nuna IM-000365C MIXXnext Instruction Manual
- June 7, 2024
- nuna
Table of Contents
IM-000365C MIXXnext
Designed around your life
Contents
Product Information
3
Warranty
Contact
IMPORTANT!
Child Usage Requirements
4
KEEP THESE
Warnings
5
INSTRUCTIONS FOR
Parts List
9
FUTURE REFERENCE:
Product Set Up
11
READ CAREFULLY
Product Use
15
Accessories
25
Car Seat Adaptor
MIXX Rain Cover
MIXX Bassinet
Cleaning and Maintenance
29
MIXX next instructions
2
Product Information
Model Number:
Manufactured Date:
The model number and the manufactured in date are located on a label on the
stroller frame.
Warranty
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure.
We have purposely designed our high-quality products so that they can grow
with both your child and your family. Because we stand by our product, our
gear is covered by a custom warranty per product, starting from the day it was
purchased. Please have the proof of purchase, model number and manufactured in
date available when you contact us.
For warranty information please visit: www.nunababy.com
Contact
For replacement parts, service, or additional warranty questions, please
contact our customer service department.
Nuna Baby Australia Pty. Ltd. 82 Bellingara Road Miranda NSW 2228 Ph: 02 8543
5570
Distributed in Australia by Nuna Baby Australia Pty. Ltd. 82 Bellingara Road
Miranda NSW 2228 Ph: 02 8543 5570
Child Usage Requirements
This stroller is suitable for use with children who meet the following
requirements:
Weight: up to 22.7 kg maximum Height: up to 114.3 cm
When using the stroller frame with MIXX bassinet or KLIK plus infant carrier,
refer to the child usage requirements listed in those instruction manuals.
3
MIXX next instructions
MIXX next instructions
4
WARNING
TO AVOID INJURY OR DEATH: ALWAYS APPLY THE BRAKES WHENEVER THE PRAM/STROLLER
IS STATIONARY.
DO NOT LEAVE CHILDREN UNATTENDED. ALWAYS KEEP CHILD IN VIEW WHILE IN PRAM/
STROLLER.
DO NOT USE THE SEAT WITH ANY OTHER MODELS OF PRAM/STROLLER.
SECURE THE CHILD IN THE HARNESS AT ALL TIMES.
USE THIS HARNESS AT ALL TIMES.
ALWAYS USE THE CROTCH COMBINATION WITH THE WAIST BELT. IT IS SUGGESTED THAT
THE SHOULDER HARNESSES BE USED AS WELL.
DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS PRAM/STROLLER.
MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU ADJUST THE PRAM/
STROLLER.
TO AVOID SERIOUS INJURY FROM FALLING OR SLIDING OUT, ALWAYS USE SEAT BELT.
USE THIS TETHER STRAP TO STOP THE PRAM/ STROLLER ROLLING AWAY.
DO NOT USE THIS BASSINET ONCE THE CHILD CAN SIT UP UNAIDED. MAXIMUM WEIGHT OF
THE CHILD: 9KG.
Ensure that all the locking devices are engaged before use.
5
MIXX next instructions
Do not let your child play with this product.
Never leave the harness buckled when not fitted to a child in the stroller
because the harness can form loops which may pose a strangulation hazard.
It is unsafe to use accessories other than those approved by the vehicle
manufacturer.
Adult assembly required.
Use of this stroller with a child weighing more than 22.7 kg or taller than
114.3 cm. in height will cause excessive wear, and stress on the stroller, and
could create an unstable condition. Use the pram/ stroller with only one child
at a time.
To prevent a hazardous, unstable condition, do not place more than 4.5 kg in
the storage basket before use.
To prevent a hazardous, unstable condition, do not place more than 0.45 kg in
the storage pocket on the back of the seat.
Overloading, folding incorrectly, or using component parts from other
manufacturers may cause the pram/stroller to be damaged, broken or unsafe.
Please read the instruction manual carefully.
Please read all the instructions in the manual before using the product.
Please save instruction manual for future use. Failure to follow these
warnings and instructions may result in serious injury or death.
Safety belts and restraint system must be used correctly.
MIXX next instructions
6
Child may slip into leg openings and be strangled if the harness is not used.
Never use pram/stroller on stairs or escalators.
The pram/stroller not be used near an open fire or exposed flame.
Never allow your child to stand on the pram/ stroller or sit in the
pram/stroller with head toward front of pram/stroller.
Never place the pram/stroller on roads or dangerous area.
The pram/stroller is designed for use on flat or gently sloping surfaces and
may be unstable on higher sloping and uneven surfaces, and users should be
made aware of the possibility of the pram/stroller tipping over.
Do make sure all parts are assembled and fastened properly before using the
pram/stroller.
To avoid strangulation, do not place items with a string around your child’s
neck, suspend strings from this product, or attach strings to toys.
To prevent tipping, do not put anything on the handle. Always lift the child
in and out of the pram/ stroller.
Do not lift pram/stroller while child is in pram/ stroller.
Do not use storage basket as a child carrier.
To prevent tipping, never let child climb the pram/ stroller.
7
MIXX next instructions
To avoid finger entrapment or injury to the body, use care when folding and
unfolding the pram/ stroller.
Be sure the pram/stroller is fully open or folded before allowing child near
the pram/stroller.
To ensure your child’s safety, please make sure all parts are assembled and
fastened properly before using the pram/stroller.
Check that the infant child restraint attachment device is correctly engaged
before use.
To avoid strangulation, do make sure your child is clear from the canopy.
Discontinue using your pram/stroller if it is damaged or broken.
Pram/stroller to be used only at walking speed. This product is not intended
for use while jogging.
To avoid suffocation, remove plastic bag and packaging materials before using
this product. The plastic bag and packaging materials should then be kept away
from babies and children.
This product is not suitable for running or skating.
Stroller designed to be used from birth shall recommend the use of the most
reclined position for new born babies.
The parking device must be engaged when placing and removing children.
Please ensure that the storage latch has been properly locked, before lifting
or moving the vehicle.
Do not use or add any mattress other than the one supplied with the bassinet.
MIXX next instructions
8
Parts List
Make sure all parts are available before assembly. If any part is missing, please contact Nuna. No tools are required for assembly.
CHOKING HAZARD: Remove and immediately discard protective end caps from each wheel and wheel hub axle.
1 Front Wheel (x2) 2 Rear Wheel (x2) 3 Car Seat Adaptor 4 Canopy 5 Canopy
Visor 6 Arm Bar 7 Calf Support 8 Handle Adjustment
Button 9 Shoulder Harness Pads 10 Canopy Clips 11 Stroller Frame 12 Buckle and
Crotch Cover 13 Insert
14 Seat Release Button 15 Top Canopy Window 16 Back Canopy Window 17 Stroller
Handle 18 Recline Adjustment
Button 19 Folding Button 20 Seat Ventilation 21 Tether Strap 22 Storage Pocket
23 Storage Basket 24 Brake Lever 25 Rain Cover
9 MIXX next instructions
1 x2 4 5
6
7
1
2 x2
14 25
3
5
6
8 13
9
10 11
12
2
15
16
17
18
19 20 21 22
23 24
MIXX next instructions 10
Product Set Up
Open Stroller 1 – Open the storage latch as shown. 2 – Lift up on the handle
from the sides and rotate to the
rear of the stroller. A “click” sound means the stroller frame is open
completely.
3 – Squeeze the recline adjustment button on the back of
the seat and rotate the backrest to the upright position. Check that the
stroller is open completely before continuing.
Canopy 4 – Zip the canopy visor to the inside of the canopy. 5 – Insert the
canopy clips into the canopy mounts on the
sides of the stroller. A “click” sound means the canopy is assembled
completely.
Front Wheels 6 – Insert the front wheel into the front leg. A “click” sound
means the wheel is assembled completely. Repeat on opposite side. Check the
wheel is securely attached by pulling out.
11 MIXX next instructions
1 2 3
click
4
5
click click
6
click MIXX next instructions 12
1 – To remove the front wheel, press the release button (1)
and detach the front wheel from the front leg (2).
Rear Wheels 2 – Insert the rear wheel into the rear leg. A “click” sound
means the rear wheel is assembled completely. Repeat on opposite side. Check
that the wheel is securely attached by pulling them out.
3 – To remove the rear wheel, press the release button (1)
and detach the rear wheel from the rear leg (2).
Arm Bar
Always secure the child with the harness. The arm bar is not a restraint
device.
4 – Align the arm bar ends with the arm bar mounts, and
insert until it clicks into place (1). A “click” sound means the arm bar is
assembled completely. To remove the arm bar, press the arm bar release buttons
(2) and lift the arm bar up. (3)
5 – For a more compact fold when the seat is rear facing,
press the armbar adjustment buttons (1) and rotate the armbar down (2) until
it clicks into place. NEVER use the armbar in lowered/folded position when
child is in stroller.
6 – Fasten the inner snaps of the seat pad to the inside of
the seating area as shown.
Check Set Up
Stroller frame is latched open
Front wheels and rear wheels securely attached
Canopy mount attached to stroller frame
Arm bar is securely attached
13 MIXX next instructions
1
2 1
2
click
3
4
3 1
1 2
2
click
5
1 2
6
2 1
MIXX next instructions 14
Product Use
1
The parking brake MUST be engaged when the pram/ stroller is stopped and when
placing and removing child.
Securing Your Child
Avoid serious injury from falling or sliding out. Always use the seat belt.
Make sure the harness is adjusted properly and your
child is snugly secured. The space between the child and
the shoulder harness should be about the thickness of
one finger. DO NOT cross the shoulder belts. This will
2
cause pressure on your child’s neck.
1 – Push the center button on the buckle to release the
buckle latch, remove the clips and place your child in the stroller.
2 – Connect the shoulder buckle and hip buckle.
3 – Secure the shoulder buckle and hip buckle to the buckle
latch and repeat on the opposite side.
4 – Fit the harness snugly to your child by pulling the
adjustment straps to tighten (1). Then pull the waist
adjustment straps out (2).
3
Shoulder Harness Position
5 – The upper shoulder harness buckles can be moved up
and down for added adjustment.
15 MIXX next instructions
4
1
1
2
2
5
MIXX next instructions 16
Canopy
1
1 – To open the canopy, pull the canopy toward the front of
the seat. To close the canopy, push it back.
2 – Position the canopy visor forward or backward as
needed. When not in use, fold the canopy visor under the canopy.
3 – Open the zipper on the canopy for extra shade and
ventilation.
4 – For ventilation, flip up the top canopy window cover.
5 – For additional ventilation, flip up the back canopy
window cover (1) and fold down the top canopy window
2
(2).
The canopy is NOT removable.
3
4
5
2 1
17 MIXX next instructions
MIXX next instructions 18
Front Swivel Locks
It is recommended to use the front swivel locks on uneven surfaces.
1 – Squeeze (1) and pull out the front swivel lock (2) to lock
the front wheel forward facing. You may need to move the wheel to get it to
lock.
2 – Push in the front swivel lock to unlock.
Brake 3 – To lock the rear wheels, step down on rear of the brake
lever.
4 – To unlock the rear wheels, step down on front of the
brake lever.
Always apply the brake when the pram/stroller is stopped. Push the
pram/stroller slightly to ensure the brake is engaged.
Handle
The handle has 3 positions.
5 – To adjust the height of the handle, press the handle
adjustment buttons (1) and pull the handle up or down (2).
Recline Adjustment
There are 5 recline positions for the backrest.
6 – To raise or lower the backrest, squeeze the recline
adjustment button, and pull the seat up or down.
1
4
1 1
2
2
5
2
1 1
3
6
19 MIXX next instructions
MIXX next instructions 20
Calf Support
The calf support has 2 use positions.
1 – To raise the calf support, lift up. 2 – To lower the calf support, press
the adjustment buttons
on the sides (1), and push down (2).
Insert 3 – To assemble the insert, place the insert over the seat and
thread the shoulder, waist and crotch harnesses through their respective
slots.
4 – Attach the hook and loop fasteners. Reverse Seat
The seat can be used rear or forward facing.
5 – Squeeze the seat release buttons and lift the seat up. 6 – Turn the seat
in the opposite direction and place on the
seat mounts until it clicks into place. A “click” sound means the seat is
attached.
Check to make sure seat is securely attached by
pulling up on it.
21 MIXX next instructions
1
4
2
1 2
5
1
3
6
click MIXX next instructions 22
Use Tether Strap 1 – Use the tether strap to prevent the stroller
inadvertently
rolling away. Check that when your hand is through the loop, it allows you to
easily control the stroller.
Fold
Before folding, push the canopy to the rear of the stroller.
2 – Squeeze the recline adjustment button on the back
of the seat (1) and rotate the backrest to the stored position (2).
3 – Pull up on the folding buttons (1) and push the stroller
forward to fold (2).
4 – Lock the stroller by tucking the storage latch onto the
storage mount.
5 – Carry the stroller by lifting its handle.
Ensure the storage latch is engaged when lifting or carrying the stroller.
1
4
2
1
5
2
3
12
23 MIXX next instructions
MIXX next instructions 24
Accessories
Car Seat Adaptor
For KLIK plus infant carrier assembly and usage, please refer to the infant
carrier instruction manual.
1 – To attach the adaptors, place the adaptors onto the seat
mounts as shown. A “click” sound means the adaptors are locked.
2 – To attach the infant carrier, place the infant carrier onto
the adaptors, A “click” sound means the infant carrier is locked.
3 – To remove the infant child carrier, lift the infant carrier up
(2) while pressing the stroller release buttons. (1)
4 – The infant carrier angle can be adjusted with our
adjustable adaptors.
5 – To remove the adaptors, lift the adaptors up (2) while
pulling the release buttons. (1)
MIXX Rain Cover
Check that the canopy is completely open before attaching the rain cover.
6 – To assemble the rain cover, place it over the stroller.
ALWAYS check ventilation when the rain cover is on the product. ALWAYS check
that the rain cover has been cleaned and dried before folding. DO NOT fold the
stroller when the rain cover is attached. DO NOT place your child in the
stroller in hot weather with the rain cover attached.
25 MIXX next instructions
1
4
click
2
5
2
1
3
6
1
2
MIXX next instructions 26
MIXX Bassinet
1
For bassinet assembly and usage, please refer to the bassinet instruction manual.
1 – To attach the bassinet, align the sides of the bassinet
with the seat mounts. Place the bassinet directly down until it clicks into
place.
2 – A “click” sound means the bassinet is attached.
When bassinet is installed, make sure the canopy is pulled forward and the handle is locked.
3 – To remove the bassinet, press the bassinet release
buttons (1) and lift up (2).
2
Remove the bassinet before folding the stroller.
27 MIXX next instructions
3 2
1
1
MIXX next instructions 28
Cleaning and Maintenance
Clean the frame, plastic parts, and fabric with a damp cloth, but do not use
abrasives or bleach. Do not use silicon lubricants as they will attract dirt
and grime. Do not store your stroller in a damp place. Clean the stroller
wheels regularly with water and remove any dirt. Clean the adaptor with a damp
cloth and a mild detergent and dry thoroughly. Do not use abrasives. To ensure
long-lasting use, wipe off this product with a soft, absorbent cloth after
using it in rainy weather. Refer to the care label attached to the fabric for
washing and drying instructions. It is normal for fabric to color from
sunlight and to show wear and tear after a long period of use, even when used
normally. For reasons of safety, only use original Nuna parts. Check regularly
if everything functions properly. If any parts are torn, broken, or missing,
stop using this product.
Nuna International B.V. NUNA and all associated logos are trademarks.
29 MIXX next instructions
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>