comsol WCSM10 10W Wireless Fast Charging Stand User Manual

: June 5, 2024
: comsol

Table of Contents

Compatibility
Features
Wireless Charger Operation
Specifications
Important Safety Instructions
Documents / Resources

comsol WCSM10 10W Wireless Fast Charging Stand

Compatibility

*Compatible with Qi-enabled devices including.**

iPhone X
iPhone 8
iPhone 8 Plus
Samsung S9/S9+
Samsung S8/S8+
Samsung S7/S7 Edge
Samsung Note 8
Samsung Note 5
Sony Xperia XZ2
Nokia 8 Sirocco
LG G7 ThinQ
LG V30+

Features

Two charging coils enable large wireless coverage to allow charging in portrait or landscape mode
Supports 10W wireless fast charging for compatible devices such as Samsung Galaxy S9, S9+, S8, S8+, Note 8, S7 & S7 Edge#
Supports 7.5W Apple wireless fast charging for iPhone X/8/8 Plus#
Supports 5W standard wireless charging for all Qi enabled devices
No need to remove your protective case. Works with most cases up to 3mm thick
LED indicator to show charging status
Smart IC enables energy saving mode when device is fully charged
Full safety protection for your devices with Qi certified temperature control, strict voltage regulation & short circuit protection
Includes 1.5m micro USB cable to connect charging stand to USB wall charger (USB wall charger not included)
Check with device manufacturer for Qi wireless compatibility # When connected to a Quick Charge 2.0 or 3.0 wall charger (not included)

Wireless Charger Operation

Using the included micro USB cable, connect the wireless charging stand to a USB wall charger (USB wall charger not included)
It is recommended to use original or reputable 3rd party branded USB wall chargers. For faster charging times it is recommended to use a USB wall charger with a minimum of 2A output
When connected to the USB charger, the red LED will be on for 3 seconds to indicate the charging stand is powered on and in stand-by mode
Place your Qi enabled wireless phone on the charging stand and your phone should start charging automatically
The LED will flash green to indicate charging
If your phone does not start charging, move your phone until the correct position is found and your phone starts charging
When your phone is fully charged, the Smart IC enables energy saving trickle charge mode

Please Note
To achieve 10W fast charging for Android devices or 7.5W fast charging for Apple devices, the charging stand needs to be connected to a Quick Charge 2.0 or 3.0 wall charger (not included)

Specifications

Wireless Standard: WPC/Qi (v1.2.3)
Quantity of Wireless Charging Coils: Two Coils
Input: DC 5V 2A or DC 9V 2A
Output: 5W / 7.5W / 10W (Max)
Working Frequency: 110 to 205KHz
Charging Distance: 3 to 8mm
Charging Efficiency: >72%
Dimensions: 125 x 70 x 98mm
Weight: 178g

Important Safety Instructions

Only use original or reputable third party chargers and cables
Do not get wet to avoid causing short circuit damage and leakage
Do not use in extreme hot, humid or corrosive environments to avoid short circuit damage and leakage
Do not place too close to magnetic strip or chip ID card to avoid magnetic failure
Do not place within 20cm of implantable medical devices (pacemaker, cochlear implant etc.) to avoid potential interference
Do not clean with harmful chemicals or detergents
Misuse, dropping or excessive force may cause damage to the charging stand

Please Note: When wirelessly charging a device, the wireless charger and your device may feel warm. This is a normal operating condition and should not be cause for concern.

iPhone is a trademark of Apple inc., registered in the U.S. and other countries. The `Qi’ Symbol is a trademark of the Wireless Power Consortium. Android is a trademark of Google Inc.

Made in China

www.mycomsol.com.au

Documents / Resources

| comsol WCSM10 10W Wireless Fast Charging Stand [pdf] User Manual
WCSM10, 10W Wireless Fast Charging Stand, WCSM10 10W Wireless Fast Charging Stand
---|---