THE HOME DEPOT 28508 3 Infrared Motion Sensor Instructions

: June 3, 2024
: THE HOME DEPOT

Table of Contents

THE HOME DEPOT 28508 3 Infrared Motion Sensor
INFRARED MOTION SENSOR
SPECIFICATION
FUNCTION
INSTALLATION ADVICE
CONNECTION
CONNECTION-WIRE DIAGRAM
SOME PROBLEMS AND SOLVED WAY
Documents / Resources

THE HOME DEPOT 28508 3 Infrared Motion Sensor

INFRARED MOTION SENSOR

Welcome to use 28508 3 Infrared motion sensor!
The product adopts a good sensitivity detector and integrated circuit. It gathers automatism, convenience, safety, saving energy, and practical functions. It utilizes the infrared energy from humans as a control-signal source and it can start the load at once when one enters the detection field. It can identify day and night automatically. It is easy to install and is used widely.

SPECIFICATION

Power Source: 220-240V/AC Detection Range: 360°
Power Frequency: 50Hz Detection Distance: 12m max(<24°C)
Ambient Light: <3-2000LUX (adjustable) Working
Temperature: -20~+40°C
Time Delay: 10sec±3sec • Working
Humidity: <93%RH
Max. 15min±2min
Power Consumption: approx 0.5W
Rated Load: 1200W
Installation Height: 2.2-4.0m
Max. 300W
Detection Moving Speed: 0.6-1.5m/s

FUNCTION

Can identify day and night: The consumer can adjust the working state in different ambient lights. It can work in the daytime and at night when it is adjusted to the “sun” position (max). It can work in the ambient light less than 3LUX when it is adjusted to the “moon” position (min). As for the adjustment pattern, please refer to the testing pattern.
Time-Delay is added continually: When it receives the second induction signal within the first induction, it will restart to time from the moment.

INSTALLATION ADVICE

As the detector responds to changes in temperature, avoid the following situations:

Avoid pointing the detector towards objects with highly reflective surfaces, such as mirrors, etc.
Avoid mounting the detector near heat sources, such as heating vents, air conditioning units, lights, etc.
Avoid pointing the detector towards objects that may move in the wind, such as curtains, tall plants, etc.

CONNECTION

Warning. The danger of death through electric shock!

Must be installed by a professional electrician.
Disconnect the power source.
Cover or shy any adjacent live components.
Ensure the device cannot be switched on.
Check power supply is disconnected.
Please move the upper cover with an anti-clockwise whirl as per the diagram on the right.
Connect the power and the load according to the connection-wire diagram.
Fix the bottom on the selected position with the inflated screw.
Install back the upper cover on the sensor, then you could switch on the power and test it.

CONNECTION-WIRE DIAGRAM

See the right figure

TEST

Turn the TIME knob anti-clockwise on the minimum (10s). Turn the LUX knob clockwise on the maximum (sun).
Switch on the power; the sensor and its connected lamp will have no signal at the beginning. After Warm-up 30sec, the sensor can start working. If the sensor receives the induction signal, the lamp will turn on. While there is no other induction signal anymore, the load should stop working within 10sec±3sec and the lamp would turn off.
Turn LUX knob clockwise on the minimum (moon). If the ambient light is more than 3LUX, the sensor would not work and the lamp stop working too. If the ambient light is less than 3LUX (darkness), the sensor would work. Under no induction signal condition, the sensor should stop working within 10sec±3sec.

Note: when testing in daylight, please turn the LUX knob to the (SUN) position, otherwise the sensor lamp could not work!

SOME PROBLEMS AND SOLVED WAY

The load does not work:
a. Please check if the connection of the power source and load is correct.
b. Please check if the load is good.
c. Please check if the settings of the working light correspond to ambient light.
The sensitivity is poor:
a. Please check if there is any hindrance in front of the detector to affect it to receive the signals.
b. Please check if the ambient temperature is too high.
c. Please check if the induction signal source is in the detection field.
d. Please check if the installation height corresponds to the height required in the instruction.
e. Please check if the moving orientation is correct.
The sensor can not shut off the load automatically:
a. Please check if there is a continual signal in the detection field.
b. Please check if the time delay is set to the maximum position
c. Please check if the power corresponds to the instruction.

Produced by REV Ritter (China) GmbH 9F, Building A, Hengyuan Plaza
No.1988 Beisanhuan East Rd.
Cixi, Ningbo, China
https://tm.by

Documents / Resources

| THE HOME DEPOT 28508 3 Infrared Motion Sensor [pdf] Instructions
28508 3 Infrared Motion Sensor, 28508 3, Infrared Motion Sensor, Motion Sensor, Sensor
---|---