Temtop M10 Air Quality Tester Rechargeable AQI Monitor User Guide
- June 5, 2024
- Temtop
Table of Contents
Temtop M10 Air Quality Tester Rechargeable AQI Monitor User Guide
Warnings!
- Do not place the detector in the environment with formaldehyde(HCHO) concentration above 0.5mg/m3 and PM2.5 above 50Oug/m3 for a long time. Otherwise, the sensor may be damaged and cannot run normally.
- Do not use the detector in humid environment in order to maintain the detection accuracy.
- Do not cover the air inlet/outlet while in use.
- Try to avoid using the product in the environment with strong ordour or pungent smell. Otherwise the high accuracy electrochemical sensor may be damaged.
Appearance
Specifications
Battery capacity: 2200mAh PM2.5
sensor: Laser PM sensor
Battery life: Approx. 6 hours on a single charge
Measuring range: (PM2.5): 0-9991.tenn3
Input: DC 5V; 0.5A-1A
Resolution (PM2.5): 1pg/m3
Weight: 200g PM2.5
sensor life: 3 years
Dimensions: 82x82x31 mm HCHO
Sensor: Electrochemical sensor
Measuring range (TVOC): 0-5mg/m3
Measuring range(HCHO): 0-2mg/m3
Resolution(TVOC): 0.01mg/m3
Resolution(HCHO): 0.01mg/m3
TVOC sensor life: 3 years HCHO
sensor life: 3 years
Operations
-
Unpack and take out the detector. Place it outdoors for more than 6 hours for calibrations.
-
Turn ON the detector and wait for the countdowns.
-
Use Home Button to display each measured pollutant: HCHO concentration will display after power ON.
Press Home Button to enter PM2.5 concentration display screen. Then press Home Button again to display TVOC concentration.
Press Home Button again to display AQI index. Press Home Button to repeat all these operations.
Note: Double press the Home Button to AUTO repeat these operations per seconds display intervals. Double press the Home Button again to exit AUTO display mode. -
Indicator Lights Introduction
The indicator lights on the panel indicate the corresponding air quality:
| Color | Green | Yellow | Red |
|---|---|---|---|
| Status | Good | Moderate | Unhealthy |
The battery level indicator on the screen indicates the device charging status:
| Color | Yellow | Green |
|---|---|---|
| Status | Charging | Full |
-
When the battery level is low, please charge by connecting it with USB cable and power supply.
-
It is suggested to calibrate the detector after three months usages. Please follow the manual instructions showing below:
- Turn ON the detector and wait for about 10 minutes.
- Use the pin to poke the calibration button until HCHO icon blinks on the screen.
- Place the detector outside for 10 minutes for ventilation.
- When HCHO icon does not blink, it indicates that the calibration has finished.
Parameter Index for reference
| Status Pollutant | Good | Moderate | Unhealthy |
|---|---|---|---|
| PM2.5 | <12µg/m3 | 12.1-55.4kg/m3 | >55.5kg/m3 |
| HCHO | <0.1mg/m3 | 0.1″0.3 mg/m3 | >0.3 mg/m3 |
| TVOC | <0.6mg/m3 | 0.6-1.6mg/m3 | >1.6mg/m3 |
| AQI | <50 | 50-150 | >150 |
- Please contact us or check our website for more detailed index information.
What’s included
- M10 Detector x 1
- USB Cable x 1
- User Manual x 1
Maintenance Log
Date Submitted| Fault Description/Results| Used Spare Parts| Date Delivered|
Repaired by
---|---|---|---|---
| | | |
| | | |
| | | |
| | | |
Elitech (UK) Limited
Unit 13 Greenwich Business Park,
53 Norman Road, London, SE10 9QF
Tel: +44 (0) 208-858-1888
Support: service@elitech.uk.com
Website: www.elitecheu.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>