THE HOME DEPOT GZHSKN0721005 52 Inch Integrated LED Indoor-Outdoor Black Ceiling Fan Instruction Manual

Instruction Manual

GZHSKN0721005 52 Inch Integrated LED Indoor-Outdoor Black Ceiling Fan

Cautions and Warnings

• READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION. SAVE THESE INSTRUCTIONS.
• Use only Exbrite replacement parts.
• To reduce the risk of personal injury, attach the fan directly to the support structure of the building according t o these instructions, and use only the hardware supplied.
• To avoid possible electrical shock , before installing your fan , disconnect the power by turning off the circuit breakers to the out let box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as atag , to the service panel.
• All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician.
• To reduce the risk o f personal injury, do not bend the blade attachment system when installing, balancing, or cleaning the fan . Never insert foreign objects between rotating fan blades.
• To reduce the risk of fire, electrical shock, or motor damage, do not use a solid-state speed control with this fan . Use only Exbrite speed controls

NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible conditions and situations that may occur. It must be  understood that common sense and caution are necessary factors in the installation and operation of this fan.

Parts Inventory

Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet o r Styrofoam to avoid damage t o finish. Check against parts inventory that all parts have been included.

• Downrod and hanging ball

Installation Preparation

To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 2.3m from the floor and 76cm from ; any wall or obstruction.  Be sure the outlet box is securely attached to the building structure and can support the full weight of the fan .

Preparing the Fan Site

Downrod Installation
This fan can be mounted with a downdrod on a normal or vaulted ceiling.
The hanging length can be extended by a longer downdrod.
Installation requires these tools:
Screwdriver, flat-head screwdriver, adjustable pliers or wrench, stepladder, wire cutters, and rated electrical tape.

Installing the Hanger Bracket

Please tighten the bracket in the wood ceiling with tapping screws.

Please drill p8mm hole on the concrete ceiling, and insert the bolt. Align bracket with the hole, then tighten with nut.

Step2: | Assembling and Hanging the Fan

If you wish to extend the hanging length of your fan , you must remove the hanging ball from the 6 inch downrod provided to use with an extended downrod (included) . (If you wish to use the 6 inch downrod, please proceed to instructions below.)
To remove hanging ball, loose set screw on hanging ball and remove pin and clip. Lower hanging ball and remove stop pin. Slide hanging ball off the original downrod A, and  slide it down the longer downrod B ( the top of the downrod should be noted as having a set screw hole; use this hole when setting the set screw). Insert stop pin into top of  extended downrod and raise hanging ball.Be sure stop pin aligns with slots on the inside of the hanging ball, tighten set screw securely. |
Tip: To prepare for threading electrical wires through downrod, apply small piece of electrical tape to the ends of electrical wires-this will keep the wires together when threading them through the downrod.
Loosen yoke set screws and nut at top of motor housing. Remove pin and clip from downrod (if you have not already done so). Slide downrod through canopy.
Tread electrical wires through downrod and pull extra wire slack from the upper end of the downrod.
Place downrod into the motor housing yoke and ew-insert pin and clip that were previously removed. Tighten yoke set screws and nut securely.Lower canopy to motor housing.

Step3: Remote control connection

Canopy Assembly

Raise canopy to hanging bracket, aligning loosened screws in hanging bracket with slotted holes in canopy. Twist canopy to lock . Re-insert screws and secured all screws with screwdriver.
With hanging bracket secured to the outlet box and able to support to fan, you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through  opening in hanging bracket and let hanging ball rest on the hanging bracket. Turn the hanging ball slot until it lines up with the hanging bracket tab.
Tip: Seek the help of another person to hold the stepladder in place and to lift the fan up to you once you are set on the ladder.

Blade Assembly

First of all, please refer to step A in diagram 1. Fix blades on connectors by screws, then refer t o step Bin diagram 1, fix connectors on motor by screws
Time Saver: Washers for blade screws can be set on each blade screw prior to installing blades.
Align blade holes with motor screw holes, Securing tighten all the screws once all the blades are attached. Before securing screws permanently, repeat with remaining blade  arms.
Note: Tighten blade screws twice.

LED Pan Assembly

Unscrew a set screw. Attach the LED pan up to the bottom of the fan by inserting the other two set screw heads into key hole slots, rotate it to place, then secure the previous set screw by aligning screw hole and the hole at the bottom of the fan, tighten the rest two set screw to secure LED pan.
NOTE: While install or remove the LED pan, please keep the insulation pads intact carefully. Turning the set screws over-tightly or fast will damage the insulation pads.

Lamp Shade Assembly

Unscrew a set screw. Attach the LED pan up to the bottom of the fan by inserting the other two set screw heads into key hole slots, rotate it to place, then secure the  previous set screw by aligning screw hole and the hole at the bottom of the fan , tighten the rest two set screw to secure LED pan .
NOTE: While install o r remove the LED pan, please keep the insulation pads in tactcare fully .
Turning the set screws over-tightly or fast will damage the insulation pads.

Decorative Pan Inventory

Restore the cover and the lamp shade back to the LED pan, and secure them with decorative clips and bolt nuts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>