amzchef P-002B Meat Grinder Attachment Instruction Manual
- June 5, 2024
- amzchef
Table of Contents
- PARTS AND FEATURES
- METAL FOOD GRINDER ATTACHMENT SAFETY
- IMPORTANT SAFEGUARDS **FOR USE MEAT GRINDER
- USING THE METAL FOOD GRINDER ATTACHMENT
- TIPS FOR GREAT RESULTS OF MEAT GRINDER
- CARE AND CLEANING FOR MEAT GRINDER
- WARRANTY
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
INSTRUCTION MANUAL
Meat Grinder Attachment
Model No.:P-002B
PLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY RETAIN THIS MANUAL FOR FUTURE REFERENCE
PARTS AND FEATURES
PARTS AND ACCESSORIES
METAL FOOD GRINDER ATTACHMENT SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your
appliance. Always read and obey all safety messages. This is the safety alert
symbol.
** This symbol alerts you to potential hazards that can kill or hurt you
and others.
All safety messages will follow the safety alert symbol and either the word
“DANGER” or “WARNING.” These words mean:
DANGER You can be killed or seriously injured if you don’t immediately
follow instructions.
WARNING You can be killed or seriously injured if you don’t follow
instructions.
**All safety messages will tell you what the potential hazard is, tell you how
to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
IMPORTANT SAFEGUARDS **FOR USE MEAT GRINDER
**
When using electrical appliances, basic safety precautions should always be followed, including the following:
- Read all instructions.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience or knowledge, unless they are closely supervised and instructed concerning use of the appliance by a person responsible for their safety. Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they do not play with the appliance.
- Turn the Slow juicer OFF (and detach the Metal Food Grinder attachment from the Slow juicer) after each use of the attachment and before cleaning. Make sure motor stops completely before disassembling.
- Avoid contacting moving parts. Keep fingers out of the discharge opening.
- The use of attachments not recommended or sold by us may cause fire, electric shock, or injury.
- Never feed food by hand. Always use the food pusher.
- Blades are sharp. Handle carefully.
- Do not use fingers to scrape food away from the discharge disc while the appliance is operating. Cut-type injury may result.
- Also see the Important Safeguards section included in the Slow juicer Use and Care guide.
SAVE THESE INSTRUCTIONS
This product is designed for household use only.
USING THE METAL FOOD GRINDER ATTACHMENT
GUIDE TO GRINDING
USE THESE PARTS | WITH THESE PARTS | SUGGESTED USES |
---|---|---|
Fine grinding plate (3 mm) | Blade | Cooked meats for spreads, hard cheeses |
(e.g.Parmesan), bread crumbs
Medium grinding plate (4.5 mm)| Blade| Raw or cooked meats, meats for sausages
Coarse grinding plate (8 mm)| Blade| Raw meats for burgers and chili,
vegetables for salsas and sauces
Small sausage stuffer tube (9.5 mm)| Sausage stuffer plate| Breakfast sausage,
smaller sausages
Medium sausage stuffer tube (19 mm)| Sausage stuffer plate| Bratwurst, medium
sausages
Large sausage stuffer tube(32mm)| Sausage stuffer plate| Bratwurst,larger
sausages
USING THE METAL FOOD GRINDER ATTACHMENT
ASSEMBLING THE METAL FOOD GRINDER ATTACHMENT
Wash all parts with warm, soapy water and dry thoroughly before use.
| Insert the grind screw into the main housing. Then, place the blade over the
end of the grind screw. The blade should fit entirely inside the housing. If
it doesn’t, pull it off, turn it over, and place it again.
---|---
| Place grinding plate over the blade, matching the notch of the plate with
the tab on the bottom of the main housing.
| Place the collar on the main housing, turning clockwise by hand until
secured but not tightened.
ATTACHING THE METAL FOOD GRINDER ATTACHMENT TO THE SLOW JUICER
| Turn the Slow Juicer off and unplug.
---|---
| Insert the attachment shaft into the hub socket on the main body of juicer.
Rotate the attachment anticlockwise until you hear a “Tick” sound. Rotate
attachment back and forth if necessary.
USING THE METAL FOOD GRINDER ATTACHMENT
GRINDING WITH THE FOOD GRINDER
| Cut food into small strips or pieces sized to fit into the feed tube.
---|---
| WARNING
---|---
Rotating Blade Hazard
Always use food pusher.
Keep fingers out of openings.
Keep away from children.
Failure to do so can result in amputation or cuts.
| Turn on the slow juicer and feed food into
the feed tube using the food pusher.
---|---
USING THE METAL FOOD GRINDER ATTACHMENT
ASSEMBLING THE SAUSAGE STUFFER
| Insert the grind screw into the main housing. Then insert the sausage
stuffer plate over the end of the grind screw, matching the notch of the plate
with the tab on the bottom of the main housing.
---|---
| Insert the desired sausage stuffer tube (large or small) through the collar.
Then, place the collar and tube assembly on the main housing, turning the ring
by hand until secured but not tightened.
USING THE SAUSAGE STUFFER
| Feed meat into the Metal Food Grinder attachment before adding the sausage
stuffer tube. This will eliminate air pockets.
---|---
| Lubricate the sausage stuffer tube and slide one casing over the tube,
leaving about four inches to tie off the end.
| Turn on the slow juicer and slowly push the meat through the grinder. Hold
the casing firmly as it fills. If air bubbles are created during the fill
process, use a pin or needle to pop the bubble.
| Run meat through until 4-6 inches of casing is left unfilled. Turn off the
slow juicer and tie the remaining end of the casing or use a tie string.
NOTE: For segmented-type sausage (e.g., bratwurst), twist casing ends in alternating directions at desired sausage link length.
TIPS FOR GREAT RESULTS OF MEAT GRINDER
HELPFUL HINTS
For best results, grind meat that is very cold or partially frozen. The
grinder parts can be pre-chilled in the refrigerator or freezer before use to
maintain a grinding temperature. For more tender results,some meats can be
ground twice. However, fatty meats should be ground only once.
To grind bread for crumbs,be sure that bread is either oven dried thoroughly
to remove all moisture,or not dried at all. Partially dried bread may jam the
metal food grinder attachment.
NOTE: Very hard, dense foods such as completely dried homemade bread
should not be ground in the metal food grinder attachment. Homemade bread
should be ground fresh and then oven or air-dried.
If using natural casings,it is recommended to first soak them in cold water
for 30 minutes to remove excess salt, then rinse several times by running cold
water through the entire
length of the casing.For best results for sausage,refer also to the
instruction that came with the casings.
CARE AND CLEANING FOR MEAT GRINDER
CLEANING THE METAL FOOD GRINDER ATTACHMENT AND ACCESSORIES
| Use the cleaning brush to clean the main housing and other accessories,
including the grinding plates.
---|---
| The following parts should be hand-washed only, using warm, soapy water and
drying thoroughly: main housing, grind screw, collar, tray, grinding plates,
and blade.
WARRANTY
Dear Customer,
Thank you for choosing the AMZCHEF product. We sincerely hope that you are
satisfied with it.
The manufacturer’s warranty covers the product for a period of 12 months from
the date of purchase against manufacturing faults. All warranties are
automatically kept track of in our system, so there is no need to register
your product.
For an extra 1 year’s free warranty, please register at our official website
www.iamzchef.com or fill in following Warranty
Card, take picture and send to info@iamzchef.com.
Agent/Distributor is welcome to contact us.
Email:info@iamzchef.com.
Any help or questions during use, Quick Contact:
info@iamzchef.com, we will service you within 24
hours. We suggest to provide a warranty card, a photo or a video if there’s
broken spare part or not working machine so that we can be much more clear
about your problems and offer you the best solution.
Warranty Card
Email:……………………………………..
Buyer’s name:……………………………………….
Address:………………………………….
Tel.:…………………………………………..
Order Number:……………………………….
Purchase date:………………………….
Item name:………………………….
Model:……………………………
Serial No ……………………………….
Kindly send back the warranty card to us after filling in the information.
Thanks for your effort!
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>