comsol WFC15 15W Fast Wireless Charging Pad User Manual
- June 5, 2024
- comsol
Table of Contents
comsol WFC15 15W Fast Wireless Charging Pad
Qi Certified
The certificationprogram ensures this charger has passed rigorous tests to guarantee safety, compatibility and energy efficiency.
Compatibility
Compatible with Qi-enabled devices* including
- iPhone X
- iPhone 8
- iPhone 8 Plus
- Samsung S9/S9+
- Samsung S8/S8+
- Samsung S7/S7 Edge
- Samsung Note 8
- Samsung Note 5
- Sony Xperia XZ2
- Nokia 8 Sirocco
- LG G7 ThinQ
- LG V30+
Features
- 360˚ rotation to change from flat surface to angled surface
- Supports 7.5W Apple wireless fast charging for iPhone X/8/8 Plus
- Supports 10W wireless fast charging for compatible devices such as Samsung Galaxy S9, S9+, S8, S8+, Note 8, S7 & S7 Edge
- Supports 15W wireless fast charging to future proof your wireless charging needs
- Supports 5W standard wireless charging for all Qi enabled devices
- No need to remove your protective case. Works with most cases up to 3mm thick
- LED indicator to show charging status
- Smart IC enables energy saving mode when device is fully charged
- Full safety protection for your devices with Qi certified temperature control, strict voltage regulation & short circuit protection
- Includes certified Quick Charge 3.0 USB wall charger and 1.5m micro USB cable
Check with device manufacturer for Qi wireless compatibility
Wireless Charger Operation
- Using the included micro USB cable, connect the wireless pad to the included Quick Charge 3.0 USB wall charger
- The red LED will be on for 3 seconds to indicate the charging pad is powered on and in stand-by mode
- Place your Qi enabled wireless phone on the charging pad and your phone should start charging automatically
- The LED will flash green to indicate charging
- If your phone does not start charging, move your phone until the correct position is found and your phone starts charging
- When your phone is fully charged, the Smart IC enables energy saving trickle charge mode
Please Note
To achieve 7.5W fast charging for Apple devices or 10W fast charging for
Android devices, the charging pad needs to be connected to the included Quick
Charge 3.0 USB wall charger or equivalent.
Specifications
- Wireless Standard: WPC/Qi (v1.2.3)
- Quantity of Wireless Charging Coils: One Coil
- Input: DC 5V 2A or DC 9V 2A or DC 12V 2A
- Output: 5W / 7.5W / 10W / 15W (Max)
- Working Frequency: 110 to 205KHz
- Charging Distance: 3 to 8mm
- Charging Efficiency: >72%
- Dimensions: 77 x 77 x 26.5mm
- Weight: 100g
Important Safety Instructions
- Only use original or reputable third party chargers and cables
- Do not get wet to avoid causing short circuit damage and leakage
- Do not use in extreme hot, humid or corrosive environments to avoid short circuit damage and leakage
- Do not place too close to magnetic strip or chip ID card to avoid magnetic failure
- Do not place within 20cm of implantable medical devices (pacemaker, cochlear implant etc.) to avoid potential interference
- Do not clean with harmful chemicals or detergents
- Misuse, dropping or excessive force may cause damage to the charging pad
Please Note: When wirelessly charging a device, the wirelesscharger and
your device may feel warm. This is a normal operating condition and should
not be cause for concern.
iPhone is a trademark of Apple inc., registered in the U.S. and other
countries. The ‘Qi’ Symbol is a trademark of the Wireless Power Consortium.
Android is a trademark of Google Inc.
www.mycomsol.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>