comsol WCTA10 Apple 3-in-1 Wireless Charging Dock User Manual

comsol WCTA10 Apple 3-in-1 Wireless Charging Dock

Compatibility

Compatible with Qi-enabled devices* including

• iPhone 11 Pro/11
• iPhone XS/XS Max/XR
• iPhone X/8/8 Plus
• Samsung Galaxy Fold
• Samsung S10/S9/S8
• Samsung Note 10/9/8/5
• Huawei P30 Pro
• Huawei Mate 30/20 Pro
• Google Pixel 3/3 XL
• Sony Xperia XZ2
• LG G7 ThinQ
• LG V30+

Features

• Can charge a wireless iPhone and wireless Airpods or two wireless phones

• Requires Apple Watch magnetic charging cable to insert into dock (not included)

• Supports 7.5W Apple wireless fast charging for iPhone 8 or later

• Supports 10W wireless fast charging for compatible devices such as Samsung Galaxy Series and more

• Supports 5W standard wireless charging for all Qi enabled devices

• No need to remove your protective case. Works with most cases up to 3mm thick

• LED indicator to show charging status

• Smart IC enables energy saving mode when device is fully charged

• Full safety protection for your devices with Qi certified temperature control, strict voltage regulation & short circuit protection

• Includes AC wall charger and 1.5m USB-A to USB-C cable

• Check with device manufacturer for Qi wireless compatibility

Wireless Charger Operation

• Untwist the black cover of the Watch charger housing
• Using your exisiting Apple Watch magnetic charging cable (not included), insert into the holder and wrap the cable around the cylinder and plug into the USB-A port on the back of the dock
• Twist the black cover back over the watch magnetic charger
• The red LED will be on for 3 seconds to indicate the charging pad is powered on and in stand-by mode
• Place your wireless phone on either charging pad and your phone should start charging automatically
• If your phone does not not start charging, move your phone until the correct position is found and your phone starts charging
• Place your wireless charging Airpods on either charging pad
• Place your Apple watch on the Apple magnetic watch charger
• The LED will flash green to indicate charging
• When your phone is fully charged, the Smart IC enables energy saving trickle charge mode

Please Note: When wirelessly charging a device, the wireless charger and your device may feel warm. This is a normal operating condition and should not be cause for concern.

Specifications

• Wireless Standard: WPC/Qi (v1.2.4)
• Quantity of Wireless Charging Coils: One Coil per Pad
• Input: QC 3.0 DC 9V 2A
• Output: 10W / 7.5W / 5W / 3W for charging pads
• Output: DC 5V 2A for Apple Watch
• Working Frequency: 110 to 205KHz
• Charging Distance: 3 to 8mm
• Charging Efficiency: >72%
• Dimensions: 228 x 75 x 76mm

Important Safety Instructions

• Only use original or reputable third party chargers and cables
• Do not get wet to avoid causing short circuit damage and leakage
• Do not use in extreme hot, humid or corrosive environments to avoid short circuit damage and leakage
• Do not place too close to magnetic strip or chip ID card to avoid magnetic failure
• Do not place within 20cm of implantable medical devices (pacemaker, cochlear implant etc.) to avoid potential interference
• Do not clean with harmful chemicals or detergents
• Misuse, dropping or excessive force may cause damage to the charging dock

iPhone is a trademark of Apple inc., registered in the U.S. and other countries.
The ‘Qi’ Symbol is a trademark of the Wireless Power Consortium. Android is a trademark of Google Inc.
www.mycomsol.com.au

References

• Comsol Retail

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>