Harbor Freight Tools 60570 Bigfoot Panel Wagon Owner’s Manual

BIGFOOT PANEL
WAGON

Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken,  please call 1-888-866-5797 as soon as possible. © Copyright 2022 by Harbor Freight Tools®
. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.
WARNING Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Specifications

IMPORTANT SAFETY INFORMATION

WARNING

Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in serious injury.
Save all warnings and instructions for future reference.

1. AGES 5 AND UP ONLY.
   Do not allow younger children to use.

2. WEAR PROPER SAFETY HELMET AND COMPLETE SAFETY GEAR WHEN RIDING.
   Responsible adult must supervise during use.
   Use as intended only.
   Rider must stay seated at all times during use.
   Do not allow more than one child to play with tricycle at once.

3.  Do not use in unstable or dangerous area.
   Tipping over can cause injury.
   Do not use in areas where vehicles may be present, such as parking areas, driveways, or roads.

4.  Wear ANSI-approved safety goggles and work gloves during assembly.

5.  Read manual before assembly and/or use.

6. Do not exceed 330 lb. capacity.

7.  Inspect before every use; do not use if parts loose or damaged. Check and tighten hardware periodically.

8.  Assemble completely according to instructions before allowing a child to play with this product.

Assembly

Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on facing page.
Note: Bolts include flat / lock washers and nuts / caps. Do not overtighten hardware.

1. Place the Tray (A) upside down on saw horses or other sturdy supports with the bottom facing upwards.

2. Use two 1/2″ Bolts (K) to secure the Rear Axle Assembly (H) to the holes located on the rear of the Tray (A). Insert the Bolts through the Tray and then the Rear Axle Assembly. Secure it in place with the Washers and Cap Nuts (K) on the Tray’s underside.

3.  Slide each Rear Axle Brace (I) over each end of the Rear Axle until they sit firmly next to the bracket of the Rear Axle Assembly (H). Align the  end of the Braces with the holes in the Tray (A).Insert two 1/2″ Bolts (K) through the Tray and then the Braces. Secure them in place with the Washers and Nuts on the Tray’s underside.

4. Place a Steering Washer (M) into the Turntable (D), and into the Steering Assembly (J). Attach the Turntable (D) to Steering Assembly (J) using 1-1/8″ Bolt with a Hole (K). Slide Bolt through underside of the Steering Assembly and into the Turntable. Secure it with the 7/8″ Washer, Large Lock Washer, and nut (K). Leave the nut loose on the Bolt. Insert the Cotter Pin (K) through the Bolt hole and spread it open.

5. Attach the Steering Assembly (J) / Turntable (D) assembly to the Tray (A) with the four 1/2″ Bolts (K)  inserted through the Tray and then the Turntable.

6. Slide a Wheel (C) onto each axle end with the Air Valve facing out. Slide one 1-1/4″ Axle Washer (K) onto each axle next to each Wheel.

7. Place an Axle Cap (K) on each Axle end.

8. Insert the Handle (B) end with hole into the Steering Assembly (J). Insert the 2-5/8″ Bolt (K) through the Steering Assembly, Handle, and back through the other side of the Steering Assembly, and secure in place with a Small Washer and Nut Cap.

9. Turn the Wagon over so the Tray (A) faces up. Assemble one (1) of the Long Side Panels (E) to the wagon with the three 1-3/4″ Bolts (K) going through the Tray from the inside first and then each vertical slat. Secure them in place with Washers and Nut Caps.
   Note: The Short Front Panel (G) is the one with a downward curved front slat.

10.  Assemble the Short Rear Panel (F) to the Tray (A) with two 1-3/4″ Bolts (K) going through the Tray from the inside first and then each vertical slat. Secure them in place with Washers and Nut Caps.

11.  Assemble the second Long Side Panel (E) as in step 9.

12.  Assemble the Short Front Panel (G) with two 1-3/4″ Bolts (K) going through the Tray from the inside first and then each vertical slat. Secure them in place with Washers and Nut Caps.

Parts List and Diagram

*Bolts include flat / lock washers and nuts / caps.

Operation

The Wagon has a long handle mounted at the front. Use the handle to pull the wagon to the destination, as well as transport loads to and from destinations.
Turning the Handle (B) will cause the front wheels on the wagon to turn. Turn the Handle in the direction for the wagon to follow. The Handle can be raised for steering from inside the wagon, or lowered so that the wagon can be pulled from in front.

Maintenance

1. Periodically check tire inflation (maximum tire inflation is: 30 PSI for rear tires, 35 PSI for front tires).
2. Periodically lubricate wheel axles.
3. Check and tighten hardware periodically.

PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts. Specify UPC 193175505767 when ordering parts.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date  of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

26677 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797For technical questions, please call 1-888-866-5797.
Visit our website at: http://www.harborfreight.com
Email our technical support at: productsupport@harborfreight.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>