Lanberg WF01 64-66 V2 Series 19 Inch Wall Mount Cabinets Instruction Manual

19” Wall-mount cabinets
WF01 64/66 V2 series
User’s manual

Important introductory recommendations and usage information of 19”

wall-mount cabinets

1.1 Introduction
PLEASE SAVE THIS MANUAL – it contains a set of recommendations, guidelines, safety rules, restrictions, and operating instructions for Landberg’s 19” wall-mount cabinets, detailing the models supported below:

• WF01-6404-10B| • WF01-6606-00B| • WF01-6609-00B| • WF01-6612-00B| • WF01-6418-10B| • WF01-6427-10B
---|---|---|---|---|---
• WF01-6404-10S| • WF01-6606-00S| • WF01-6609-00S| • WF01-6612-00S| • WF01-6418-10S| • WF01-6427-10S
• WF01-6604-10B| • WF01-6606-10B| • WF01-6609-10B| • WF01-6612-10B| • WF01-6618-10B| • WF01-6627-10B
• WF01-6604-10S| • WF01-6606-10S| • WF01-6609-10S| • WF01-6612-10S| • WF01-6618-10S| • WF01-6627-10S
• WF01-6406-00B| • WF01-6409-00B| • WF01-6412-00B| • WF01-6415-10B| • WF01-6422-10B|
• WF01-6406-00S| • WF01-6409-00S| • WF01-6412-00S| • WF01-6415-10S| • WF01-6422-10S|
• WF01-6406-10B| • WF01-6409-10B| • WF01-6412-10B| • WF01-6615-10B| • WF01-6622-10B|
• WF01-6406-10S| • WF01-6409-10S| • WF01-6412-10S| • WF01-6615-10S| • WF01-6622-10S|

Manual also contains logistic and technical data, instructions, and regulations that must be observed and complied with during transport, assembly, use, and potential maintenance of the products. Under no circumstances should you use the device before carefully reading and fully adapting to all information in the user’s manual. Keep this manual for future reference. All photos and illustrations contained in the instructions are for reference only. The information contained in this manual has been verified and is considered sufficient. The supplier is not responsible for any inaccuracies that may be included in this document, nor is he responsible for updating or keeping the current information in this manual, nor for notifying its users or organization about the updates. In particular, Landberg owners are not responsible for any equipment, software, or data stored/used with the product, including maintenance, replacement, integration, installation, or recovery of hardware, software, or data in the event of misuse of the product or ts components. Landberg brand owners reserve the right to make changes to this manual at any time without notice. The products mentioned in this manual, including the documentation, are the property of the Landberg brand owners and its licensors. Any use or reproduction of these products, including documentation, is prohibited, except as expressly authorized under the appropriate license terms. NOTE: For the most up-to-date version of this manual, please visit our website at www.lanberg.eu.

1.2 Compliance with legal and regulatory provisions regarding safety and the environment
This product complies with EU safety and environmental regulations.
The products listed in the following instructions have been approved for trading within the EU, by obtaining a European Union Declaration of Conformity, which contains a  declaration with the essential requirements and other relevant provisions of the following Directives, and the following harmonized standards have been applied.

Directive: RoHS 2011/65/UE + 2015/863/UE
Standards: IEC 62321-4:2013 + A1:2017; IEC 62321-5:2013;
IEC 62321-6:2015; IEC 62321-7-2:2017; IEC 62321-8:2017;

With the development of products and updates to CE regulations, the declaration may change. The latest declaration of conformity (CE) can be found at: www.lanberg.eu.
NOTE: The use of the WEEE symbol (crossed-out wheelie bin symbol) means that this product cannot be treated as household waste.
Proper disposal of used equipment avoids risks to human health and the environment, resulting from the possible presence of hazardous substances, mixtures, and components in the equipment, as well as improper storage and processing of such equipment. The selective collection also allows you to recover materials and components, from which the device was manufactured. For more information about the recycling of this product, please contact the retail outlet, where the product was purchased, or request information from the local authority.

1.3 Packaging contents
The following items should be provided in the shipping packaging:

• (1x) Front door with 2 grounding pins.
• (2x) Side frame with attached side panel equipped with 2 latches.
• (1x) Top cover with cable entry and 2 holes in the middle for 12×12 cm fans.
• (2x) Flat blank panel for top and bottom cable entry panel.
• (1x) Rear cabinet cover.
• (4x) Vertical mounting rails with ”U” numbered height to install Rackmount devices.
• (1x) Wall-mount rail.
• Essential installation accessories in a string bag: (16x) M48 self-tapping Phillips screws; (8x) M58 self-tapping Phillips screws; (8x) M612 Phillips screws; (1x) plastic asher; (1x) grounding kit (wire, washers, nuts); (1x) front door lock with keys and flat metal latch; (2x) side door lock with keys and curved metal latch; (12x for size < 10 U;  24x for size >= 10 U) M612 Phillips screws with M6 Cage nut; (1x) printed user’s manual.
• (1x) Bottom cover with cable entry and 4 holes with M10 threaded nut on the sides and 2 grounding pins.

1.4 General safety precautions

• The device specifications must be strictly observed when using the product and connecting it to any external products. The specifications of the external devices to which this device is to be connected must also be observed.
• The product cannot be used outside of the rated values in its specification. The warranty does not cover any damage caused by a deviation from these values when using the device.
• All installations, connections, cabling, and circuits in which the product will be used must be made in a manner consistent with locally applicable electricity regulations and in such a way as to eliminate the risk of people walking or tripping over them. Use only power cables with VDE and CE certification when connecting them to the device.  It is necessary to use the same procedures mentioned in this section when connecting the cabling to the product or to the external components.
• For external devices connected to this product, the operating instructions supplied by their manufacturer must be strictly observed.
• To ensure the safety and compliance of the device, use only components or parts that meet the specifications or are recommended by the manufacturer.
• During the warranty period, it is forbidden to replace any elements of the product by its users. Maintenance should be entrusted only to qualify technical personnel, such as the manufacturer’s technical department or an authorized importer.
• If it is necessary to perform maintenance of the device, it should be carried out or supervised by a person having appropriate qualifications and technical knowledge about the device, while maintaining proper precautions. All this is under the local regulations in force.
• If it is necessary to perform maintenance of the equipment or similar activities that will require opening the device or contact with elements that may be under potential voltage, the following safety rules should be observed before carrying out these activities: remove all bracelets, necklaces, rings, watches, or other metal hand and neck objects and use tools with insulated handles.
• Always before performing the equipment maintenance, there should be a person nearby who would react and take appropriate steps to assist the person in charge of the device maintenance in the event of an accident. A person undertaking maintenance should always wash hands after finishing his / her work.
• NEVER allow a situation where sparks or flames could occur near the device. The aftermath of such a situation could have very negative consequences for people and things in the vicinity.
• In the event of a fire, immediately and (without unnecessary delay) disconnect the power supply and notify the fire department of the situation by dialing their assigned emergency number in the country of your stay.
• The product is intended for indoor use. Do not rebuild and/or modify the products and/or their components.
• Under no circumstances, other external products are to be introduced (connected to the device), that are non-compliant with the intended use of that device and/or not intended for that purpose.
• The manufacturer and distributor are not responsible for any damages resulting from improper use and improper handling of the product (not in accordance with this manual).
• Before attempting to attach or disconnect a device, connect or disconnect cables to it in a 19” wall-mount cabinet, please firstly connect all components to a verified and efficient grounding.
• Make sure that all parts assembled from the beginning in a 19” wall-mount cabinet, as well as equipment assembled by the user, are properly screwed or unscrewed when disassembly is carried out. It is unacceptable that any elements of the product or constituting its coherence are not correctly fastened/applied or pose a threat by their incorrect isolation from other functioning factors that in contact would cause danger.

1.5 Guidelines for ESD security principles
To prevent damage to the product, system, or electrical components by electrostatic discharge (ESD), it is vital to be properly prepared and to handle device(s) with care. The following measures are generally sufficient to protect the product against ESD:

• Do not use metal straps or wristbands on your hands to prevent static discharge.
• Touch a grounded metal object first before using/performing the maintenance (if possible) of the device.
• When handling electrical equipment, avoid contact with pins, connectors, and any energy relays.
• When moving electronic components, it is recommended to grab only their (isolated) edges, where there is no current flow. Do not touch components, integrated circuits, memory modules, contacts, etc.
• All electronic devices should be placed back into antistatic bags (if possible) when they are not in use.

1.6 Transport
During transport, store the product only in the original packaging to protect against shocks and bumps. Do not throw the packaging in the trash. When shipping a product under warranty, the product must be in its original shipping box.
1.7 Warranty
The warranty does not apply in the event of product failures and defects resulting from improper use and handling of the device (not under this user manual). Mechanical damage is the basis for rejecting a complaint. To correctly submit a warranty claim, contact your retailer.
1.8 Unpacking and examination
In the presence of the carrier, carefully unpack the product from the shipping box and make sure to check whether:
• Contents of the package include all the elements listed in point 1.3.
• All items are undamaged.
In case of absence, damage, or discrepancies in the elements contained in point 1.3, a damage report has to be drawn up (if any occurred), and the matter has to be submitted to the seller. The following are required: photographs, batch number, and a description of the problem. Indicated actions should be carried out on the same day as the date of product delivery.

1.9 Storage and ventilation

• The product should be installed only in locations with limited access (separate rooms for equipment, etc.).
• Do not install and store the device in places with water (still or running), humidity, or any other liquid substances being present.
• Avoid exposing the product to direct sunlight sources.
• Place the device on a stable, dry surface in a well-ventilated place. Leave at least 100 mm of free space around it to ensure adequate ventilation.
• The device is designed to work only in a controlled environment (controlled temperature and humidity according to the data in the specification, indoors, without conductive pollution present [dust, flammable gases, corrosive substances, etc.]).

Assembly

Be sure to strictly follow the instructions in this manual.
2.1 Preparations
Prepare the appropriate amount of free space on the surface on which the assembly will take place. Carefully remove all elements from the transport box. Further assembly instructions will be based on the diagram provided. Prepare 4 mounting anchors and 4 screws (not included) matching the load capacity of the cabinet’s overall weight. Those elements also have to fit the diameter of the wall-mount rail’s installation holes: 4 – Ø 10.
Due to the use of M6*12 Phillips screws to attach the top and bottom covers with side frames, we recommend a good Phillips screwdriver.
The recommended specification is PH3x150 mm.

2.1.1. Table of components

C
Top cover with cable entry and 2 holes in the middle for 12×12 cm fans| 1x| D
Flat blank panel for top and bottom cable entry panel| 2x| E
Rear cabinet cover| 1x| F
Vertical mounting rails with ”U” numbered height| 4x| G
Wall-mount rail| 1x| H
M48 Self-tapping Phillips screw| 16x| I
M58 Self-tapping Phillips screw| 8x| J
M612 Phillips screw| 8x| K
M612 Phillips screw with M6 Cage Nut| < 10 U: 12x     >= 10U: 24x| L
Plastic washer to be installed under the front door| 1x| N
Grounding kit (wire, washers, nuts)| 1x| M
Front door lock with keys and a flat metal latch| 1x| O
Side door lock with keys and a curved metal latch| 2x| P
Bottom cover with cable entry and 4 holes with M10 threaded nut on the sides and 2 grounding pins| 1x| R
Element| M48 Self-tapping
Phillips screw| M58 Self-tapping
Phillips screw| M6•12 Phillips screw| M6*12 Phillips screw with
M6 Cage Nut
---|---|---|---|---
I| 1| K| L
Illustration| | | |
Supplied quantity| 16A| SA| 8x| < 10 U: 12x       >= 10U: 24x

2.2 19” cabinet installation steps
2.2.1. Front door lock installation

1. Insert the lock module from the string bag marked with [O] symbol through the door so that 2 parallel flat parts of the module are in a horizontal position. The next steps will be for other elements included in this bag.
   Use the keys to set the lock in a vertical position.

2. Screw the washer in by inserting it with engraved triangles side towards the door onto the lock module. Finally, hold the lock module with the door keys and try to tighten the washer tightly.

3. Apply a flat vertical metal lock latch (facing upwards) to the square module element with the screw hole. Next, insert the flat metal round washer and then the star-shaped one. Fix everything together by screwing the bolt into the lock module.
   

2.2.2. Side door lock installation

1. Remove the side door from the side frames [B + C]. Their reassembly will take place during the final assembly of the cabinet.

2. Insert the lock module from the string bag marked with [P] symbol through the door so that 2 parallel flat parts of the module are in a horizontal position. The next steps will be for other elements included in this bag.
    Use the keys to set the lock in a horizontal position.

3. Screw the washer in by inserting it with engraved triangles side towards the door onto the lock module. Finally, hold the lock module with the door keys and try to tighten the washer tightly.

4. Apply the curved metal lock latch horizontally (curved part facing the door) to the square module element with the screw hole. Next, insert the flat metal round washer and then the star-shaped one. Fix everything together by screwing the bolt into the lock module.

5. The same steps 1 ~ 4 should be performed for the 2nd side door [C].

2.2.3. Vertical mounting rails installation

Before further installation, pay attention to where the front and rear sides of the side frames [B + C] are.

1.  Place on a flat surface both side frames [B + C] (without the doors) so that their fronts face your direction.
   The distance between the centers of the small holes in the side frames [B + C] is 25 mm.
   The maximum distance (working depth) between the front and rear vertical mounting rails (taking into account their thickness) is:
   I) For wall-mounted enclosures with a total length of 450 mm: 379.5 mm.
   II) For wall-mounted enclosures with an overall length of 600 mm: 529.5 mm.
   However, it is recommended to install the rear vertical mounting rails on the 3rd hole from the end (50 mm difference) on the side frames to accommodate the devices with the input plug and cable (approx. 55 mm on average).

2. Use 2 vertical mounting rails [G] and adjust the required distance between them on the left side frame [B].
   It is vital to make sure that the numbering of the front vertical rails is in ascending order from right to left (see the provided illustrations). Rear vertical rails also have to e  mounted the same way.

3. Use a total of 4 M5*8 self-tapping Phillips screws [J] to attach the vertical mounting rails to the side frame – 2 screws for each end of the rail.

4. Use 2 numbered vertical mounting rails [G] and choose the same distance as in point 2. on the right-side frame [C].
   It is vital to make sure that the numbering of the front vertical rails is in ascending order from left to right (see the provided illustrations). Rear vertical rails also have to be mounted the same way.

5. Use a total of 4 M5*8 self-tapping Phillips screws [J] to attach the vertical mounting rails to the side frame – 2 screws for each end of the rail.

2.2.4. Installation of side frames with top and bottom cover

1. Prepare the bottom cover [R] so that the cable entry is at the back.

2. Place the left side frame [B] on the left side of the bottom cover and the right side frame [C] on the right side of the cover.
    Before proceeding with the next assembly step, make sure that:I) The height numbering is ascending from bottom to top cover on the front and rear vertical mounting rails.
   II) The pairs of opposite rails are mounted on the same lengths.

3. Place the top cover [D], with cable entry at the back, on the side frames [B + C], and adjust it to their alignment.

4. Use a total of 4 M612 Phillips screws [K ] to attach the top cover to the side frames – 2 on each side.
   Remember to: I) Regularly pay attention to the position of the top cover [D] in regards to the holes in the side frames [B + C]. Do not tighten every screw to the max! First, insert all of them at about 2/3 of their height, check the alignment, and then tighten all screws.
   II) Make sure that the small holes for M48 self-tapping Phillips screws [I] on the front side of both covers and side frames overlap with each other.
   

5. Rotate the whole structure 180 degrees. Adjust the bottom cover [R] to the side frame position.

6. Use a total of 4 M6*12 Phillips screws [K] to attach the bottom cover to the side frames – 2 on each side.
   Remember to:
   I) Regularly pay attention to the position of the bottom cover [R] in regards to the holes in the side frames [B + C]. Do not tighten every screw to the max! First, insert all of them at about 2/3 of their height, check the alignment, and then tighten all screws.
   *II) Make sure that the small holes for M48 self-tapping Phillips screws [I] on the front side of both covers and side frames overlap with each other.**

7. Use a total of 4 M4*8 self-tapping Phillips screws [I] to fix, on the front side, both covers [D + P] with side frames [ B + C] – 1 on each side (see the illustration above).

2.2.5. Rear cabinet cover installation

1. Align the rear cover [F] so that its 6 holes overlap with the 6 holes at the rear of the side frames [B + C].
2. Use a total of 6 M4*8 self-tapping Phillips screws [I] to attach the rear cover to the side frames – 3 per side.

2.2.6. Flat blank panels installation

1. Align flat blanking panel [E] to the cover’s lower cable entry so that the screw holes on both components overlap.
2.  Use a total of 2 M4*8 self-tapping Phillips screws [I] to attach the blanking panel to the lower cable entry – 1 per each side.
3.  Rotate the cabinet structure by 180 degrees.
4. Align another flat blanking panel [E] with the cover’s upper cable entry so that the screw holes on both components overlap.
5.  Use 2 more M4*8 self-tapping Phillips screws [I] to attach the blanking panel to the upper cable entry – 1 per each side.

Cabinet wall installation

1. Prepare (your own) 4 mounting anchors and 4 screws to match the load capacity of the cabinet’s overall weight and the diameter to the holes of the wall-mount rail: 4 – Ø 10.  The distance between the centers of the larger holes on the rail, per side, is 69 mm, and between the centers of the larger holes, at the ends of the rail, (left and right) is 468 mm.
2. Align the wall-mount rail [H] with the surface of the wall and make sure it is leveled.
3. Outline the 4 edges of the wall-mount rail holes (excluding those on the hooks).
4. Drill 4 holes in the outlined spots, then insert the expansion anchors.
5. Re-adjust the rail so that between its 2 L-shaped hooks and the wall there is enough space for attaching the cabinet.
6. Screw 4 bolts into the expansion anchors. First into 2 external holes (1 on each side), others into 2 internal holes.
7. Hang the assembled cabinet by attaching 2 holes at the back on top of the top cover [D] by 2 rail hooks.
8. Use 2 M4*8 self-tapping Phillips screws [I] to fix the rear structure of the cabinet with 2 hooks on the wall-mount rail.

Side door reinstallation

1. Side doors, which should have been removed from the box at an earlier stage of assembly, should be reinstalled in the side frames [B + C]. Simultaneously press 2 latches in the middle of doors, and when they are aligned with the frame holes, release them.
2. Use the keys [P] to lock the side frame door.

Front door installation

1. Put a plastic washer [N] on one of the bottom cover holes [R] on which you plan to place the grounding pin of the front door [A].
2. Insert the lower pin of the front door [A] into the lower hole through the plastic washer, and then insert the upper pin into the hole on the top cover [D] by pressing the hinges (L-shaped) inwards. Release the pressure when it is aligned with the hole.
3.  Use the keys [O] to lock the front door.

Grounding

The cabinet has 4 grounding pins with a diameter of 6 mm:
• 2x on the front door [A].
• 2x on the bottom cover [R].
Grounding wire [M] is included. It consists of 42 conductors made of pure copper (100% CU), 0.16 mm each. The cable cross-section is ~0.9 mm2. A cable is used to connect the bottom cover to the front door (with the possibility of opening it at an angle of up to 180°).
To connect one of the cabinet’s main grounding pins (located on the bottom cover) to the equalizer connection a cable of appropriate length must be purchased separately. Its AWG should be between 17 ~ and 18 and the conductors must be made of pure copper (100% CU) only.

|
---|---

E-mail: support@lanberg.pl | support@lanberg.eu
www.lanberg.pl | www.lanberg.eu

References

• Peryferia do rozbudowy sieci aktywnej i pasywnej | lanberg.pl
• Peryferia do rozbudowy sieci aktywnej i pasywnej | lanberg.pl

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>