easy home 93761-U Flame Effect Heater User Manual

easy home 93761-U Flame Effect Heater

Scope of delivery

Components

Connecting elements supplied

Required tools (not included)

44| ****

Crosshead screwdriver

| 44
---|---|---

45

| ****

Electric drill (for wall mounting)

| 45

General information

Reading and storing the user manual

This user manual accompanies this flame effect heater (hereafter referred to as the “product”), and contains important information on setup and handling.

Before using the product, read the user manual carefully. This particularly applies to the safety instructions. Failure to do so may result in personal injury or damage to the product.
Store the user manual for further use. Make sure to include this user manual when passing the product on to third parties.

Proper use
The product is exclusively designed for the purpose of heating a room. It is only intended for private use and not suitable for commercial purposes. The product is not a children’s toy. Only use the product as described in this user manual. Any other use is considered improper and may result in damage to property or persons. The manufacturer or vendor cannot be held liable for damages or injury incurred through improper or incorrect use.

Explanation of symbols
The following symbols are used in this user manual, on the product or on the packaging.

• This symbol provides you with useful additional information on handling and use.
• WARNING: In order to avoid overheating, do not cover the heater.
• The RCM Mark (Regulatory Compliance Mark) indicates that the product complies with the relevant guidelines of the
• ACMA as well as corresponding government requirements for the safety of electrical devices.

Safety

Signal symbol/word definitions
The following symbols and signal words are used in this user manual.

• This signal symbol/word designates a hazard with moderate risk, which may result in death or severe injury if not avoided.
• This signal word warns of possible damage to property.

General safety instructions

• WARNING – KEEP BATTERIES OUT OF REACH OF CHILDREN
• Swallowing may lead to serious or fatal injury in as little as 2 hours, due to chemical burns and potential perforation of the esophagus.
• If you suspect your child has swallowed or inserted a button battery immediately call the 24-hour Poisons Information Centre on 13 11 26 for fast, expert advice.
• Dispose of used button batteries immediately and safely.

WARNING!

Risk of electric shock!
A faulty electrical installation, excessive line voltage, or incorrect operation may result in an electric shock.

• Only connect the product if the line voltage of the socket corresponds to the data on the rating plate.

• Only connect the product to an easily accessible socket so that you can quickly disconnect it from the power supply in the
  event of a problem.

• Do not use the product if it is damaged or if the mains cord or plug is defective.

• If the mains cord of the product is damaged, the manufacturer, the customer service team or a person with similar qualifications must replace it to avoid risks.

• Do not open the housing; instead, have a qualified professional perform repairs. Contact a qualified workshop for this. Liability and warranty claims are waived in the event of repairs performed by the user, improper connection or incorrect operation.

• Only parts that comply with the original device data may be used for repairs. This product contains electrical and mechanical parts which are essential for providing protection against sources of danger.

• Do not use the product with a programmer, timer, separate remote-control system or any other device that switches the product on automatically, since a fire risk exists if the product is covered or positioned incorrectly.

• Do not immerse the product or the main cord in water or other liquids.

• Never touch the mains plug with wet or damp hands.

• Do not pull the mains plug out of the socket by the cord; instead, always pull it out by the plug itself.

• Never move, pull, or carry the product by its main cord.

• Keep the product and main cord away from open flames and hot surfaces.

•  Lay the main cord so that it does not pose a tripping hazard.

• Do not kink the main cord and do not lay it over sharp edges.

• Only use the product indoors. Do not use the product in damp rooms or in the rain.

• Do not place the product such that there is a risk of it falling into a tub or sink.

• Never reach to retrieve an electrical device if it has fallen into the water. In such a case, immediately disconnect the mains plug.

• Never insert any objects into the housing.

• Always switch the product off and unplug it when you are not using it, when you intend to clean it, or in the event of a
  malfunction.

• The product must not be located immediately below a socket outlet.

• Do not use this product in the immediate surroundings of a bath, a shower or a swimming pool.

• Do not use if there are visible signs of damage to the product.

WARNING

Danger for children and persons with impaired physical, sensory or mental capacities (e.g. partially disabled persons, older persons with reduced physical and mental capacities), or lack of experience and knowledge (e.g. older children).

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Keep children under the age of 8 away from the product and mains cord.
• Do not leave the product unattended while in use.
• Make sure that children do not play with the plastic wrapping.
• They may get caught in it when playing and suffocate.

Risk of fire and injury!
Improper handling of the product may result in a fire or injury.

• WARNING: In order to avoid overheating, do not cover the heater.

• WARNING: Fire risk exists if the heater is covered by or positioned close to curtains or other combustible materials.

• WARNING: Do not use the product if the glass surface is broken.

• The product shall, under no circumstances, be covered with insulating or similar materials.

• Immediately unplug the product if fire or smoke is emitted.

  • Keep textiles, curtains, or any other flammable material a minimum distance of 1.5 m from the air outlet and the sides of
    the product.

• CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given where
  children and vulnerable people are present.

• Avoid touching the surface of the product. Use the handles when moving the product.

• Do not use this product in small rooms when they are occupied by persons not capable of leaving the ro unless constant supervision is provided.

• The product needs to be installed so that the switches and other controls cannot be touched by a person in the bath or
  shower.

• Do not block any openings on the product.

• Always observe the safety precautions if an electric drill is used for wall mounting of the product.

Risk of an explosion, leakage or health hazard!
Improper handling of the batteries may result in explosion, leakage or personal injury.

• WARNING: Do not ingest batteries – Chemical burn hazard! Keep batteries away from children.

• The remote control supplied with this product contains a coin/ button cell battery. If the coin/button battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.

• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

• Store the battery so that it is not accessible for children and animals.

• Immediately dispose of any used or leaky battery in accordance with the applicable guidelines.

• Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the
  product and keep it away from children.

• Do not expose the battery to excessive heat such as from sunshine, fire and the like.

• Only replace the battery by a battery of the same type.

• Ensure that the battery is inserted the right way round, i.e. observe the polarity (+ and –).

• Do not throw the battery in a fire.

• Non-rechargeable batteries are not to be recharged.

• The supply terminals are not to be short-circuited.

• One type CR2025, 3 V battery is required for the operation of the remote control.

• An exhausted battery is to be removed from the product and safely disposed of.

Risk of damage!
Improper handling of the product may result in damage to the product.

• When mounting the product on a wall, make sure that no cables, lines and pipes are damaged.

• When mounting the product on a wall, make sure the screws provided are suitable for anchoring on your wall. Consult a
  professional if in doubt.

• When placing the product on the floor, make sure it is placed on an easily accessible, level, dry, heat-resistant and
  sufficiently stable surface.

• Ensure that the mains cord does not come into contact with hot parts.

• Never expose the product to the effects of the weather (rain etc.).

• Do not use the product if it has been dropped.

• Never fill the product with liquid.

• Never attempt to clean the product by immersing it in water and do not use a steam cleaner to clean it. Otherwise, you
  could damage the product.

• Stop using the product if its parts exhibit cracks or breaks or are deformed. Only replace damaged parts with corresponding original spare parts.

First use

Checking the product and package contents

Risk of damage!
If you are not cautious when opening the packaging with a sharp knife or other pointed object, you may quickly damage the product.
For this reason, be very careful when opening it.

1. Take the product out of the packaging.
2. Check to make sure that all parts are included (see Fig. A).
3. Check whether the product or individual parts are damaged. If this is the case, do not use the product. Contact the manufacturer via the service address indicated on the warranty card.

Basic cleaning

1. Remove the packaging material and all plastic wrappings.
2. Clean all parts of the product before first use as described in the chapter “Cleaning”.

Installation

• The product can be mounted on the wall or placed on the floor.
• A crosshead screwdriver 44 is required for the installation.
• An electric drill 45 is required for wall mounting.

Wall mounting

1. Select a wall with sufficient load-bearing capacity for installing the product.
   Determine the installation location.
   The installation location should be close to a mains socket.
   The minimum distance from the floor to the bottom of the product is 60 cm and the minimum distance from the top of the product to the ceiling is 100 cm. Ensure there is at least 1.5 m of free space around the product. Keep textiles, curtains or any other flammable material away from the product.

2. Line up the upper bracket 11 with the desired installation location and mark the positions of the four screw holes found on the upper bracket on the wall. The upper bracket must be installed horizontally and the mains cord 6 routed to the bottom right of the product.

3. With the help of an electric drill, drill four holes into the wall at the marked locations and then insert four wall plugs 16 into the drilled holes (see step 1 in Fig. B).

4. Install the upper bracket on the wall by aligning the holes found on the upper bracket with the drilled holes. Then drive four screws A 17 through the holes found on the upper bracket and into the wall plugs with the help of a crosshead screwdriver (see step 2 in Fig. B).

5. Attach the lower bracket 12 to the screw holes 7 found at the bottom of the main unit 1 with two screws D 20 (see Fig. C).

6. Attach the main unit to the wall by placing the holder 8 (found on the back of the main unit) onto the upper bracket.

7. Mark on the wall the positions of the two screw holes found on the lower bracket and then temporarily remove the main unit from the upper bracket.

8. Drill two holes in the wall at the marked locations and then insert two wall plugs into the drilled holes.

9. Place the main unit back onto the upper bracket.

10. Attach the lower bracket to the wall by aligning the holes found on the lower bracket with the drilled holes. Then drive two screws A through the holes found on the lower bracket and into the wall plugs.

Placing the product on the floor

The supporting stand and base must be assembled before placing the product on the floor.

1. Place the main unit 1 horizontally.
2. Attach the stand 13 to the bottom of the product with four screws C 19 (see Fig. D).
3. Attach the base 14 to the stand with four screw B 18 (see Fig. E).
4. Place the product on the floor in an upright position. Make sure the floor is easily accessible, level, dry, heat-resistant and sufficiently stable.
   Ensure there is at least 1.5 m of free space around the product. Keep textiles, curtains or any other flammable material away from the produc Use the handles 10 when you need to move the product around.

Inserting and changing the battery

The remote control 15 requires one CR2025, 3 V button cell battery (provided).

1. Turn the remote control over.
2. Pull the battery tray 35 out from the remote control while pushing the tab of the battery tray to the right (see step 1 in Fig. H).
3. Insert a battery into the battery tray. Make sure the polarity is correct (“+” side is facing up) (see step 2 in Fig. H). If you are replacing the battery, take the old battery out of the battery tray before inserting the new one. Dispose of the old battery in accordance with applicable regulations (see chapter “Disposal”).
4. Slide the battery tray back into the remote control so that it locks into place (see step 2 in Fig. H).
   If the remote control is not responsive or not working, the battery power may be low or empty. Replace the battery.

Connecting the product to mains supply

• Fully unwind the mains cord 6 and connect it to a mains socket.

Operation

• Before operation, make sure the product is properly mounted on the wall or placed on the floor, and the mains cord 6 is properly connected to the mains socket (see chapter “Installation”).

• Point the remote control 15 directly toward the front side of the main unit 1 and make sure there are no obstructions between the product and the remote control.

• The product may emit a faint smell when it is first heating up. This is entirely safe and harmless. Make sure there is adequate
  ventilation in the room.

• Make sure the vents 9 are not covered during operation.

• The product emits a beep sound when a button is pressed.

• Once illuminated, the display 4 turns off automatically after about 30 seconds. To activate the display again for operation,
  press any button on the main unit or remote control, then continue to press the desired buttons to control the product.

1. Set the main power switch 3 to the “I” position. The product emits a beep sound and the power on icon 43 lights up in the
   display when the product is connected to the mains supply.

2. Press the on/off button 21 / 26 to turn the product on. The room temperature (°C) shown in the temperature display area is 37 . The flame effect 5 is activated once the product is turned on.

3. Press the heating mode button 25 / 33 repeatedly to cycle through and select the heating mode (indicated by the heating mode icons 36 ).
   Press| Heating mode| Heating mode icon
   ---|---|---
   1×| 1,000 W (Low power)|
   2×| 1,800 W (High power)|

3×| Fan only*| No heating mode icon
4. If low or high power is selected in the previous step, the desired room temperature will flash in the temperature display area. Press the + or – button 22 / 34 to set the desired room temperature (adjustable range: 15–30 °C). 5. Wait a few seconds (without pressing any buttons) until the temperature display area shows the current room temperature again. The desired room temperature is now set.
The product starts to heat up when the room temperature is lower than the set temperature and stops to heat up when the room reaches the set temperature. It will continuously start or stop heating to maintain the set room temperature.

6. Press the flame effect button 23 / 27 to cycle through and select the brightness level (5 levels) of the flame effect. The current brightness level is indicated by the flame brightness icon 41 .
7. To turn the product off, press the on/off button.
8. Set the main power switch to the “O” position to completely cut off the mains supply.
9. Unplug the mains cord when the product is not in use.

Timer

You can set up a timer so that the product will automatically turn on or off at the desired time of the week. Before setting a timer, the current day (of the week) and time must be first set.

Setting the current day and time

You can set the day and time either with the remote control 15 or the control panel 2 of the main unit 1 . With the remote control

1. Press the day button 32 and then press the + or – button 34 to select the current day (of the week).
   The selected day is indicated by the day icon 38 .

2. Press the hour button 28 . The hour time flashes in the time display area 42 .

3. Press the + or – button to set the hour time.

4. Press the minute button 29 . The minute time flashes in the time display area.

5. Press the + or – button to set the minute time.

6. Wait a few seconds (without pressing any buttons) until the minute time stops flashing. The current day and time are now set.

With the control panel of the main unit

1. Press the time button 24 and then press the + or – button 22 to select the current day (of the week).
   The selected day is indicated by the day icon 38 .

2. Press the time button. The hour time flashes in the time display area 42 .

3. Press the + or – button to select the hour time.

4. Press the time button. The minute time flashes in the time display area.

5. Press the + or – button to select the minute time.

6. Wait a few seconds (without pressing any buttons) until the minute time stops flashing.
   The current day and time are now set.

Setting up a timer
Timers can only be set on the remote control 15 .

1. Make sure the current day (of the week) and time are set (see chapter “Setting the current day and time”).

2. Press the week/time button 31 .

3. Press the set up button 30 to select between ON and OFF timer. The selection is indicated by the timer on/off icon 39 .
   Select the ON timer to turn on the product at the desired time of the week. Select the OFF timer to turn off the product at the desired time of the week.

4. Press the day button 32 to select the day (of the week) the timer will activate.
   The selected day is indicated by the day icon 38 .

5. Press the hour button 28 . The hour time flashes in the time display area 42 .

6.  Press the + or – button to set the hour time of the timer.

7. Press the minute button 29 . The minute time flashes in the time display area.

8. Press the + or – button to set the minute time of the timer.

9. Wait a few seconds (without pressing any buttons) until the time display area shows the current day and time again.
   The timer is now set and will activate at the desired time of the week.

Overheat protection

• This product is equipped with an overheat safety feature. When the product’s internal components reach a certain temperature that could cause overheating and possible fire, the product will automatically turn off.
• To operate the product again, unplug the product from the main socket. Then allow the product to cool down to room temperature (around 30 minutes) before using the product again.

Troubleshooting

Some problems may be caused by minor faults that you can fix yourself. To do so, follow the instructions in the following table. If it is still not possible to resolve the problem, contact customer service. Do not repair the product yourself.

properly connected to the mains socket, the mains socket is not defective and power is switched on at the mains socket.

•     Make sure the main power switch 3 is set to the ON ( I ) position.

•     The product is overheated (see chapter “Overheat protection”).

The product is not heating properly.| •     Make sure the product is set to the desired room temperature.

•     Make sure the product is clean and no dust is accumulated at the vents 9 .

Cleaning

WARNING!

Burn hazard!
The product will get hot during operation and may cause burns.
Let the product cool off completely before each cleaning.

NOTICE!

Risk of short circuit!
Water that has penetrated the housing may cause a short circuit.

• Make sure that no water penetrates the housing.
• Never immerse the product in water.

Risk of damage!
Improper handling of the product may result in damage.

• Do not use any aggressive cleaners, brushes with metal or nylon bristles, or sharp or metallic cleaning utensils such as
  knives, hard scrapers and the like. They could damage the surfaces.

• Do not put the product in the dishwasher, as this will destroy it.

  1. Turn off and unplug the product. Then let it cool down completely.
  2. Use a damp cloth to wipe off the main unit 1 and the remote control 15 .
  3.  Let all parts dry completely.
  4. Keep the vents 9 free of dust and dirt with a soft brush or a vacuum cleaner.

Storage

All parts must be completely dry before being stored.

• Always store the product in a dry area.
• Protect the product from direct sunlight.
• Store the product so that it is not accessible to children.

Technical data

• Model: EF-11D
• Rated voltage: 220–240 V~ 50 Hz
• Power: 1,750–2,000 W
• Heat settings: 2 levels (1,000 W and 2,000 W)
• Cord lenght: 1.6 m
• Suitable for room up to: 20 m2
• Battery (remote control): 1× CR2025, 3 V
• Weight: Approx. 12.7 kg
• Dimensions: 66 × 52 × 14.5 cm (without stand)
• Product code: 805409

Disposal

Disposing of the packaging
Carton Foam Bag Sort the packaging before you dispose of it. Dispose of paperboard and cardboard with the recycled paper
service and wrappings with the appropriate collection service.

Disposing of the product

• Should the product no longer be capable of being used at some point in time, dispose of it in accordance with the regulations in force in your city or county?
• Please ensure your recycling information applies to the local regulations.

Batteries and rechargeable batteries may not be disposed of with household waste!
As the end-user, you are required by law to bring all batteries and rechargeable batteries, regardless of whether they contain harmful substances or not, to a collection point run by the city or county, or to a retailer, so that they can be disposed of in an environmentally friendly manner.
labelled with: Cd = cadmium, Hg = mercury, Pb = lead

Warranty Details

The product is guaranteed to be free from defects in workmanship and parts for a period of 12 months from the date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired, replaced or refunded at our discretion. The benefits conferred by this warranty are in addition to all rights and remedies in respect of the product that the consumer has under the Competition and Consumer Act 2010 and similar state and territory laws.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Repair and Refurbished Goods or Parts Notice

Unfortunately, from time to time, faulty products have been manufactured that need to be returned to the Supplier for repair.
Please be aware that if your product is capable of retaining user-generated data (such as files stored on a computer hard drive, telephone numbers stored on a mobile telephone, songs stored on a portable media player, games saved on a games console or files stored on a USB memory stick) during the process of repair, some or all of your stored data may be lost.

We recommend you save this data elsewhere prior to sending the product for repair.
You should also be aware that rather than repairing goods, we may replace them with refurbished goods of the same type or use refurbished parts in the repair process.

Please be assured though, refurbished parts or replacements are only used where they meet ALDI’s stringent quality specifications.

If at any time you feel your repair is being handled unsatisfactorily, you may escalate
your complaint. Please telephone us on 1800 898 750 or write to us at:
Install + Fix Solutions
Unit 1, 9 Kingsbury Street, Brendale, QLD 4500, AUSTRALIA
1800 898 750 (Mon–Fri, 8:30 am–6 pm AEST)
service@wkfe.com.hk

References

• ALDI Supermarkets - Good Different
• Product Registration

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>