OCULAR LTE Plus Electric Vehicle Charging Station Installation Guide

: June 12, 2024
: OCULAR

Table of Contents

Ocular LTE Overview
Technical Parameters
Installation Guide
How to program output current
Illustration of Screen and LED
Safety Warning
Maintenance
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OCULAR LTE Plus Electric Vehicle Charging Station

Ocular LTE Overview

Accessories of Tethered Model

Technical Parameters

Level 2 EV Charging Station

Phase Mode: Single Phase
Installation Method: Wall/Stand
Certificate: CE, TUV, RCM
IP Rating: IP66
Rated Voltage: 230VAC +/- 10%
Rated Current: 32A
Maximum Power: 7.2 kW
Ambient External Temp: -25°C ~ +55°C
Enclosure Material: ABS + PC alloy
Warranty: 2 y
Phase Mode: Three Phase
Installation Method: Wall/Stand
Certificate: CE, TUV, RCM
IP Rating : IP66
Rated Voltage : 400VAC +/- 10%
Rated Current : 32A
Maximum Power : 22 kW
Ambient External Temp : -25°C ~ +55°C
Enclosure Material: ABS + PC alloy
Warranty: 2 year

Instruction for Use

Make sure the wallbox is connected to power

◆ Hang the cable on the hook when it is not in use

Installation Guide

Note: Power cables must be crimped with suitable ferrules otherwise product warranty will be voided

How to program output current

Current Selection Mode
Press the silver button on the right hand side of the charger 3 times within 10 seconds This must be done within 60 seconds after starting the charging unit.
Please note that after 60 seconds from starting, the charging unit will continue with its normal booting process. Restart the charger if the button is not pressed in this time.
Charging Current display
The LCD display will automatically switch to a new screen in this mode. It will display the set output current. To change the set output current, press the silver button until you reach the required Amperage. It will start at 32 Amps, and will go down to 6 Amps before returning back to 32 Amps. The current will be changed in 1 Amp intervals.
Finalising new charging limit
In order to finalise the new output current, once you have selected the required Amperage in Step 2, leave the charger for 20 seconds.
Please note: the new output current will be set on the charger. Only licensed electricians are authorised to program hard limits on Ocular charging stations

Illustration of Screen and LED

Real-time power
Three Live Wire data
Charging Time
Power Consumption
Charging Icon
PCB Temperature
Emergency stop
Over Current
Over Temperature
Leakage protection
Short Current

| IDLE| CONNECTED| CHARGING| FINISHED| ERROR
---|---|---|---|---|---
Instruction of LED Status|

OFF

|

Continuous light

|

Rolling

|

Continuous light

|

Red flashing

Note:
The Ocular LTE plus will automatically restart when minor problems occur.
For serious failures, the system cannot automatically recover. In order to remind user of this failure, the system will automatically countdown 10 seconds to restart.

Safety Warning

Regularly check whether the charging station has visible damage.
Make sure that all safety facilities are available at all times and are tested regularly to ensure they can operate normally. Visit ocularcharging.com.au for a yearly maintenance check according to Australian standards.
If a ground fault occurs, it must be assumed that the cable carries voltage. Please confirm that there’s no high-voltage power in the system before inspecting the charging station.
Persons who install and use charging stations must obey the principles and regulations mentioned to ensure personal and equipment safety.
Before powering on the device, please confirm that the device is properly grounded to avoid unnecessary accidents.
All tools’ unnecessarily exposed metal parts should be insulated to prevent them from touching the metal frame to avoid short circuits.
Do not modify, retrofit, or change any part by yourself under any circumstances.
To ensure the service life and stable operation of the charging station, the operating environment should be kept clean as possible with a relatively stable temperature and humidity. The charging station must not be used in a flammable environment or environments with volatile gas.
Be sure to confirm that the input voltage, frequency, circuit breakers and other conditions of the device meet the specifications before the device is powered on

Maintenance

Ocular LTE Plus is only recommended for use in residential applications and use outside of this area (i.e. for commercial application) is outside of warranty.
In order to ensure the normal service life of the charging station and reduce risk, maintenance must be performed every 12 months. The maintenance and installation of the equipment must be completed by a licensed electrician. Visit ocularcharging.com.au to book your service.
The product should be placed at an ambient temperature of -25C~+55C in relative humidity of no more than 95%. The air should not contain acids, alkalis, or other corrosive and explosive gases.
Ocular Charging Stations are subject to stringent quality inspections. From the day of purchase, any problem quality can be reflected to the dealer within two years. Any direct damage or malfunction caused by neglect, incorrect use, installation, usage, repair by the users or natural damage are not covered by the warranty.