Telethings L1 – Smart LoRaWAN Thermostat and Relay Box User Manual
- June 5, 2024
- Telethings
Table of Contents
User manual:
Relay Box LoRaWAN
TELETHINGS RELAY BOX LORAWAN USER MANUAL
BASIC INFORMATION / PRODUCT DESCRIPTION
Receiving switch module (Relay Box) is a multipurpose character device. (For
example, in pair with Telethings Thermostat LoRaWAN device, it’s functionality
is regulating heating system). Relay Box is directly connected with the relay-
controlled system, and based on data got from the server (application) it
regulates relay-controlled system by turning relay on or off.
Advantages and main characteristics of Relay Box are:
- The device can be used for different relay-controlled systems
- The device shows an indicator of the relay state
- The device can communicate on long distances
- Simple device installation
- Simple device handling
CONTENT OF THE BOX
In the picture, (Picture 1.) the content of the box is shown. Small deviations in appearance are possible.
- Installation manual
- Receiving switch module (Relay Box)
- 868 MHz antenna
RECEIVING SWITCH MODULE (RELAY BOX) MANUAL
- Power connector
- Electronically controlled switch connector (Relay)
- AC connector – Positive (L)
- AC connector – Negative (N)
- Voltage-free (Dry) contact (Relay input)
- Violate-free (Dry) contact (Relay output)
- Antenna connector
- Device power indicator
- Relay activity indicator
SUGGESTION FOR USE
Before connecting the device to the electrical circuit, be sure to pre-screw the antenna. It is not recommended to place the device on an unstable surface, or a surface exposed to vibrations, due to the possible fall of the device and physical damage. Keep the device as far away as possible from the effects of high humidity and liquid sources due to the possibility of damage to the electrical components of the device or electric shock. Keep the device out of the reach of children. Thank you for following our recommendations.
SPECIFICATION
RECEIVING SWITCH MODULE
Description| Device for regulating heating system based on the information
given from the server
---|---
Server communication| Mandatory sending current relay status to the server
after desired period of time (min. 1 minute, max. 15 minutes)
which user can set on the server. If the device has not communicated with the
server over desired safety period of time, the device will set relay state to
OFF. (min. 20 minutes, max. 240 minutes)
Power supply| 220V ~ 50/60Hz
Device dimensions| 10 x 6 x 2,5cm
Device weight| 100 gr
Temperature| Storage temperature -10°C – +60°C
Operating temperature 0°C – +60°C
Radio signal frequency| 868 MHz
Communication range| Urban environments: up to 2- to 3-km-wide coverage Rural
environments: beyond 5 to 7 km
DEVICE INSTALLATION
Installation of the device must be done by a service technician or a person
licensed to install the device.
Directions for installing receiving switch module:
- Turn the power supply off on relay-controlled (due to protection against possible electric shock),
- Twist antenna (868MHz) on Receiving switch module, on connector intended for antenna (Picture 2.),
- Connect relay-controlled system and receiving switch module with voltage-free contact/Connect relay-controlled system on electronically controlled switch (Relay) like on the picture (Picture 3.),
- Connect receiving switch module’s power supply to the AC power supply. The power supply the diagram is shown in pictures (Picture 2 and Picture 3), if possible, use the power supply for the receiving switch module from a specific system,
- Turn the relay-controlled system’s power supply on.
- Relay-controlled systems can be heating systems, cooling systems, etc.
Receiving switch module (Relay Box)
LORA JOIN PROCEDURE FOR RECEIVING SWITCH MODULE
Once the device is plugged in, the red LED will turn on. After ten seconds, the JOIN procedure with the server will be initiated. If the JOIN procedure is completed successfully, the red and green LEDs will flash three times and the red LED will remain on while the green LED turns off. The red LED is an indicator of a successful JOIN procedure and if it is on, it means that the procedure has been completed successfully. If the red LED continues to flash, it means that the JOIN procedure failed, and it is necessary to reset the device. The green LED is a relay status indicator and if it is on, it means the relay is on. After the device has successfully completed the JOIN procedure, it can start sending and receiving messages from the server (application).
Lejlekuša bb
75320 Gračanica, Bosna i
Hercegovina
Tel: +387 35 700 209
Fax: +387 35 700 201
Mail: info@telethings.com
Web: www.telethings.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>