Harbor Freight Tools 58836 Doyle Portable Chain Vise Owner’s Manual

Harbor Freight Tools 58836 Doyle Portable Chain Vise

Specifications:

• Pipe Capacity: 1/8 – 6 inches

Product Information:

The Portable Chain Vise is a versatile tool designed for holding and bending pipes efficiently. It features various functions including a Tool Holder, Pipe Bender, Jack Screw, Handle Pipe Jaws, Leg Chain, Pipe Chain, and Tool Tray.

Assembly Instructions:

1. Attach Tray Support (3) to Tool Tray (12) with a Tray Pin (15).
2. Slide Clip (18) into ring groove of the Tray Pin and clamp with pliers.
3. Attach Front Legs (22) to the opposite end of the Tool Tray with a Tray Pin (15) and Clip (18).
4. Secure legs to the Base with Shoulder Bolt (26), Washer (28), and Nut (25).
5. Install the Rear Leg (21) by sliding it through the Tray Support Sleeve and into the Base Assembly.

Product Usage Instructions

Before Use:

1. Turn Pipe Stand right-side-up and extend legs fully.
2. Slide the Tray Support Sleeve up all the way and tighten Set Screw (27).

Note: When handling larger pipes, the Jack Screw can be used to support a stabilizing pipe from a ceiling I-beam. Use on a level, concrete floor with exposed steel I-beams overhead. Position the pipe stand directly below.

FAQ:

• Q: What should I do if parts are missing or broken upon unpacking?
  A: If any parts are missing or broken, please call 1-888-866-5797 as soon as possible for assistance.

• Q: How should I maintain the product for optimal safety?
  A: Inspect the product before every use, do not use if parts are loose or damaged, and maintain product labels and nameplates for important safety information.

Save This Manual
Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.

Visit our website at: http://www.harborfreight.com
Email our technical support at: productsupport@harborfreight.com

When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible.
Copyright© 2022 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.
Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL.

Specifications

• Pipe Capacity 1/8″ – 6″

Important Safety Information

1. Unfold stand completely and secure stand firmly before attaching pipe. Provide additional support for stand if attaching larger pipes.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during use.
3. Keep work area clean and well lit.
4. Keep bystanders out of the area during use.
5. Do not use when tired or when under the influence of alcohol, drugs or medication.
6. This product is not a toy. Do not allow children to play with or near this item.
7. Use as intended only.
8. Inspect before every use; do not use if parts are loose or damaged.
9. Maintain product labels and nameplates. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.
10. Damage could occur to your vise and/or workpiece if you overtighten the Handle

SAVE THESE INSTRUCTIONS.

Functions

For technical questions, please call 1-888-866-5797.

Assembly Instructions

1. Attach Tray Support (3) to Tool Tray (12) with a Tray Pin (15).
2. Slide Clip (18) into ring groove of the Tray Pin, and clamp with pliers as shown
3. Attach Front Legs (22) to the opposite end of the Tool Tray with a Tray Pin (15) and Clip (18).
4. Turn the Base (13) upside-down and set on a flat, hard surface. Install the Front Leg posts into the two leg openings on the Jaw (2) side of the Base
5. Secure legs to the Base with Shoulder Bolt (26), Washer (28), and Nut (25).
6. Install the Rear Leg (21) by sliding it through the Tray Support Sleeve and into the Base Assembly (follow step 5 to bolt leg in).

For technical questions, please call 1-888-866-5797.

Before Use

1. Turn Pipe Stand right-side-up and extend legs fully.
2. Slide the Tray Support Sleeve up all the way and tighten Set Screw (27).
3. Push down on Tool Tray until it snaps into place.

Jack Screw

Note : When handling larger pipes, the Jack Screw can be used to support a 1″ stabilizing pipe from a ceiling I-beam. Use on a level, concrete floor with exposed steel I-beams overhead.

1. Position the pipe stand directly below an exposed steel I-beam with a flat mating surface (I-beam flange).
2. Insert a piece of 1″ stabilizing pipe between the I-beam and the Jack Screw on the Pipe Stand
3. Tighten the Jack Screw until stabilizing pipe is applying firm pressure on pipe stand against floor.
4. Test Pipe Stand stability before use.
   Note : Use additional support stands for long lengths of pipe.

Operating Instructions

1. Place workpiece into Jaws.

2. Wrap Chain over workpiece and connect to Jaw (underneath pipe).
   CAUTION! Keep fingers away from Jaws while tightening Chain.

3. Turn Handle clockwise to tighten Jaws against workpiece until it is held securely. Do not overtighten.

4. Turn Handle counterclockwise to open Jaws.

Maintenance

1. Inspect Chain and Jaw for wear or damage before each use. Replace as necessary.
2. Keep moving parts lubricated. Wipe off excess lubricant on Handle and Jaws.
3. Keep Jaws clean. Remove Jaws for cleaning by removing Screws.
4. Periodically, check and tighten mounting hardware.

PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Record Serial Number Here:
Note : If product has no serial number, record month and year of purchase instead.
Note : Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Specify UPC 193175447630 when ordering

Parts List and Diagram

Part| Description| Qty|  | Part| Description| Qty
---|---|---|---|---|---|---
1| Wear Plate| 1| 15| Tray Pin| 3
2| Jaw| 1| 16| Roll Pin| 1
3| Tray Support| 1| 17| Handle| 1
4| Screw| 2| 18| Clip| 3
5| Screw| 2| 19| Friction Ring| 1
6| Nut Locking Pin| 1| 20| Roll| 1
7| Spring Washer| 2| 21| Rear Leg| 1
8| Spacer| 2| 22| Front Leg| 2
9| Leg Chain| 1| 23| Chain Screw| 1
10| Chain| 1| 24| Foot| 3
11| Jack Screw| 1| 25| Nut| 3
12| Tool Tray| 1| 26| Shoulder Bolt| 3
13| Base| 1| 27| Set Screw| 1
14| Swivel Nut| 1| 28| Washer| 3

Diagram

Warranty

Limited 90 Day Warranty

• Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS
• EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
• To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
• This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

26677 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>