Hunter 19412 Doherty Four Light Chandelier Instruction Manual
- June 4, 2024
- Hunter
Table of Contents
Hunter 19412 Doherty Four Light Chandelier
Overview
WARNING
- To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
- The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
- All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that
they are read carefully and completely before beginning installation of the
lighting fixture.
PREPARING FOR INSTALLATION
Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. Remove cap nuts (F) from mounting screws (B). Place the mounting plate (A) over the junction box so that mounting screws (B) and nuts (R) extend out away from the ceiling. Depending on the placement of your junction box the position of mounting screws (B) may need to be adjusted to allow the canopy to be flush with the ceiling. Adjust the position of mounting screws (B) so that mounting screws (B) can be exposed 5-6 mm after passing through the canopy (D) to properly fit the cap nuts. Mounting screws (B) can be adjusted by loosening nuts (R) and loosening or tightening mounting screws (B). Once the ideal position of mounting screws (B) has been confirmed, tighten nuts (R) on mounting screws (B) on the front of the mounting plate to ensure that mounting screws (B) are secure. Pull the house wires through the center of the mounting plate (A). Secure mounting plate (A) to the junction box by tightening the screws (C).
ASSEMBLING THE FIXTURE
FOR INSTALLATION AS A PENDANT:
There are 4 12-inch rods (H), and 1 6-inch rod (I) included for each fixture.
Determine the correct number of rods needed for proper hanging height. To
lengthen the fixture, add additional rods. To shorten the fixture, trim the
wires to the desired length. Leave at least 8 to 10 inches of wire in addition
to the desired length and slide any excess rods off the fixture’s wiring to
discard. Keep in mind that you must use at least one rod to hang the fixture.
Thread the wires through the rods and pull the wires until taut before
connecting the rods together. All threads should be engaged but do not
overtighten (some manual straightening of the downloads may be required).
Screw the rod onto the threaded post (J) on the fixture. Screw the top rod to
threads (G) of hanging straight (T). Pull the fixture wires through the top of
the canopy.
FOR INSTALLATION AS FLUSHMOUNT:
Screw rod (L) onto the threaded post (J) on the fixture. Unscrew the hex nut
(Q) from the canopy (D), set aside hex nut (Q) and washers (P, O, N) and
remove the hang straight (T) from the canopy (D). Also, unscrew the threaded
post (M) on the top end of the hanging straight (T) and screw it to the rod
(L). Pass the threaded post (M) of the rod (L) through canopy (D). Place the
washers (P, O, N) over the threaded post (M) and secure them with the hex nut
(Q).
CONNECTING THE WIRES
Have a helper support the fixture’s weight while completing the wiring. Attach the fixture wires to the power supply wires from the junction box. Connect black to black (Live); white to white (grounded); grounding to grounding (green or copper). Twist the ends of the wire pairs together. Then, twist on a wire connector. Make sure all twists are in the same direction. Loop fixture’s ground wire around grounding screw (E) and tighten. If there is no ground wire (green or copper) from the junction box, contact a qualified electrician.
FINISHING THE INSTALLATION
Raise canopy (D) to mounting plate (A) and position mounting screws (B) so
that they protrude through the openings of the canopy (D). Secure canopy (D)
in place with cap nuts (F). Install light bulb (not included) in accordance
with the fixture’s specifications. Do not exceed the recommended wattage. Turn
on the power and test the fixture. Your installation is now complete.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep
cleaning. For regular cleaning, turn off the light and wipe down the fixture
with a clean lint-free cotton or microfiber cloth. Never spray cleaner
directly onto the fixture.
NOTICE
In order to use a 12-in rod by itself, you must first remove the post from
the 6-in rod and install it on one of the ends of the 12-in rod.
Hunter Pro Tip:
Twist or tape wire ends together to make it easier to pass them through the
downloads. Threaded posts may also be removed for easier wire access.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>