Telethings Control Box and Home Sensor Thermometer User Manual

Telethings Control Box and Home Sensor Thermometer

BASIC INFORMATION / PRODUCT DESCRIPTION

Thermometer Home Sensor and Control Box are devices intended to control heating system. Communication of devices is performed wirelessly, and the initiator of the communication is Home Sensor. Control Box is directly connected with the heating system, and performs regulation of the heating system based on information gathered from Home Sensor.

Advantages and main characteristics of the devices are:

• Wireless thermostat is extremely small energy consumer
• Wireless thermostat can change location(room) of reading temperature
• Wireless thermostat shows current temperature and set temperature on display
• Wireless thermostat shows indicator of communication with Control Box on display
• Devices can communicate on long distances
• Simple device installation
• Simple device handling
• Multiple Home Sensors can be connected with Control Box

CONTENT OF THE BOX

On picture (Figure 1.) content of the box is shown. Small appearance deviations are possible of some components from the picture.

1. Installation manual
2. Home Sensor
3. Control Box
4. Adapter 7.5 V
5. 868 MHz antenna
6. GSM antenna
7. 2x screw and 2x plastic dowels
8. Duplex tape

HOME SENSOR AND CONTROL BOX MANUAL

Device can be turned ON / OFF by pressing and holding the „Power“ button for 1 second. If the device was turned OFF, on the display it will be shown as on picture (Figure 3. – left), and while holding the button for 1 second display will turn ON. While turning on, display will look like on picture (Figure 3. – right)

Figure 3. Graphical representation of the display before and after turning the device ON

Pressing and holding button „UP“ or „DOWN“, device enters in menu for setting the temperature. Respectively, pressing button „UP“ set temperature increases by 1°C and decreases by 1°C if button „DOWN“ is pressed. On picture (Figure 4.) graphical representation of setting the temperature is shown.

If indicator of communication is not shown (Figure 5.), it is necessary to check the power supply of the Control Box or to initiate registration process (Pairing the devices). If indicator of empty battery is shown, it is necessary to replace batteries on the device.

Figure 5. Interruption of communication between Control Box and Home Sensor

1. Device power supply
2. Electronically controlled switch connector (Relay 1)
3. Electronically controlled switch connector (Relay 2)
4. Electronically controlled switch connector (Relay 3)
5. Electronically controlled switch connector (Relay 4)
6. Antenna connector (GSM)
7. Antenna connector (868 MHz)
8.  Device power indicator
9.  Relay activity indicator

STEPS FOR REGISTRATION (PAIRI NG) OF DEVICES USING BUTTONS

A prerequisite for this process is that ad ding Home Sensors is allowed on Control Box

1. Turn Control Box ON and wait while device is configuring.
2. Turn Home Sensor ON until the main view on display is shown (Figure 4.)
3. Press and hold buttons „UP“ and „DOWN“ on Home Sensor
4. Press and hold buttons „UP“ and „DOWN“ until on display is shown that the registration process is started, then buttons can be released
5. Wait until on display is shown that the registration process is successfully done (Registration?OK)
6. Wait for the radio signal indicator to be shown on the main view of display

RECOMMENDATION FOR USE

Due to the relevance and validity of measurement and regulation, wireless thermostat should not be installed near heat sources, such as radiators, furnaces, refrigerators and other objects which can emit heat in their immediate vicinity. Also, for the same reason, Home Sensor should not be installed near windows or entrance doors. It’s not recommended to install devices (Home Sensor and Control Box) on unstable surfaces, or surfaces which are exposed to vibrations, due to a possible fall of device and physical damage. Keep devices as far as possible from impact of high humidity and liquid sources due to a possible damage of device’s electronic components. Keep the device out of reach of children.

SPECIFICATION

INSTALLATION

Installation of the device Control Box should be done by service engineer or a person licensed for installing Control Box.

Control box installation directions:

1. Turn off power supply on heating system (due to protection against possible electric shock)

2. Twist the antenna (868MHz) on Control Box; on connector designed for antenna (Figure 6.)

3. Twist the antenna (GSM) on Control Box; on connector designed for GSM antenna (Figure 6.)

4. Connect heating system and/or cooling system and Control Box with voltage-free (dry) contact/Connect heating system on electronically controlled switches (Relays), as on picture (Figure 6.)
   (A1 represents connectors for Relay 1., A2 represents connectors for Relay 2. etc.)

5. Connect power supply on Control Box using adapter.

6. Turn power supply on for heating/cooling system.

After wiring Control Box with heating/cooling system (Figure 8.) and connecting to power supply, Control Box is successfully installed. If Control Box was not previously paired with Home sensor, then first thing is to add Home Sensor using mobile application then set the parameters for added Home Sensor. Detail information about using mobile application can be found on page www.telethings.com

Home Sensor preparation directions:

1. Disassemble Home Sensor (Figure 9.)
2. Insert batteries
3. Assemble Home Sensor in original condition

1.  Turn Home Sensor around
2. Skinuti plastic bracket from rear side
3. Remove battery cover

Figure 10. . Steps for inserting batteries and then assembling the device

1. Mounting Home Sensor on the wall using duplex tape
2. Mounting Home Sensor on t he wall using screws

Figure 11. Attaching the rear plastic holder to the wall (or another surface)

Documents / Resources

| Telethings Control Box and Home Sensor Thermometer [pdf] User Manual
Control Box and Home Sensor Thermometer, Home Sensor Thermometer, Control Box Thermometer
---|---

References

• Telethings - Početna

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>