LITETRONICS FL-Series Flood Light Instruction Manual
- June 12, 2024
- Litetronics
Table of Contents
LITETRONICS FL-Series Flood Light
Product Information
The Flood Light is a high-quality lighting fixture designed for outdoor use. It is available in various models with different power capacities, including 60W, 100W, 150W, 255W, and 330W. The light comes with a yoke photocell (60W, 100W, and 150W models) and a pluggable sensor socket (150W, 255W, and 330W models) to enhance its functionality. The fixture also includes a shorting cap (255W and 330W models) for optional installation. The Flood Light is compatible with different cable lengths, as specified in the chart below. It operates at different voltage levels, including 120V, 277V, 240V, and 480V.
WHAT COMES IN THE BOX
- Yoke
- Photocell (60W, 100W, & 150W models)
- Pluggable sensor socket (150W, 255W & 330W models) Shorting cap (255W & 330W models)
- Cable (See chart below)
- Installation Instructions
TOOLS NEEDED
- Phillips Screwdriver
CABLE LENGTHS
Part Number/Length
- FL0601 1.15 Ft.
- FL1001 1.65 Ft.
- FL1501 1.65 Ft.
- FL2552 1.65 Ft.
- FL3302 1.65 Ft.
SAFETY INSTRUCTIONS AND WARNINGS
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE OBSERVED. READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
- Litetronics fixtures must be wired in accordance with the National Electrical Code and all applicable local codes.
- Risk of fire or electric shock. Flood light installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- Be certain electrical power is OFF before and during installation and maintenance.
- Flood light must be connected to a wiring system with an equipment – grounding conductor.
- Make sure the supply voltage is the same as the rated luminaire voltage.
Only the open holes indicated in the photographs and/or drawings may be made or altered as a result of this kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components.
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet
metal or sharp objects.
Suitable for wet locations.
ATTENTION’
- Please check if there is any damage during shipping. If so, please contact Litetronics customer service.
- Please read the installation instruction carefully to check whether all the accessories are included.
- After confirmation, install the fixture according to installation steps.
INSTALLATION PROCEDURE
WIRING DIAGRAM
Warning: Min. 75 °C supply conductors. 60W, 100W and 150W models suitable for operation in ambient not exceeding 50°C.
FUNCTION ADJUSTMENTS (60W, 100W, 150W MODELS)
- Open the metal plug and plastic plug counterclockwise with a screwdriver (Figure 3) , then slide the switch up and down to adjust the power controller, CCT selector or photocell controller for your application. (Figure 4)
- After adjusting the required control function(figure 5), tighten the metal plug and the plastic plug clockwise.(Figure 6)
INSTRUCTIONS FOR SHORTING CAP )
- Turn off power.
- Unless optional Photocell device (ordered separately) is to be installed, shorting cap should be installed on the back of light. (Figure 7)
- Make sure the installation is complete and secure before turning on the power.
FUNCTION ADJUSTMENTS (255W, 330W MODELS)
- 1. Open the metal plug and plastic plug counterclockwise with a screwdriver (figure 8) , then slide the switch up and down to adjust the power controller, CCT selector for your application. (Figure 9)
- After adjusting the required control function (Figure 10), tighten the metal plug and the plastic plug clockwise (Figure 11).
WIRING INSTALLATION
- Assure power is off during wiring connections, follow wiring diagram Figure 1 and Figure 2.
- Make sure the installation is completed and secure before turning on the power.
CONTACT
- ADDRESS: 6969 W. 73rd Street Bedford Park, IL 60638
- WWW.LITETRONICS.COM
- CustomerService@Litetronics.com or 1-800-860-3392
The information and product specifications contained in these instructions are based upon data believed to be accurate at the time of printing. This information is subject to change without notice and without incurring liability. If you have questions regarding specific product details, please contact us at 800-860-3392 or via email at customerservice@litetronics.com.
To check for an updated version of these instructions, please visit www.litetronics.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>