yuyama TG-F321 Tablet Cassette Base User Manual
- June 12, 2024
- yuyama
Table of Contents
User Manual
TABLET CASSETTE BASE
MODEL TG-F321
TG-F321 Tablet Cassette Base
The purpose of this document is to provide an overview of the Tablet Cassette
Base (TG-F321) and how to use it.
This document also explains the correct way to integrate the TG-F321 into the
final product and includes instructions to avoid unexpected problems.
The TG-F321 consists of an antenna board (DK-0081) with antenna layout and
RFID reader/writer IC, etc., and a control board (DK-0086) with
microcontroller, etc. for interfacing the host system and the antenna board.
It complies with FCC Part 15C, RSS-210 Issue 10 and RSS-Gen Issue 5.TG-F321:Width 93, Depth 113, Height 51 (mm)
Wireless Certification Label Character height: approx. 2mm)
TABLET CASSETTE BASE (TG-F321)
Description
The TG-F321 is an integrated transceiver IC for contactless applications.
The TG-F321 manages the frame coding and decoding in Reader mode for standard
applications.
The TG-F321 embeds the Analog Front End for 13.56 MHz Air Interface.
The TG-F321 supports ISO/IEC 14443 B protocols.
Figure 1. TG-F321 application overview
Commands
2.1 Command format
Fields
-
Direction: HOST to TG-F321
-
Direction: TG-F321 to HOST
Note: EchoCode is an exception as it has only one byte (0x55).
2.2 List of commands
Table 1 lists the command set available for standard use.
Table 1. List of commands
Code | Command | Description |
---|---|---|
1 | IDN | Requests short information about TG-F321 and its firmware version. |
2 | Protocol Select | Select communication protocol and specify some protocol- |
related parameters.
4| SendRecv| Sends data using previously selected protocol and receives the
tag response.
7| Idle| Switches the TG-F321 into ThgDetect or Hibernate state and specifies
under which condition to exit nom these states.
8| RdRe g| Reads wakeup flags.
OA| BaudRate| Sets DART baud rate.
55| EchoCode| Performs a serial interface echo.
Other codes| ST Reserved
Power management and operating modes
3.1 Operating modes
The TG-F321 has 2 operating modes: Idle and Active. In Active mode, the
TG-F321 communicates actively with a tag or an external MCU. Idle mode
includes two low consumption states: Hibernate and Tag Detector. The TG-F321
can switch from one mode to another.
Table 2. Operating modes
Mode | State | Description |
---|---|---|
Idle | Hibernate | Lowest power consumption. TG-F321 has to be waken-up |
in order to communicate. Low level on liRQ_IN pin is the only wakeup solute.
Tag Detector| Low power consumption, Tag detection. Wakeup solute is
configurable:
— Timer
— IRQ_lN pin
— SPI SS pin
— Tag detector
INFO (low-fiequency oscillator) is running in this state.
Active| Standby or Reader| Main communication mode. HFO (high-fiequency
oscillator) is running, TG-F321 is able to decode and execute commands from
external MCU. It can switch the reader ON and OFF and communicate with a tag
or an external MCU.
Hibernate and Tag-Detector states can only be activated by a command from the
external MCU. As soon as Application environment any of these states are
activated, the TG-F321 can no longer communicate with the external MCU. It can
only be woken up.
The behavior of the TG-F321 in ‘Tag-Detector’ state is defined by the Idle
command.
Electrical characteristics (Analog Front End Section)
4.1 Absolute maximum ratings
Table 3. Absolute maximum ratings
Symbol | Parameter | Value | Unit |
---|---|---|---|
VCC_5V | Supply voltage (Main) | 6 (Typ.5V) | V |
VCC_12V | Supply voltage (Motor driver) | 18 (Typ.12V) | V |
TA | Ambient operating temperature | -20 to +50 | °C |
Two | Storage temperature | -30 to +60 | °C |
Vim | Electrostatic discharge voltage according to JESD22—A114, Human Body | ||
Model | 2000 | V | |
Prot(1) | Total power dissipation per package | 1 | W |
- Depending on the thermal resistance of package.
Note: Stresses listed above may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at these
or any other conditions above those indicated in the operational sections of
the specification is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Federal Communications Commission (FCC) Statement:
15.105(b)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: -Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver. -Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. -Consult the dealer or an experienced radio/TV
technician for help.
15.21:
You are cautioned that changes or modifications not expressly approved by
the part responsible for compliance could void the user’s authority to operate
the equipment.
FCC RF Radiation Exposure Statement:
- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
FCC RF Exposure requirements:
This device and its antenna(s) must not be co-located or operation in
conjunction with any other antenna or transmitter.
15.19(a):
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference and
- this device must accept any interference received, including interference that may cause undesired operation.
U.S. Responsible Party:| Tian Heng Consulting, LLC
392 Andover Street
Wilmington, MA 01887, United States
---|---
Contact Person:| Healing Dong
Phone: +1-617- 997-4010
Email: info@tianhengconsulting.com
Product Name:| Tablet cassette base
Model Number(s):| TG-F321
Industry Canada Statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>