OCULAR IOCAP06C-7 IQ Tower Pedestal Charger Installation Guide

OCULAR IOCAP06C-7 IQ Tower Pedestal Charger

IMPORTANT!

• READ THIS ENTIRE DOCUMENT BEFORE INSTALLING
• OR USING THE CHARGER. FAILURE TO DO SO
• OR TO FOLLOW ANY OF THE INSTRUCTIONS AND
• WARNINGS IN THIS DOCUMENT CAN RESULT IN FIRE,
• ELECTRICAL SHOCK, SERIOUS INJURY OR DEATH.
• THE CHARGER MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN.
• THE ENTIRE INSTALLATION MUST COMPLY WITH THE LATEST “AS/NZS3000:2018 & AS/NZS:3008 STANDARDS”

SPECIFICATIONS

PRODUCT OVERVIEW

1. Wi-Fi & 4G Antenna
2. LED Indicator
3. Optional Programmable Button
4. (Charging Port Selection is set up as default
5.  LCD screen
6. RFID card reader
7. Internal MCB-RCD circuit

FEATURES

• Integrated RCD Type B
  The Ocular IQ Tower is designed to meet and comply with the AS/NZS3000:2018 Wiring Rules With an inbuilt integrated RCD Type B, the installer will only need to install a Type A RCBO at the distribution board.

• LCD Screen & RFID Reader
  The Ocular IQ Tower is equipped with a 7 inch LCD screen allowing users to know the status of the charger. Details about the LCD screen can be found on pages 10 – 12. The Ocular IQ Tower charger comes with an inbuilt RFID reader to allow for access control to the charging station. The RFID Reader is compatible with all ISO 14443 A/B RFID Cards.

• Self-Monitoring & Recovery
  The charger will automatically resume charging after a minor fault such as OVP, UVP, OTP or OCP with no user intervention required

• OCPP 1.6J Full Profiles & Smart Charging Support
  The charger supports OCPP 1.6J full profiles, including the latest smart charging to balance the load of charging stations with limited power supply

SAFETY INSTRUCTION.

• Do not install or use the charger near flammable, explosive, harsh, or combustible materials, chemicals, or vapors.
• Turn off input power at the circuit breaker before installing or maintaining.
• Do not use or stop using the charger if it is defective, appears cracked, frayed, broken or otherwise damaged, or fails to operate.
• Do not attempt to open, disassemble, repair, tamper with, or modify the charger.
• The charger is not user serviceable. Contact your installer for any repairs.
• Do not use the charger when either you, the vehicle or the charger is exposed to severe rain, snow, electrical storm or other inclement weather.
• Do not touch the charger sockets with sharp metallic objects, such as wire, tools or needles.
• Do not put fingers into the charger sockets.
• Do not use this charger if the EV charging cable is frayed, has broken insulation, or displays any other indication of damage.
• Do not use this charger if the enclosure or the EV charging connector is broken, cracked, open, or shows any other indication of damage.
• The charger should be installed only by a qualified electrician.
• Make sure that the materials used and the installation procedures follow local building codes and safety standards.
• Incorrect installation and testing of the charger could potentially damage either the vehicle’s
• Battery and/or the charger itself. Any resulting damage is excluded from the warranty for both the vehicle and the charger. Do not operate the charger in temperatures outside its operating range of -30°C to +50°C.
• Ensure that the EV charging cable is positioned properly to the charging sockets.
• Do not use cleaning solvents to clean any of the charger’s components.
• Be careful not to damage the circuit board when removing the power entry knock-out.

INSTALLATION

• Tools Required

  • Slotted #6 screwdriver
  •  Philips #2 screwdriver
  •  Terminal crimper
  •  Adjustable spanner

• Overview of Steps

  • TURN OFF THE POWER SUPPLY.
  • Then follow these steps to install the Charger

• Step 01 – Check Box Contents
  

  • If any components are damaged or missing, please contact your installer or Ocular charging

• Step 02 – Floor Mounting

  • Position the ground mounting bracket to the concrete basement
  • Open the charger backplate with the key provided
  • Remove the screws and open the guard plate.
  • Anchor the charger to the concrete basement

• Step 03 – Power Cable Wiring

  • Cross the power cables through the guard plate
  • Connect the power cables to the connector board

• Step 04 – Internet Connection

  • Option 01 Cellular & Ethernet
  • Option 02 Wi-Fi
  •  Connect your device to the charger Wi-Fi SSID ‘ioc-XXXXXX’, and enter default password ‘IOC12345’.
  •  Open web-based setup page by entering the default IP Address ‘192.168.10.1:8900’, and enter Username ‘admin’ and Password ‘ioc12345’ then click ‘ok’.

• Step 05 – Verify The Installation

  • Verify the power cables are wired properly.
  • Close the RCD to power on the charger unit, and you should see the LED lights sequentially illuminate green.
  • If the LED red light illuminates or flashes, refer to the Troubleshooting table on page 11.
  • Check on the screen display whether internet is available and back office is connected, refer to page 10.
  • Test the live charging process with simulator or electric vehicle if the installation is completely verified

• Step 06 – Secure Cover

  • Reposition the backplate to the charger and lock it with the key.
  • Seal the back cover

LCD DISPLAY SCREEN

TROUBLESHOOTING

MAINTENANCE & REPAIR

• Regularly inspect the Charger. If damage is found, contact your installer or Ocular Charging.
• The Charger contains no user-serviceable components. If unit is not operating correctly, contact your installer or Ocular Charging.
• Wipe the outside of the Pedestal Charger regularly with a clean damp cloth to remove any accumulation of dust and dirt to prevent rust.

References

• EV Charging Stations Australia | Electric Vehicle Charging Stations | Ocular Charging

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>