milwaukee M12 CD Battrey Compact Drilling Machine User Guide

: June 5, 2024
: Milwaukee

Table of Contents

Milwaukee M12 CD Battery Compact Drilling Machine
TECHNICAL DATA
BATTERIES
MAINTENANCE
Assembly
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Milwaukee M12 CD Battery Compact Drilling Machine

TECHNICAL DATA

Drilling capacity in steel

| ****

6.35 mm

---|---
Drilling capacity in wood| 25 mm
Wood screws (without pre-drilling)| 8 mm
No-load speed, 1st gear| 0-450 min-1
No-load speed, 2nd gear| 0-1700 min-1
Torque max (Li-Ion Battery 1.5 Ah) | 37 Nm
Torque max (Li-Ion Battery 3.0 Ah) | 44 Nm
Battery voltage| 12 V
Tool reception| 1/4” (6.35 mm)
Weight according EPTA-Procedure 01/2003 (1.5 Ah)| 1.16 kg
Noise/vibration information|
Measured values were determined according to EN 60745.|
Typically, the A-weighted noise levels of the tool are:|
Sound pressure level (Uncertainty K = 3 dB(A))| 74 dB (A)
Sound power level (Uncertainty K = 3 dB(A))| 85 dB (A)
Wear ear protection!|
Total vibration values (vector sum in the three axes) determined according to EN 60745:|
Vibration emission value ah Drilling into metal| ****

1.27 m/s2

Uncertainty K| 1.5 m/s2
Screwdriving| 1.27 m/s2
Uncertainty K| 1.5 m/s2

**** The possible causes may be:

SCREWDRIVER SAFETY WARNINGS
Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear defenders The dust produced when using this tool may be harmful to health. Do not inhale the dust. Wear a suitable dust protection mask. Do not machine any materials that present a danger to health (e.g., asbestos). Switch the device off immediately if the insertion tool stalls! Do not switch the device on again while the insertion tool is stalled, as doing so could trigger a sudden recoil with a high reactive force. Determine why the insertion tool stalled and rectify this, paying heed to the safety instructions.

it is tilted in the workpiece to be machined
it has pierced through the material to be machined
the power tool is overloaded

Do not reach into the machine while it is running. The insertion tool may become hot during use. WARNING! Danger of burns

when changing tools
when setting the device down

Chips and splinters must not be removed while the machine is running. When working in walls ceiling, or fl oor, take care to avoid electric cables and gas or waterpipes. Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage. Remove the battery pack before starting any work on the machine. Do not dispose of used battery packs in the household refuse or by burning them. Milwaukee Distributors offer to retrieve old batteries to protect our environment. Do not store the battery pack together with metal objects (short circuit risk). Use only System M 12 chargers for charging System M 12 battery packs. Do not use battery packs from other systems. Never break open battery packs and chargers and store only in dry rooms. Keep dry at all times. Battery acid may leak from damaged batteries under extreme load or extreme temperatures. In case of contact with battery acid wash it off immediately with soap and water. In case of eye contact rinse thoroughly for at least 10 minutes and immediately seek medical attention.

BATTERIES

Battery packs that have not been used for some time should be recharged before use. Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine (risk of overheating). The contacts of chargers and battery packs must be kept clean. For an optimum life-time, the battery packs have to be fully charged, after used. To obtain the longest possible battery life remove the battery pack from the charger once it is fully charged. For battery pack storage longer than 30 days: Store the battery pack where the temperature is below 27°C and away from moisture Store the battery packs in a 30% – 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situations that cause high current draw, the tool will stop for about 2 seconds and then the tool will turn OFF. To reset, release the trigger. Under extreme circumstances, the internal temperature of the battery could become to high. If this happens, the battery will shut down.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. Transportation of those batteries has to be done in accordance with local, national and international provisions and regulations. The user can transport the batteries by road without further requirements. ï Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusive to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.
When transporting batteries:
Ensure that battery contact terminals are protected and insulated to prevent short circuit. Ensure that battery pack is secured against movement within packaging. ï Do not transport batteries that are cracked or leak. Check with the forwarding company for further advice

MAINTENANCE

Use only Milwaukee accessories and spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents. If needed, an exploded view of the tool can be ordered. Please state the serial no. as well as the machine type printed on the label and order the drawing at your local service agents.