ETA110090010 Vital Blend DIGI Multipurpose Blender Instruction Manual

ETA110090010 Vital Blend DIGI Multipurpose Blender

INSTRUCTIONS FOR USE
Dear customer, thank you for purchasing our product. Please read the operating instructions carefully before putting the appliance into operation and keep these instructions including the warranty, the receipt and, if possible, the box with the internal packing.

SAFETY WARNINGS

• Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.

• Check whether the data on the type label corresponds with the voltage in your socket. The power supply plug has to be connected to a socket of the electrical installation that conforms to respective standards.

• Never use the appliance if the power cord or power plug are damaged, if it is not functioning correctly or if it has fallen on the floor and been damaged or if it has fallen into water. In such cases take the appliance to a professional service center to verify its safety and correct function.

• This appliance must not be used by children. Keep the device and its supply cord out of reach of children. The device may be used by persons with reduced physical or mental abilities or lack of experience and knowledge only if they are under supervision or they have been instructed about using the appliance safely and understand the potential dangers. Children must not play with the appliance.

• Be careful when pouring hot liquid into the food processing device or the mixer because it may spurt out of the appliance because of the sudden boil.

• If the power cord of this appliance is damaged, the cord must be replaced by the manufacturer, their service technician or by a similarly qualified person, this will prevent the creation of a dangerous situation.

• Always unplug the appliance from the power supply if you leave it unattended.

• Before replacing accessories or accessible parts, which move during operation, before assembly and disassembly, before cleaning or maintenance, turn off the appliance and disconnect it from the mains by pulling the power cord from the power socket!

• Be careful when handling the blender, the knife is very sharp!

• CAUTION: Do not use the appliance with a program, time switch, or any other part that turns the appliance on automatically as there is a risk of fire if the appliance is not covered or placed properly.

• When the appliance is in operation, prevent pets, plants or insects to get in contact with it.

• To press the ingredients to the knife, use the attached pusher only! It has been designed especially for that purpose.

• Every time before the propulsion unit is switched on, the container needs to be attached properly and the lid needs to be placed appropriately so as to close the container. The safety plug or the pusher needs to be inserted in the lid.

• Never remove or attach the container while the propulsion unit is in operation. Thus you avoid the risk of injury or damage to the appliance.

• After finishing work and before cleaning, always switch off the appliance and disconnect it from power supply by taking the power cord connector out of the electric socket.

• The product is intended for home use and similar (in shops, offices and similar workplaces, in hotels, motels and other residential environments, in facilities providing accommodation with breakfast). It is not intended for commercial use!

• The appliance must not be used in damp or wet environment and in any environment with the danger of fire or explosion (spaces where chemicals, fuels, oils, gases, paints and other flammable or volatile materials are stored).

• Maximum time of processing is 6 min. After that, keep the break for approx. 10 min necessary for the motor unit to cool off.

• Correctly placing the bowl on the appliance will release the safety lock and the appliance may be turned on.

• When mixing or stirring liquids, never add more than 2000ml of liquid, and always use the lid. The maximum hot food volume is limited to 1250ml.

• The appliance is equipped with thermal safety fuse which disconnects current supply incase of engine overloading. If it occurs, unplug the appliance and let the appliance getcooled at least 10 minutes.

• Never immerse the drive unit into water and do not wash it in running water!

• Do not switch on the appliance without ingredients put in!

• Do not put more liquid than marked on the dish and always use the lid when mixing or blending liquids.

• Do not process ingredients of higher temperature than approx. 80 °C.

• Use the mixer only in its working position and at places where there is no risk of tipping and insufficient distance from heat sources (e.g. heater, stove, cooker, grill, etc.) and wet surfaces (sinks, basins, etc.)
  Use the appliance only with accessories intended for this type of device. Using another accessory may pose danger to the user.

• Prevent the supply cord to hang loosely over the edge of the working desk where children could reach it.

• The power cord must not be damaged by sharp or hot objects, or open fire, it must not be sunk into water or bent over sharp edges. Never put it on hot surfaces or do not let it hang over the edge of a table or work tables. Hitting, stumbling, or pulling the power cord e.g. by children can result in tilting over or drawing the appliance down and serious injury!

• Use the appliance only with original accessories from the manufacturer.

• Use the appliance only for the purpose it is intended for as specified in this manual. Never use the appliance for any other purpose.

• The manufacturer is not responsible for damage and injuries caused by improper use of the appliance and the accessories (e.g. food deterioration, injury, cutting) and its guarantee for the appliance does not apply in situations when the safety warnings above are not complied with.

Warning
If the blender runs idle (e.g. the blade cannot touch the ingredients), disconnect it from the mains and release the ingredients. The blender cannot run idle for more than 10 seconds!

FEATURES OF THE DEVICE

• A – propulsion unit
  • A1 – propulsion shaft
  • A2 – rubber feeder
  • A3 – locking mandrel for attaching the container
  • A4 – supply cord
• B – control panel
  • B1 – display
  • B2 – “+” button to manually set speed/processing time (increase in value)
  • B3 – “-” button to manually set speed/processing time (decrease in value)
  • B4 – function button to set processing time
  • B5 – function button to set speed
  • B6 – quick set button for the “SMOOTHIE” program
  • B7 – PULSE button to set the maximum rotation speed
  • B8 – quick set button for the “QUICK CLEAN” program
  • B9 – “MENU” button for selection of a pre-set program (MILK, NUTS, ICE, PUREE)
  • B10 – POWER button to start/end the
• C – dish
  • C1 – handle
  • C2 – knife
  • C3 – gasket no. 1
  • C4 – gasket no. 2
  • C5 – nut
• D – lid
  • D1 – plug
  • D2 – lid seal
• E – pusher
• F – sports bottle for beverages (2 pcs)
• G – Thermo insulated cover for sports bottle (2 pcs)

PREPARATION FOR USE

Remove all packaging material, and remove the accessory. Remove all adhesive foils, stickers or paper from the appliance. Before the first use, wash the parts that will be in contact with food in hot water with a detergent, rinse them thoroughly with clean water and wipe till dry, or let them dry. Possible short-time mild smoke when the appliance is operated for the first time is not a defect and the appliance is not subject to a complaint for this reason.

Appliance assembling
Please assemble the appliance according to If you properly put container C on the driver unit, the safety clutch will be released, and you can start using the appliance. Insert the cap D1 or stamper E in the lid opening. Apply the reverse procedure to dismantle.

Control:

1. Switching to standby mode
   – Connect driver unit A to the mains.
   – Put container C on the arrest pins.
   – Once the container is put on, the mixer will automatically switch to standby mode. You will hear a sound signal and the display and button backlight will come on.
   – Then the individual functions may be set.
   Note: Unless you press a button within approx. In 20 seconds, the appliance will switch to energy-saving mode. The display will go out and only the B10 switch button will be flashing.

2. Manual speed setting and time setting
   – Press the B5 button to set the speed. You will hear a sound signal and the B5 button backlight will start flashing. Set the desired speed by B2 and B3 buttons. 9-speed levels are available.
   – Press the B4 button to set the processing time. You will hear a sound signal and the B4 button backlight will start flashing. Set the desired processing time by B2 and B3 buttons. The processing time may be set in the interval from 5 seconds to 6 minutes.
   – Now turn on the mixer by the B10 button.

Use of pre-set programs

• Select the required program using the B9 button. Each time you press a button, you will hear a sound signal and the indicator of the relevant selected program will start flashing.
• The “SMOOTHIE” and “QUICK CLEAN” programs have their own special buttons (B6, B8).
• The selected processing program may be started by pressing the B10 button.
• The individual phases of the pre-set programs are indicated on the B1 display.

Program Total time                                                   Use

name (sec.)

SMOOTHIE| 60| Preparing fruit and vegetable beverages (smoothies)
MILK| 180| Preparing milk cocktails
NUTS| 120| Chopping nuts and making butters
ICE| 80| Chopping ice
PUREE| 90| Preparing fruit purees and vegetable purees
QUICK_CLEAN| 40| Mixer maintenance and cleaning

Notes:  The manually set and pre-set programs may be terminated at any time by pressing the B10 button.

Using PULSE button (B7)
– By pressing and holding B7 button, the maximum rotation speed can be turned on.
– Once released, it stops the speed.

USING THE BLENDER

Put the closed container with the ingredients on the driver unit. Then manually set the processing speed and time, or use a pre-set program (see Control section). The blender is intended for preparation of juices, milk cocktails, smoothies, sauces, ice cream, soups, baby food, diet food, purées, etc. To press larger pieces of ingredients to the knife, use the pusher E.

Recommendation

• For proper ice cube crushing, observe the maximum permitted volume of 1000ml (see the gauge line).
• A minimum quantity of 500g is necessary when processing nuts or making butter. Nuts must be kept within the knife working area by pushing them by stamper during the chopping process.
• Never use the pusher E individually without the lid D.
• You can also process hot liquids up to a temperature of 80 °C, e.g. sauces, soups.
• Never fill the container with liquids that make foam (e.g. milk) up to 2000 so that they do not overflow. In this case we recommend amounts approx. 1250 ml.

RECOMMENDED SPEEDS FOR PROCESSING INGREDIENTS
This is a high-speed blender. The revolutions are within the range of 15000 – 30000 RPM. Always set the speed with regard to the kind and amount of ingredients being processed, and particularly with regard to ripeness of fruit and vegetables.

RECIPES
Consider these following tips for processing examples and inspiration whose purpose is not to provide a manual but to show ways of different food processing.

Raspberry smoothie

Procedure:
Clean and wash the raspberries. Remove the banana peel and break the bananas into smaller pieces. Then place all the ingredients in the blender and mix them till smooth.

Cranberry smoothie

Procedure:
Clean the cranberries and strawberries as required. Then place all the ingredients in the blender and mix them till smooth.

Tomato smoothie

Procedure:
Clean the vegetables thoroughly and cut them into smaller pieces. Then place all the ingredients together with the ice in the blender and mix them thoroughly.

Watermelon smoothie

Procedure:
Wash and dry the strawberries as required. We recommend that you rid the watermelon flesh of the seeds before mixing. In case that you leave seeds in the flesh, you can strain the smoothie through a strainer in the end. Mix all the ingredients thoroughly.

Mango smoothie

Ingredients Amount (1 serving)                Amount (4 servings)

mango| 1 pcs| 4 pcs
peaches| 1 pcs| 4 pcs
lemon| 1/2 pcs| 2 pcs
water| 100 ml| 400 ml

Procedure:
Wash the peaches, remove the seeds. Wash the mango, remove the seed and peel it. Then put everything in the blender. Flavour with squeezed lemon juice, if required. Finally, mix everything thoroughly.

Carrot and apple smoothie

Ingredients Amount (1 serving)                Amount (4 servings)

carrot| 1 pcs| 4 pcs
apples| 1 pcs| 4 pcs
lemon| 1/2 pcs| 2 pcs
water| 100 ml| 400 ml

Procedure:
Wash the carrot and apples, peel and cut them into smaller pieces. Then put everything in the blender. Flavor with squeezed lemon juice, if required. Finally, mix everything thoroughly.

Green tea and almond smoothie

Ingredients Amount (1 serving)                Amount (4 servings)

green tea| 200 ml| 800 ml
almonds| 20 g| 80 g
honey| 2 spoonfuls| 8 spoonfuls

Procedure:
First of all, brew strong green tea and allow it to cool down. Put it then together with almonds and honey in the blender and mix thoroughly.

Banana-strawberry ice-cream

Ingredients Amount (1 serving)                Amount (4 servings)

bananas| 1 pcs| 4 pcs
strawberries| 50 g| 200 g

Procedure:
Peel the bananas, cut them into smaller pieces and freeze them. Use very ripe bananas. Clean and wash the strawberries as required. If you wish, you can freeze them too (it is not necessary). Then put everything in the blender and mix it. When preparing ice-cream, use the pusher to push the ingredients to the knife. Frozen bananas form ice-cream consistency nicely.

Strawberry cocktail

Ingredients Amount (1 serving)                Amount (4 servings)

strawberries| 50 g| 200 g
milk| 200 ml| 800 ml
sugar| 1 spoonfuls| 4 spoonfuls

Procedure:
Clean and wash the strawberries as required. Then put everything in the blender and mix it thoroughly. We recommend using cane sugar for additional sweetening.

Banana cocktail

Procedure:
Peel the bananas and cut them into smaller pieces. Then put everything in the blender and mix it thoroughly. We recommend using cane sugar for additional sweetening.

MAINTENANCE

Do not use coarse and aggressive cleaning agents (e.g. sharp objects, scrapers, diluting agents or other solvents). Clean drive unit with a soft and wet cloth with a little detergent. Clean all accessories in hot water with a detergent right after use (do not use a dishwasher). To clean the knife, pour about 0.5 litre of clear water in the container, select the pre-set program “QUICK_CLEAN”, and turn on the appliance. In case of larger contamination of the knife, repeat the procedure several times, or pour 1 l of water, add
a small amount of detergent and switch the blender on for 1 minute. Some ingredients can colour the accessories in some way. But the change does not affect the function of the appliance and it is not a reason for a claim. This colouring usually disappears after some time. Never dry plastic moldings over a heat source (e. g. heater, electric/gas stove). Store the appliance after cleaning at a dry, dustfree and safe place, out of reach of children and incapacitated people.

Disassembly of the knife C2
The knife C2 can be disassembled using the lever (not included). Place the release lever onto the nut and loosen it by turning it slightly in the direction of the arrow (see Fig. 3). For re-assembly, proceed in reverse order. The jar bottom needs to be placed between the C3 and C4 gaskets. Tighten the nut applying reasonable force. Please make sure that the contact surface and sealing elements are clean, undamaged and properly placed (see Fig. 3).

Replacing the rubber feeder A2
The rubber feeder is inserted in the driver unit shaft and is not fixed there. To remove the feeder, use a suitable tool, such as small screwdriver or narrow pliers, to take and pull the feeder up (see Fig. 1). When placing a new rubber driver, do not push it in by force. On the contrary – find a position that allows easy placement of the driver by turning and positioning it smoothly.
Contact your manufacturer for spare parts and components. More extensive maintenance or maintenance requiring intervention in the inner parts of the appliance must be carried out by professional service! Failure to comply with the instructions of the manufacturer will lead to the expiration of the right to warranty repair!

ENVIRONMENTAL PROTECTION

If the dimensions allow, there are labels of materials used for the production of packing, components and accessories as well as their recycling on all parts. The symbols specified on the product or in the accompanying documentation mean that the used electric or electronic products must not be disposed of together with municipal waste. For proper disposal of the product, hand it over at special collection places where it will be taken over free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Ask for more details at the local authorities or in the nearest collection site. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations. If the appliance is to be put out of operation for good, after disconnecting it from power supply we recommend cutting off the power cord and thus it will not be possible to use the appliance again.

TECHNICAL DATA

• Voltage (V) shown on the type label of the appliance
• Input (W) shown on the type label of the appliance
• Container volume (mI) about 2000
• Weight (kg) about 4.3
• Protection class of the appliance I.
• Size of the product (mm) 190 x 500 x 262
• Input in standby mode is < 1.00 W.
• Noise level: Acoustic noise level of 86 dB(A) re 1pW

The manufacturer reserves the right to change the technical specifications and accessories for the respective models.
WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING, OR IN THE INSTRUCTIONS MANUAL: HOUSEHOLD USE ONLY. DO NOT IMMERSE IN WATER OR OTHER LIQUIDS.TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.

References

• AEG Hausgeräte | Setzen Sie auf Qualität | AEG
• ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>