BOSCH PKG775FP2E Built In Ceramic Hob Instruction Manual

BOSCH PKG775FP2E Built In Ceramic Hob

Product Information

This product is a built-under hob with an intermediate floor. It contains permanent magnets that may affect electronic implants, such as pacemakers or insulin pumps. Persons with electronic implants must maintain a minimum distance of 10 cm from the appliance. The hob must be installed securely and must be connected to an earth conductor.

Product Usage Instructions

Before installing the hob, create wooden battens in accordance with the drawing provided in the manual. Check and adjust the cut-out dimensions and screw the wooden battens in place so that they are flush with the upper edge of the worktop. For stone work surfaces, bond the wooden battens in place. Then, install the fixing rails in a cut-out that has a depth of 500 mm. Check the household wiring before connecting the appliance. The hob is class I and must only be operated in conjunction with an earth conductor. A separate disconnection device must be provided in the phases in accordance with the installation regulations.
To install the hob, insert it into the wider cut-out on the work surface, ensuring that the power cable is not trapped or routed over sharp edges. When removing the hob, disconnect it from the power supply and push it out from below.

It is important to follow all instructions provided in the manual for safe and efficient usage of this product.

Safe installation

Follow these safety instructions when in-stalling the appliance.

• Electrical connection must only be carried out by a licensed expert. Incorrect connection will invalidate the warranty.
• The safe operation of this appliance can only be guaranteed if it has been installed to a professional standard in accordance with these installation instructions. The in-staller shall be liable for any damage resulting from incorrect installation.

WARNING ‒ Danger: Magnetism! The appliance contains permanent mag-nets. They may affect electronic implants, e.g. pacemakers or insulin pumps.

• Persons with electronic implants must stand at least 10 cm away from the appliance.

Built-under
Do not install refrigerators, dishwashers, non-ventilated ovens or washing machines underneath the appliance.

• If you fit a modular or compact dishwasher of the same brand underneath the appliance, the work- top must be at least 40 mm thick.
• If you fit an oven below the appliance, the worktop must be at least 20 mm thick, in certain cases even thicker. Observe the information in the oven installation instructions.
• Make sure that projecting parts such as the mains housing or the mains cable do not collide, e.g. with a drawer.

Intermediate floor
If the underside of the hob can be touched, an inter-mediate floor must be fitted.

• Ask your specialist retailer for an intermediate floor as an accessory.
• If you use your own intermediate floor, the minimum distance to the mains connection of the appliance must be 10 mm.

Preparing the units
The worktop must be level, horizontal and stable. ¡ The fitted unit must be heat-resistant to at least 90 °C.

• Seal the cut surfaces with heat-resistant material. Fig. 1
  

Inserting the hob into the wider cut-out

1. Create the wooden battens in accordance with the drawing.
2. Check and adjust the cut-out dimensions.
3. Screw the wooden battens in place so that they are flush with the upper edge of the worktop. For stone work surfaces, bond the wooden battens in place.
   Fig. 2 , → Fig. 3

Installing fixing rails
For stone work surfaces, bond the fixing rails in place.

• The hob can also be installed in an existing cut-out that has a depth of 500 mm.
  Fig. 4

Electrical connection
Check the household wiring before connecting the appliance.

• The appliance fulfils the requirements of protection class I and must only be operated in conjunction with an earth conductor.
• In the permanent electrical installation, a partition must be provided in the phases in accordance with the installation regulations.
• If appears on the appliance’s display, it has not been connected correctly. Disconnect the appliance from the mains and check the connection.

Connecting without a pre-installed cable
Only connect the hob in accordance with the connection diagram.

• If required, install the enclosed copper bridges.
• The power cable must correspond to type H05 VV-F or a higher rating.
• Use the current load to determine which wire cross-section you require. A cross-section of < 1.5 mm² is not permitted.

Installing the hob
Do not trap the power cable and do not route it over sharp edges.

• If the oven is a built-under type, route the cable along the rear corners of the oven to the mains socket.
• Push the hob in until it locks into place.
  Fig. 5

Removing the hob

• Disconnect the appliance from the power supply.
• Push out the hob from below.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>