sauermann CO 50 Portable CO-Meter User Guide
- June 5, 2024
- sauermann
Table of Contents
- sauermann CO 50 Portable CO-Meter
- Operating temperature, protection of the instruments and information
- Keys
- Take a measurement
- Carry out a manual autozero (MP 50, MP 51)
- Change the unit
- Select the velocity type: contact or optical (CT 50)
- Perform a self-test (HM 50)
- Batteries replacement
- Auto shut-off
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
sauermann CO 50 Portable CO-Meter
Class 50 portables
These portable instruments are used to measure the following parameters:
temperature, relative humidity, CO, pressure, air velocity and light.
Operating temperature, protection of the instruments and information
about storage
Conditions of use (°C/%RH/m): from 0 to +50 °C. In non-condensing conditions. From 0 to 2000 m. Protection: IP54
Storage temperature:
HD 50, LX 50: from -20 to +70 °C. CT 50, CO 50, HM 50, LV 50, MP 50, MP 51,
MP 55, VT 50: from -20 to +80 °C. If the instrument is stored outside the
operating temperature (for example in a van, a warehouse…), please wait for 10
minutes in its operating temperature before start using it.
Keys
Select
On/Off/Hold
Take a measurement
- VT 50: before using the instrument with the hotwire probe, please lower the protection tube (1) of the sensing element.
- VT 50: always use the hotwire probe with the red point in front of flow.
CO 50: the instrument displays its name then a 5 second countdown. This count corresponds to the preheating time of the sensor. At the end of the countdown, the measured value of CO is displayed. MP 50, MP 51: the instrument displays its name then an autozero is performed. At the end of the autozero, the measured value displays. Press briefly on “Select” to switch measurement parameter display.
MP 50, MP 51, MP 55: press briefly and successively on “Select” to change the unit.
- Available units for MP 50: Pa, mmH20, inWg, daPa.
- Available units for MP 51: mmH20, kPa, in Wg, mbar, mmHg, daPa.
- Available units for MP 55: mbar, mmHg, hPa.
HM 50: press briefly on “Select” to select a type of material. Press the spikes in the material to be measured. When a measurement is over-range, above the maximum range, the value flashes. Below the minimum range, the value is no more measurable and the device indicates it means that for:
- Wood type 1: the measurement is < than 10%
- Wood type 2: the measurement is < than 9%
- Plaster, brick and concrete: the measurement is < than 0.1%
Carry out a manual autozero (MP 50, MP 51)
During measurement:
Remove pressure tubes. Carry out a long press on “Select”. The instrument
makes an autozero then returns to the measurement display.
Hold the measurement
During measurement, press briefly on “On/Off/Hold” to hold measurement: “Hold”
appears on the screen and measurements are fixed. CO 50, HD 50, HM 50, LX 50,
MP 55, VT 50: press briefly on “Select” to move from one parameter to the
other. Press again briefly on “On/Off/Hold” to exit the Hold function.
Change the unit
The instrument is on.
CO 50, CT 50, HD 50, LX 50:
Carry out a long press on “Select” to change the unit. Press briefly on
“Select” to select the required unit of measurement. Carry out a long press on
“Select” to confirm the unit and return to the normal measuring mode.
VT 50:
Change the air velocity unit: Press briefly on “Select” up to display the air
velocity. Carry out a long press on “Select” to change the air velocity unit.
Press briefly on “Select” to select the required unit of measurement. Carry
out a long press on “Select” to confirm the unit and return to the normal
measuring mode.
Change the temperature unit:
Press briefly on “Select” up to display the temperature. Carry out a long
press on “Select” to change the temperature unit. Press briefly on “Select” to
select the required unit of measurement. Carry out a long press on “Select” to
confirm the unit and return to the normal measuring mode.
Select the velocity type: contact or optical (CT 50)
The instrument is on. Carry out a long press on “Select”: “Cont” or “Optic” flashes. Press briefly on “Select” to select contact velocity (“Cont”) or optical velocity (“Optic”). Carry out a long press on “Select” to confirm.
Perform a self-test (HM 50)
Turn the instrument on. Remove the cap and turn the cap. Press “Select” to select the type of material to verify. Press the 2 pins of the instrument into the contact plugs of the cap. Read the value indicated by the instrument:
- If the indicated value matches with the given value in the table below, the instrument runs properly.
- If the indicated value does not match with the given value in the table below, clean the tips and carry out a new self-test. If the value is still wrong, change the pins. If it does not work, please contact the after sales service.
Batteries replacement
The instrument is OFF. Remove the front part at the back of the instrument. Replace used batteries by new batteries AAA LR03 1.5 V. Replace the front. To ensure safety, replace batteries with the same type. Not doing so might lead to explosion. Dispose of used batteries according to instructions
Auto shut-off
The instrument switches off if it is not used during 20 minutes.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>