord and the socket are completely dry.
• Do not submerge on water or any other liquid. DO NOT USE THE FAN IF IT FELL INTO WATER.

IMPORTANT SAFETY GUIDELINES

• Avoid any contact with the moving parts of this fan. Keep your hair, hands and feet away from the moving parts of the “stand fan”.

• Please keep this fan away from children or people with any mental or physical disability, as well as away from those people who has not received the proper instruction on the use of this fan.

• Please be aware of your children when the “stand fan” is in use. Do not allow children to play near the fan. Please make sure to unplug from the electrical power the fan every time you finish using it and before clean it. Make sure to use only a 120 Volts electric source. Do not use the “stand fan” if you detect any damage on the unit or the electrical power cord.

• Do not use the “stand fan” if the unit has fallen down and become damage in any way. Please take the unit to your nearest authorized service center, so that it can be repair, check or adjust.

• Do not let the “stand fan” to enter in contact with water or any liquid.

• Do not use this fan outside.
  Always set the “stand fan” on a plain, stable surface in order to avoid it to fall.
  Vacuum dust and residuals from the grid and the blades after unplugging the “stand fan”.

• Do not operate the “stand fan” without the grids set. Make sure to turn off the fan whenever unattended. Always remember to unplug from the electric power supply.

• Never leave the fan unattended while plugged in. If the electrical connection, cord or plug are damaged, they must be repaired by the manufacturer directly or by someone from an authorized service center. Never use the fan if it is damaged on any way, either the unit itself or its cord and plug.

• Keep away the electrical connection cord form sharp edges, as well as away from the moving parts of the “stand fan”.

• Do not use the fan if it has fallen down and any damaged has been determined.

• Never set the fan on wet floor and never mop around the fan itself when operating.

• This fan is not a toy, keep away from children.

Parts identification 1

A.-ST 3x8mm W/Washer Screw: This screw is used to fit the rear grill to the fan motor cover and is placed before putting the propeller on the motor shaft.

**Parts identification 2

**

1. Front grid
2. Back grid
3. Safety grid’s fixing locks
4. Fan blades
5. Motor shaft
6. Blades nut.
7. Engine body.
8. Swing pivot
9. Manual operation Speed/Off/Pilot Light
10. Pilot light/Night light
11. Control panel
12. Telescopic tube
13. Height fixing rings
14. Fixing knob
15. Base
16. Counterweight
17. Washer
18. L screw
19. Wall support attachment

ASSEMBLY INSTRUCTIONS

Fan assembly:

Set the back grid on the motor shaft, make sure thatthe internal arrow (as it is draw in the enhancement within Fig. B) points up and the 4 central clips fit. You might push firmly in order to make them tightly fit. Once the 4 clips have been set, make sure they are tight (Fig. C).

Take the 3×8 mm W/ Washer screw (A) from your kit and screw it with the help of a Phillips screwdriver over the cylinder-shaped housing that is seen at the top of the grill. (Fig. D)

Set the fan blades correctly on the engine body and screw the blades nut towards the word “THIGHTEN” as the arrows show. (Fig. E)
Join the front and back grills together by aligning the 6 fixing clips and push firmly until a “click” sound is heard (Fig. F).

Take the M3mm nut (C) from your kit and place it on the hex socket at the bottom of the rear grille (Fig. G), then take the M3x20 mm screw from your kit and put it on the socket on the bottom of the front grille. With the help of a Phillips screwdriver, screw the nut to secure both racks (Fig. H).

Mounting the base:

Unscrew the L screw from the telescopic tube washer. Set the tube inside the base’s round space.
Set the counterweight at the bottom of the base.
Set the washer under the counterweight so that the domed part keeps touching the counterweight.(Fig. I)
Screw clockwise the L screw into the washer hole holding the telescopic tube until it is firmly tight into the base. (Fig. J)
Stand assembly:
Screw the height fixing ring counter clockwise and lift the stand internal tube until it reaches the desired height. The maximum fan height is 53.15 in.
Screw the height fixing ring clockwise until it is safely tight in order to fix the fan´s height.
Unscrew the fixing knob and fit the telescopic tube inside the engine body set (motor, blades and grids).
Make sure to reach the bottom of the base and screw the fixing knob clockwise until it is firmly adjust.

Assembling the wall support attachment:

By using a 1/4” drill (not included) make two holes horizontally aligned with 1.57 in of separation (it is not recommended to install the wall support attachment on prefabricated walls or not stable walls).

Insert in every hole a 1/4” plastic dowel (included), then insert in each plastic dowel a 1/4” x 1” screw (included) no more than 2 cm deep (S1).
Set the previously ensemble body with grids and blades on the wall support attachment (S2) and tight it from behind with the fixing knob (S3).
Finally set the display on the previously set wall screws (S4) and make sure it is properly set (S5).

Swing pivot:
The swing pivot may not be assembled to the engine body. Find the swing pivot inside one of the plastic bags that contain parts of the fan. Introduce the pivot inside the engine body hole assigned for it and push down firmly until a “click” sound is heard and make sure the pivot is correctly assembled. (Fig. K)

Operation mode

• Make sure to set the fan on a stable and firm surface, avoid rugs or carpets where it can tangle. Make sure the unit is properly plugged to the electric power supply, not before you verify the appliance is off.
• In order to start the fan push the speed button desired: 1=Low; 2=Medium; 3=High
• In order to refresh large rooms, our recommendation is to use oscillating mode by pulling the swing pivot upwards to start oscillation and pushing down again to stop it.
• The fan’s head angle can be horizontally adjusted by pulling the swing pivot upwards so that it will move on 150 oscillation range so you can set it to the desired position by pushing the pivot down in. Make sure before starting the operation of the fan than it is set more than 3.94 in away from any strange object which may block the air flow, such as a walls, curtains or furniture.

ATTENTION: Make sure to turn off the fan by pushing the off button “0”, before you decide to move it to another place.

Pilot light / Night light
The pilot light helps you locate the fan on the darkness. You turn it on by pushing the button “L” once, as you turn it off by pushing the off button “0” once.

CLEANING AND MAINTENANCE

• Remember to unplug the fan from the electric power supply every time after finishing using it.
  In order to clean the fan exterior make sure to use a dry piece of cloth lightly wet with a soft liquid soap. Never submerge the fan in water or any other fluid, nor let any water leak into the inside of the fan. Avoid using either corrosive or flammable substances such as gasoline, thinner, etc. since this damage the fan and produce toxic vapors, as well.

• We recommend to follow these steps in order to clean the blades:

  1. Remove the front grid.
  2. Clean the blades with a dry piece of cloth lightly wet with a soft liquid soap.
  3. Make sure to put back the safety grill’s fixing locks and that these firmly holds both grills (front and back). Make sure the fan is completely dry before starting it again.

STORAGE

Make sure to turn the “stand fan” off. Make sure the blades of the “stand fan” are completely stopped. Make sure not to tangle around the appliances the electric power cord, roll it in circles without forcing it. Storage both appliances in a clean a dry space, and keep it always in a vertical position.
This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.

Fuse Replacement:

1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
2. Open fuse cover by sliding open fuse access cover on top of attachment plug towards blades. See Fig 2.
3. Remove fuse carefully. Use a small tool to pry the end of the fuse from holder cavity. Be careful not to break glass window.
4. Replace fuse. WARNING: Risk of fire. Replace fuse only with identical 2.5 or 5.0 Amp, 125 Volt fuse (3.6mm x 10mm).
5. Be sure fuse is properly seated within its cavity. Close fuse cover by sliding it back to its original closed position.

Limited Warranty

This unit is guaranteed to the original retail purchaser against defects in quality or workmanship for a period of one year from the date of original purchase. If this unit fails because of a manufacturing defect within 30 days of purchase, return the unit, with your receipt, to the retailer. After 30 days, but within the warranty period, if the unit was purchased within the continental United States, return it, freight prepaid, to World and Main for repair or replacement. If the unit was purchased outside the continental United States, return the unit to the place of purchase. This warranty does not cover damage caused by misuse, abuse, overheating or alteration. Repairs made by anyone other than World and Main are not covered in this warranty. World and Main will not be held liable for any losses due to neglectful operation. All implied warranties, including the warranties of merchantability and of fitness of purpose, if applicable, are hereby limited in duration to the period of one year from the date of original retail purchase. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. Incidental or consequential damages arising from a breach of either express or implied warranties are hereby disclaimed and excluded. Some states do not allow the exclusion of limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you. Upon the expiration of this warranty all such liability will terminate. No other warranties are expressed or implied.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. No informal dispute settlement mechanisms are available. This limited warranty is given in lieu of all other warranties.
Manufactured for :
World and Main (Cranbury), LLC
324A Half Acre Rd.
Cranbury, NJ 08512 USA
800-221-6895
www.comfortzoneproducts.com
Rev. 092718
Country of origin : MÉXICO

References

• Heaters | Fans | Comfort Zone Products – Comfort Zone, Mr. Brands, LLC.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>