milwaukee M12 BD Cordless Drill Driver Instruction Manual
- October 27, 2023
- Milwaukee
Table of Contents
Milwaukee M12 BD Cordless Drill Driver
Figures
| Remove the battery pack before starting any work on the machine.
---|---
| Remove the battery pack before starting any work on the machine.
---|---
TECHNICAL DATA
CORDLESS DRILL DRIVER
|
M12 BD
---|---
Production code| 4419 01 02 000001-999999
Drilling capacity in steel| 10 mm
Drilling capacity in wood| 20 mm
Wood screws (without pre-drilling)| 6 mm
No-load speed 1st gear| 0-400 min-1
No-load speed 2nd gear| 0-1500 min-1
Torque max (Li-Ion Battery 2.0 Ah) | 30 Nm
Torque max (Li-Ion Battery 4.0 Ah) | 38 Nm
Battery voltage| 12 V
Tool reception| 1/4″ (6,35 mm)
Weight according EPTA-Procedure 01/2003 (2.0 Ah)| 1,02 kg
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))| 85,0 dB (A)
Sound power level (Uncertainty K=3dB(A))| 96,0 dB (A)
Wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value ah
Drilling into metal| 1,5 m/ S2
Uncertainty K=| 1,5 m/ S2
Screwing| 0,4 m/ S2
Uncertainty K=| 1,5 m/ S2
***** Measured according to Milwaukee Standard N 877318
WARNING
The vibration emission level given in this information sheet has been measured
in accordance with a standardized test given in EN 60745 and may be used to
compare one tool with another. It may be used for a preliminary assessment of
exposure.
The declared vibration emission level represents the main applications of the
tool. However if the tool is used for different applications, with different
accessories or poorly maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total working period. An
estimation of the level of exposure to vibration should also take into account
the times when the tool is switched off or when it is running but not actually
doing the job. This may significantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the operator from the effects
of vibration such as: maintain the tool and the accessories, keep the hands
warm, organization of work patterns.
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious injury. Save all warnings and instructions for future reference.
DRILL SAFETY WARNINGS
Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a „live“ wire may make exposed metal parts of the power tool „live“ and could give the operator an electric shock.
SCREWDRIVER SAFETY WARNINGS
Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale
the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch
the device on again while the insertion tool is stalled, as doing so could
trigger a sudden recoil with a high reactive force. Determine why the
insertion tool stalled and rectify this, paying heed to the safety
instructions
The possible causes may be:
- it is tilted in the workpiece to be machined
- it has pierced through the material to be machined
- the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
- when changing tools
- when setting the device down
Chips and splinters must not be removed while the machine is running. When working in walls ceiling, or floor, take care to avoid electric cables and gas or waterpipes. Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning
them. Milwaukee Distributors offer to retrieve old batteries to protect our
environment. Do not store the battery pack together with metal objects (short
circuit risk).
Use only System M 12 chargers for charging System M 12 battery packs. Do not
use battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep
dry at all times.
Battery acid may leak from damaged batteries under extreme load or extreme
temperatures. In case of contact with battery acid wash it off immediately
with soap and water. In case of eye contact rinse thoroughly for at least 10
minutes and immediately seek medical attention.
SPECIFIED CONDITIONS OF USE
The battery drill/screwdriver may be used for drilling and screw driving for independent use away from mains supply. Do not use this product in any other way as stated for normal use.
BATTERIES
Battery packs which have not been used for some time should be recharged
before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery
pack. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged, after
used.
To obtain the longest possible battery life remove the battery pack from the
charger once it is fully charged.
For battery pack storage longer than 30 days: Store the battery pack where the
temperature is below 27°C and away from moisture Store the battery packs in a
30% – 50% charged condition Every six months of storage, charge the pack as
normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situations that
cause high current draw, the tool will vibrate for about 5 seconds, the fuel
gauge will flash and then the tool will turn OFF. To reset, release the
trigger.
Under extreme circumstances, the internal temperature of the battery pack
could raise too much. If this happens, the fuel gauge will flash until the
battery pack cooled down. After the lights go off, the work may continue.
MAINTENANCE
Use only Milwaukee accessories and spare parts. Should components need to be
replaced which have not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
machine type printed as well as the six-digit No. on the label and order the
drawing at your local service agents or directly at: Techtronic Industries
GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
| CAUTION! WARNING! DANGER!
---|---
| Remove the battery pack before starting any work on the machine.
| Please
read the instructions carefully before starting the machine.
| Accessory –
Not included in standard equipment, available as an accessory.
| Do not dispose of electric tools together with household waste material.
Electric tools and electronic equipment that have reached the end of their
life must be collected separately and returned to an environmentally
compatible recycling facility. Check with your local authority or retailer for
recycling advice and collection point.
| European Conformity Mark
| EurAsian Conformity Mark.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described under “Technical Data” fulfills all the relevant regulations and the directives 2011/65/EU (RoHs), 2014/30/ EU, 2006/42/EC, and the following harmonized standards have been used:
EN 60745-1:2009 + A11:2010
EN 60745-2-1:2010
EN 60745-2-2:2010
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 50581:2012
Winnenden, 2016-03-29
Alexander Krug Managing Director
Authorized to compile the technical fi le
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
Documents / Resources
|
milwaukee M12 BD Cordless Drill
Driver
[pdf] Instruction Manual
M12 BD, Cordless Drill Driver, M12 BD Cordless Drill Driver, Drill Driver,
Driver
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>