Harbor Freight Flaring Tool Kit: Pittsburgh Double – Owner’s Manual

The Harbor Freight Tools PITTSBURGH DOUBLE FLARING TOOL KIT Owner’s Manual provides essential information and instructions for the proper assembly, use, and maintenance of the flaring tool kit. It is important to read the entire manual, including the safety information section before setting up or using the product. The manual emphasizes the importance of wearing safety goggles and heavy-duty work gloves during assembly and use, keeping the assembly and use area clean and well-lit, and keeping bystanders out of the area during assembly or use. It also warns against using the product when tired or under the influence of drugs or medication, and emphasizes that it is not a toy and should be kept away from children. The manual provides detailed operating instructions for creating a double flared end on Copper, Aluminum, Soft Steel, and Brass tubing, and includes a parts list and diagram. The manual also includes a Limited 90 Day Warranty, which covers defects in materials and workmanship for 90 days from the date of purchase.

Harbor-Freight-Tools-PITTSBURGH-DOUBLE-FLARING-TOOL-KIT-LOGO

IMPORTANT SAFETY INFORMATION

Assembly Precautions

1.  Assemble and use only according to these instructions. Improper assembly or use can create hazards.
2.  Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly and use.
3.  Keep assembly and use area clean and well lit.
4.  Keep bystanders out of the area during assembly or use.
5.  Do not assemble or use when tired or when under the influence of drugs or medication.
6.  This product is not a toy. Do not allow children to play with or near this item.
7.  Use for intended purpose(s) only.
8.  Inspect before use; do not use if parts are damaged.
9.  Maintain product labels and nameplates. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.
10.  The quality of flares produced by this tool is largely dependent on the quality and preparation of the workpiece and also the care of the user.
11.  Reposition Flaring Cone over tubing and screw the Yoke down again on the end of the tube until the tubing folds back on itself, forming a 45 degree double flare.

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product.

1.  This tool is used to create a double flared end on Copper, Aluminum, Soft Steel and Brass tubing.
2.  You may flare tubing from 3/16″ to 1/2″ in diameter.
3.  Straighten tubing as much as possible, and then be sure to make a clean cut straight across the tube to avoid a crooked flare. Deburr inner and outer edges. The tube cannot be crushed.
4.  Back off the Flaring Cone and remove the pivoting wing nut. Slide Yoke over Flaring Bar.
5.  Loosen the two wing nuts and insert the prepared tubing into the proper-size hole in the Flaring Bar. The end of the tube must extend above the top of the bar as much as the height of the Adapter Shoulder. For the two smallest Adapters, extend the tube as far as the shoulder on the largest adapter.
6.  After setting the tubing height, tighten the Flaring Bar on the tube by tightening the two wing nuts.
7.  Lightly oil the appropriate sized Adapter and insert it into the end of the tube, button end down.
8.  Position the Flaring Cone over the Adapter.
9.  Turn the Handle of the Yoke driving the
10. Adapter into the end of the tube. The tube
11.  Reposition Flaring Cone over tubing and screw the Yoke down again on the end of the tube until the tubing folds back on itself, forming a 45 degree double flare.
12. Loosen the Yoke, and the wing nuts. Remove the Yoke and Flaring Bar from the tube.
13.  Clean and lightly lubricate the tool, and store it out of reach of children.

Maintenance and Servicing

1.  Before each use, inspect general condition of tool. Check for misalignment or binding of moving parts, cracked or broken parts, and any other condition that may affect its safe operation. Do not use damaged equipment.
2.  After use, clean external surfaces. Then dry and lubricate all moving parts. Do not use solvents.
3.  When storing, keep Flaring Tool and its accessories in its Carrying Case and store in a clean, dry, safe location.
4.  CAUTION! All maintenance, service, and repairs not mentioned in this manual must only be performed by a qualified service technician.

Parts List and Diagram

Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Specify UPC 193175443113 when ordering parts.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials
and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion
may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Specifications

Product Name

|

Harbor Freight Flaring Tool Kit: Pittsburgh Double

---|---

Manufacturer

|

Harbor Freight Tools Co.

Intended Use

|

To create a double flared end on Copper, Aluminum, Soft Steel, and Brass tubing

Tubing Diameter

|

3/16″ to 1/2″

Assembly Precautions

|

• Assemble and use only according to instructions
• Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly and use
• Keep assembly and use area clean and well-lit
• Keep bystanders out of the area during assembly or use
• Do not assemble or use when tired or when under the influence of drugs or medication
• Not a toy; keep away from children
• Use for intended purpose(s) only
• Inspect before use; do not use if parts are damaged
• Maintain product labels and nameplates

Maintenance and Servicing

|

• Inspect general condition of tool before each use
• Check for misalignment or binding of moving parts, cracked or broken parts, and any other condition that may affect its safe operation
• Do not use damaged equipment
• Clean external surfaces after use
• Dry and lubricate all moving parts after use
• Do not use solvents
• Store in a clean, dry, safe location

Parts List

|

• Flaring Bar
• Clamp Bar
• Yoke
• Bar Screw (2)
• Pin (2)
• Wing Nut (2)
• T-Handle
• Flaring Cone
• Yoke Screw
• Retaining Ring
• Steel Ball
• Flat Washer (2)
• Adapter, 5/16″ M8
• Adapter, 3/8″
• Adapter, 1/2″
• Adapter, 3/16″ M4.75
• Adapter, 1/4″
• Carrying Case (not shown)

Warranty

|

Limited 90 Day Warranty covering defects in materials and workmanship

FAQ’s

What is the Harbor Freight Flaring Tool Kit used for?

The Harbor Freight Flaring Tool Kit is used to create a double flared end on Copper, Aluminum, Soft Steel, and Brass tubing.

What safety precautions should be taken when using the Harbor Freight Flaring Tool Kit?

Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly and use, keep the assembly and use area clean and well lit, keep bystanders out of the area during assembly or use, do not assemble or use when tired or under the influence of drugs or medication, and keep the product away from children.

What size tubing can be flared using the Harbor Freight Flaring Tool Kit?

Tubing from 3/16″ to 1/2″ in diameter can be flared using the Harbor Freight Flaring Tool Kit.

How should the tubing be prepared before using the Harbor Freight Flaring Tool Kit?

Straighten tubing as much as possible, and then make a clean cut straight across the tube to avoid a crooked flare. Deburr inner and outer edges. The tube cannot be crushed.

How do you create a double flared end using the Harbor Freight Flaring Tool Kit?

After setting the tubing height, tighten the Flaring Bar on the tube by tightening the two wing nuts. Lightly oil the appropriate sized Adapter and insert it into the end of the tube, button end down. Position the Flaring Cone over the Adapter. Turn the Handle of the Yoke driving the Adapter into the end of the tube. Reposition Flaring Cone over tubing and screw the Yoke down again on the end of the tube until the tubing folds back on itself, forming a 45 degree double flare.

How should I maintain and service my Harbor Freight Flaring Tool Kit?

Before each use, inspect general condition of tool. Check for misalignment or binding of moving parts, cracked or broken parts, and any other condition that may affect its safe operation. Do not use damaged equipment. After use, clean external surfaces. Then dry and lubricate all moving parts. Do not use solvents. When storing, keep Flaring Tool and its accessories in its Carrying Case and store in a clean, dry, safe location.

What is covered under the Limited 90 Day Warranty?

The Limited 90 Day Warranty covers defects in materials and workmanship for 90 days from the date of purchase.

What is not covered under the Limited 90 Day Warranty?

The Limited 90 Day Warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.

How do I take advantage of the Limited 90 Day Warranty?

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>