nuna ARRA next Infant Car Seat Instructions
- June 5, 2024
- nuna
Table of Contents
nuna ARRA next Infant Car Seat
Child Usage Requirements
This product is suitable for use with children who meet the following
requirements:
- This is an “i-Size” Enhanced Child Restraint System. It is approved according to UN Regulation No.129, for use in, i-Size compatible vehicle seating positions as indicated by vehicle manufacturers in the vehicle users’ manual.
- If in doubt, consult either the Enhanced Child Restraint System manufacturer or the retailer.
- ARRA next child restraint is compatible with BASE next / ARRA base. Please refer to ARRA base instruction manual for the installation of ARRA base.
WARNING
- Failure to follow these warnings and instructions could result in serious injury or death.
- The rigid items and plastic parts of enhanced child restraint systems shall be so located and installed that they are not liable to become trapped by a moveable seat or in a door of the vehicle.
- DO NOT use the rearward-facing enhanced child restraint systems in seating positions where there is an active frontal airbag installed.
- To use this enhanced child restraint according to UN Regulation No.129, your child must meet the following requirements.
- Child height 40cm-85cm /Child weight≤13kg (approximately 1.5 years old or under).
- Any support leg should be in contact with the vehicle floor and any straps restraining the child should be adjusted to the child’s body. The straps should not be twisted.
- This enhanced child restraint should be replaced when it has been subject to violent stresses in an accident. An accident can cause damage to it that you cannot see.
- Concerning the danger of making any alterations or additions to
- the device without the approval of the competent authority, and a danger of not following closely the installation instructions provided by the enhanced child restraint manufacturer.
- Please keep this enhanced child restraint away from sunlight, because it may be too hot for the child’s skin. Always touch the enhanced child restraint before placing a child in it.
- Children are not left in their enhanced child restraint system unattended.
- Any luggage or other objects liable to cause injuries in the event of a collision shall be properly secured.
- The enhanced child restraint system shall not be used without the soft goods.
- The soft goods should not be replaced with any other than the one recommended by the manufacturer, because the soft goods constitute an integral part of the restraint performance.
- The instructions should be retained on the enhanced child restraint for its life period. For an i-Size Enhanced Child Restraint System, the user shall also be referred to the vehicle manufacturer’s handbook.
Parts List
Make sure all parts are available before assembly. If any part is missing,
please contact Nuna. No tools are required for assembly.
- Handle
- Canopy
- Instruction Manual Storage Compartment (between seat pad and plastic)
- Seat Pad
- Infant Insert
- Webbing Adjustment Button
- Adjustment Webbing
- Shoulder Harness Covers
- Stroller Fix Releasing Button
- Crotch Harness Cover
- Harness Connector
- Buckle
- Handle Adjustment Button
- Backrest Adjustment Button
- ISOFIX Adjustment Button
- Releasing Button
- Load Leg
- Load Leg Adjustment Button
- ISOFIX Guides
- Infant Carrier Rotating Button
- Instruction Manual Storage Compartment
- ISOFIX Connector
Product Use
- Installation Concerns
- This enhanced child restraint is suitable for vehicle seats with i-Size ISOFIX anchor points with the Base. (1)
- DO NOT use the rearward-facing enhanced child restraint systems in seating positions where there is an active frontal airbag installed. (2) Death or serious injury may occur. Please reference vehicle owner’s manual for more information.
- DO NOT install this enhanced child restraint on vehicle seats that face sideways or rearward with respect to the moving direction of the vehicle.
- Please refer to your vehicle owner’s manual for recommended or suggested installation positions. (3)
- It is recommended to install this enhanced child restraint on the rear vehicle seat. (4)
- DO NOT install this enhanced child restraint on vehicle seats movable during installation.
Handle Adjustment
- The handle of the infant carrier can be adjusted to 2 positions. (5) Position for car, hand or stroller transportation. (5)-1 Baby chair position. (5)-2
- To adjust the handle, squeeze handle adjustment buttons on both sides to release it (6)-1, and then rotate the handle until it clicks into any of the 2 positions. (6)-2
Base Installation
- Attach the ISOFIX guides to the vehicle’s ISOFIX anchor bars (see vehicle owner’s manual). (7) The ISOFIX guides can protect the surface of the vehicle seat from being torn. They can also guide the ISOFIX connectors.
- Unfold the load leg from storage compartment. (8)
- Extend the ISOFIX connectors by pressing the ISOFIX adjustment button while pulling on the connector. (9)
- Press the ISOFIX adjustment button to adjust the ISOFIX connectors. Line up the ISOFIX connectors with the ISOFIX guides, and then click both ISOFIX connectors into the ISOFIX anchor bars. (10)
- Make sure that both ISOFIX connectors are securely attached to the vehicle’s ISOFIX anchor bars. There should be two audible clicks and the colors of the indicators on the both ISOFIX connectors should be completely green. (10)-1
- Check to make sure the base is securely installed by pulling on both ISOFIX connectors.
- After placing the base on the vehicle seat, extend the load leg to floor (11). When the load leg is installed correctly, the load leg indicator will show green. Red will be shown when installed incorrectly. (11)-2
- The load leg has multiple positions. When the load leg indicator shows red this means the load leg is in the wrong position.
- Make sure the load leg is in full contact with the vehicle floor pan.
- Squeeze the load leg adjustment button, then shorten the load leg upwards. (11)-1
Attaching Infant Carrier to the Base
- Push the infant carrier down into the base (13), if the infant carrier is secure, the shell indicator will show green. (14)
- Check that the infant carrier is locked onto the base by pulling up on the handle.
- Press the ISOFIX adjustment button, and push the base back until it comes in contact with the vehicle seatback. (15)
- To release the infant carrier, squeeze the infant carrier release button (16)-1, then lift the infant carrier up. (16)-2
Uninstalling the Base
- To remove the base, press the secondary lock button (17)-1 first, followed by the button (17)-2 on the ISOFIX connectors before removing the base from the vehicle seat. (17)
- For transporting, press ISOFIX Adjustment button and move back ISOFIX connectors back into the storage position. (18)
Height Adjustment
for Head Support and Shoulder Harnesses Check that shoulder harness straps are set at the proper height. Please choose the proper height of shoulder harness.
- Shoulder harness straps must be nearest to your child’s shoulders (19), but not above the shoulder line. (20)
- If the Shoulder harness straps are not at proper height, the child might be ejected from the enhanced child restraint if there is a crash.
Backrest Adjustment
There are 3 angles for the backrest. Please press backrest adjustment button
(23) to heighten or lower the backrest. (24)
Securing Child
- Press the rotating button to rotate for easier side loading/unloading of the child. (25)
- Use Infant Insert.
After the child is placed in the enhanced child restraint, check whether the shoulder harness straps are set to the proper height. - While pressing the webbing adjustment button, pull completely the two shoulder harness straps of the enhanced child restraint. (26)
- Unlock the buckle by pressing the red button. (27)
- Place child into the enhanced child restraint and lock the buckle. (28)(29)
- Tighten the shoulder harness straps by pulling the adjustment webbing.
Canopy
- To assemble the canopy, snap the canopy to the rear of seat. (31)
- To open the canopy, pull the canopy toward, and to close the canopy, push it back. (32)
- The canopy window can be opened for ventilation. (33)
Detach & Assemble Soft Goods
see images (34)-(45)
To re-assemble the soft goods, reverse the aforementioned steps.
Cleaning and Maintenance
Clean the frame, plastic parts, and fabric with a damp cloth, but do not use abrasives or bleach. Do not use silicon lubricants as they will attract dirt and grime. To ensure long-lasting use, wipe this product off with a soft, absorbent cloth after using it in rainy weather. Refer to the care labels attached to the soft goods for washing and drying instructions. It is normal for fabric to color from sunlight and to show wear and tear after a long period of use, even when used normally. For reasons of safety, only use original Nuna parts. Check regularly if everything functions properly. If any parts are torn, broken, or missing, stop using this product.
Product Registration
Please fill in the above information. The model number and the manufactured in
date are located on the back and bottom of the Enhanced Child Restraint and
base.
To register your product please visit:
www.nunababy.com
Click the “Register Gear” link on the homepage.
Warranty
We have purposely designed our high-quality products so that they can grow with both your child and your family. Because we stand by our product, our gear is covered by a custom warranty per product, starting from the day it was purchased. Please have the proof of purchase, model number and manufactured in date available when you contact us. For warranty information please visit: www.nunababy.com Click the “Warranty” link on the homepage. Contact For replacement parts, service, or additional warranty questions, please contact our customer service department.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>